SYLLABUS FOR III SEM. B.E. (CIVIL) EXAMINATION
APPLIED MATHAMATICS III 3CE01
UnitI :
Fourier Series : Periodic functions and their Fourier expansions, even and odd functions, change of
interval, half range expansion. 06
UnitII :
Partial Differential Equations : P.D.E. of first order first degree i.e. Lagranee's form Linear
homogeneous P.D. of nth order with constant coefficients, method of separation of variables,
applications to simple problems of vibration of strings and beams, elementry concept of double
pourier series and their applications to simple problems of vibration of ractangular membrane. 08
UnitIII :
Calculus Of Variations :Maxima and minimum of functionals, variations and its properties Eular's
equations, functionals dependent on first and second order erivatives. The RaylighRitz methodssimple
applications. 07
UnitIV:
Matrices :Inverse of a matrix by adjoint method, Rank of matrix, consistency of system of
simultaneous equations and their solutions. Inverse of a matrix by partitioning method, Linear
dependence, Linear and orthogenal transformations, charaoterictic equation, eigen values and eigan
vectors, reduction to diagonal form, statement, verification and use of Caylay  Hamilton Theorem,
statement and use of Sylvestor's Theorem, Quadric form transformation of coordinates,
transformation of forces and couples association of matrices with linear differential equations of 2
nd
order
with constant coefficient 10
UnitV
Numerical Mehods :Errors in numerical calculations. Errors in series approximations. Rounding of
errors solutions of algebraic and transcendental equations. Iteration method, Bisection method, False
position method, Newton Raphaon's method, (and their rate of convergence) Solution of system of
linear equations by Gauss Elimination mehtod. Gauss Jorden method, Gauss Seidel method , Crouts
method and relaxation method, Numerical solution of ordinary differential equation by Taylor series
method. Picards method, Runga Kutta methods, Modified Euler's method. Milnes predictor/corrector
Method 10
UnitVI
Introduction to optimization Techniques Linear programming Simplex method.
1
STRENGTH OF MATERIALS 3 CB2/3ST02
UnitI
Machanical Properties and Uniaxial Problems: Types of force distribution, concept of stress and strain,
stress strain behavior of ductile and brittle material in uniaxial state of stress. Elestic, plastic and
strain hardened zones stressstrain relations, elastic constants, relation between elastic constants.
Uniaxial loading and deformation of simple cases of statically indeterminate problems underaxial
loading, temperature change etc. Thin walled pressure vessel cylindrical and spherical subjected to
internal pressure.
Unit  II
Axial Force, Shear Forces and Bending Moment Diagram : Concepts of free body diagrams, types of
loads, determinate of axial forces, shear forces and bending moment at a sectio. Axial forces and
bending moment at a section. Axial force. SF and BM diagrams in beams and simple frames,
differential relations between shear force and bending moments. Relation between load and shear
force.
UnitIII
Stresses In Beams : Bending stresses in simple beams, assumptions and derivation of simple bending
theory relation between bending moment bending stress and curvature homogeneous and composite
beams. Shear Stresses in simple beams, shear flow and shear stress distribution, shear stress in composite
beams. Combined effect of BM and axial force.
UnitIV
Torsion of Shafts : Torsion of circular sections, assumptions and derivation of relations between torsional
moment, shear stress and angle of twist. Torsional stress in solid and circular sections, torsion in thin
walled hollow sections closely coiled helical springs. Leaf Springs.
UnitV
Deflection of Beams : Derivation of differential equation of moment curvature relation, differential
equation relating deflection and moment, shear and load, Deflecting of simple beams by integration.
UnitVI
State of Stress In Two Dimensions :State of stress in two dimensions, differential equation of equilibrium,
transformation of stresses, principle stresses, maximum shear stresses, Mohrs circle, combined bending
and torsion, combined effect of Torsion and Shear.Shear flow in thin walled sections, concept of shear
center of thin walled sections, unsymmetrical bending.
2
FLUID MECHANICSI 3CE03
UnitI :
Fluids and Their Properties : Definition of fluid, Difference between solids, liquids and gas a fluid
properties mass density, specific weight and specific gravity, viscosity, netwtons quation, coefficients of
dynamic and kinemetic viscosity. Rheological Diagram. Ideal and real fluids. Compressibility and bulk
modulus. Surface tension capillarity, pressure inside a bulb and cylindrical jet vapour pressure and
cavitation. Effect of pressure and temperature on fluid properties. Fluids Pressure and Its
Measurement : Fluid pressure, law of fluid pressure, variation of fluid pressure with depth, pressure and
head, Atmospheric pressure and vacuum. Gauge and absolute pressures. Pressure measurement open and
differential manometers.
UnitII
Hydrostatics :Total hydrostatics pressure on plans and curved surfaced. Centre of pressure. Fluids in
relative equilibrium; fluid masses subjected to horizontal vertical and inclined acceleration. Buoyancy And
Floatation :Buoyant force and centre of buoyancy. Archimedas principle. Metacentre, its determination
by analytical and experimental methods. Statility of floating boides and three states of equilibrium.
UnitIII
Fundamentals of Fluid FlowI : Kinematics of Flow :Velocity, its variation with space and time.
Steady unsteady, uniform nonuniform. One two and three dimensional rotational, irrotational flow.
Acceleration. of fluid particles Normal and tangential acceleration.Stream line, path line, streak line, streak
line, Lagrangian and Eularian approaches in fluid flow description. Equation of continuity in cartesian
coordinates stream functions, velocity potential and potential flow Relationship between stream
function and velocity potential, flow nets, circulation, vorticity, source and sink. Free and forced
vertices.
UnitIV
Fundamental of Fluid Flow  II : Kinetic of Flow : Poreas influencing motion, Eulers equations of
motion, Navierstokes, Reynolds Equations. Bernoullis equation, Assumptions, derivation,
limitations and application, Kinetic energy correction factor. Momentum equation, Impact or Jets,
forces excerten on platespipe bends and closed conduits, momentum : Venturimeter,
orifice meter and flow nozzles. Fluid MeasurementI : Velocity measurement : pitot tube, pitotstatic
tube and prandit tube. Discharge measurement: Venturimeter, orifice meter and flow nozzles.
UnitV
Fluid MeasurementII : Orifices and Mouth pieces; Orifice: defnintion types, Hydraulic coefficients
factor affecting them and their experiments determination. Large orifices and submerged orifices. Time
for exptying tanks by orifices Mounthpieces : Definition and utility, External and Mounthpieces, running
free and running full pressure at Vena contracta, Coefficients of discharge. Flow Measurement And Control
: Notches & Weirs : Definition Types; Rectangular triangular and trapezoidal, End contraction. Co
efficient of discharge and its determination. Error in measurement of head. Velocity of approach and
its effects cipolletti, broadcrested and submerged weirs.
UnitVI
Dimensional Analysis And Theory of Models : Dimensional Analysis; Definition and use fundaments
and derived dimension. Dimensional analysis by Releighs and Buckingham Pi methods. Similitude
Geometric, Kinematic and Dynamic similarities. Predominant forces, Force ratio, Dimension less
numbers and their significances. Behaviour of Real Fluids : Viscous flow : Laminar and Turbulent flows,
Reynolds apparatus critical velocity. Reynolds Number, simple problems on determination of
Laminar and Turbulent flows in pipes.
3
GEOTECHNICAL ENGG. – I 3CEO4
UnitI
Introduction : Formation of soil, residual & transported soil, soil solids generally used in practice such
as sand, gravel, organic silt, clay, Bentonite, Hard pan Cellche, peat; loass, black cotton soil etc. Phases
of Soil : Various soil weight & volum interrelationship. Density index, methods of determining in situ
density.
UnitII
Index Properties & Their Determination : Water content specific gravity sieve analysis particle size
distribution curve, sedimentation analysis Differential and free swell value. Consistency of soil 
Atterberge limits, determination soilstructures and application. Classification of Soil : Criteria of
classification particle size classification Textural classification Unified & I.S. classification system
field identification Expansive solid their indentification and related problems.
UnitIII
Permeability :Darcys law & its validity, Discharge & seepage velocity, factors affecting permeability
Determination of coefficients of permeability by Laboratory and field methods, permeability of
atratified soil. Seepage :Seepage pressure, quick condition, flownets, Laplace equation, method to
draw flownets characteristics & uses of flownets characteristics & uses of flownets, Preliminary problems
of discharge estimation or homogeneous soils, Effective Neural and total stresses in soil mass.
UnitIV
Stress Distribution : Stress distribution in soil Mass Boussinesque, point load, Unifirmly loaded
rectangular & circular areas, Newmarks charts.
UnitV
Consolidation :Compression of laterally confined soil Terzaghis 1D consolidation theory (formation
of Differential equation) determinationof coefficient of consolidation, degree of consolidation.
Determination of preconsolidation pressure, settlement, rate of settlement.Compaction : Mechanics of
compaction factors affecting compaction standard & modified proctot Tests OMC field compaction
equipment quality control.
UnitVI
Shear Strength : Introduction, Mohrs diagram, mohr Coloumbs theory, Measurement of shear
strength by direct shear test, triaxial test unconfied compression testvane shear test sensitivity. Mechanical
Soil Stabilization :Blending of soils, P.I. Concept.
4
ENGINEERING GEOLOGY SCE05
UnitI
Indian Geology : Principles of stratigraphy & the geologic time scale, Physiographic and tantonic
divisions of India, Introduction to the statigraphy of India. Geomorphology : Geomorphology processes,
External and internal agents, Geological action of wind glaciars, running water and oceans and the
resuiting landforms, Geomorphic forms and their consideration in engineering structures.
Unit  II
Structural Geology : Deformation of rocks, poldsparts of fold, nomenclature & classification, effects
on outcrops, identification joints Defination nomenclature and classification. Faults Terminology
nomenclature and classification. Effect on outcrops. Recognition of faults, outliner & inlier. Problems on
dip, strike thickness and depth of rock strata.
UnitIII
Mineralogy : Defination and classification of minerals Ismorphism, polymphism and
pseudomorphism. General chemical and physical characters of the following mineral groups, Silica,
Feldspar, Olivins, Pyroxene, Amphibole Mica, Peilpathoid and clay. Petrology :Rock cycle Igneous Rocks
+ Magma and formation of ignorous rocks Textures and structures. Forms and tabular classification of
igneous rocks. Seimentary rocks : Weathering, Soils, soil profile and soil types, Erosion, Transportation
and deposition of sediments, Sedimentary Environments, Classification of sedimentary rocks.
Matamorphic rocks : Definations & agents of metemorghism Types of metamorphism rocks Zones &
grades of metamorphism, metasomatism anataxis.
Unit  IV
Engineering Geology : (i) Applicationof geology to Civil Engineering projects engineering properties
of rocks. Engineering considerations of structures of rocks. Rock as a construction material building
stone, road metal ballest. Surface and subsurface geotechniucal investigation Geological mapping
sampling, drilling, photogeology geophysical methods. Application of geology to the location, design
and construction of dams and hydraulic structures, bridges, tunnels and buildings.
UnitV
General Geology : Defination and scops of Geology Earth in relation to the Universe gross features and
internal structurs of the earth. Introduction to continental draft and plate tactonies. Isostasy and
deastrophism. Volcanoes and their products Earthquake Engineering : Earthquake waves, Gauses and
effects, magnitude and intensity earthquaks zones of India, asosmic structures.
UnitVI
Geohydrology : Hydrologic cycle : Occurance and distribution of ground water, Water table and water
table maps. Acqucludes, acquifuges and aoguitards confined and unconfined ground water, springs and
gaymeres I,[prtamce amd grpidm water stidoes om Civil Engineering Works. Stability of slopes and
Landelides, causes of lanoslides and their prevention. Environmental aspects of geology.
5
COMPUTER PROGRAMMING 3CE06 / 3ST06
PROGRAMMING IN FORTRAN  95
Unit I
Introduction : Introduction to computer flowchart, Fortran charcter, set coding format, constants and
varibles, hierarchy of arithmatic operations. Arithmatic expressions and statements, relational and
logical operators and expressions, Built  in functions. Input/output : Format Statements
Unit –II
Control Statements : Type Decleration, Subscripted variables, Dimentions, Double Precision, GOTO,
IF, Do statements , PAUSE, STOP and END Statements
UnitIII :
Advanced Topics : Functions & Subroutines , RETURN, COMMON STATEMENTS, BLOCK DATA
SUBPROGRAMS.
PROGRAMMING IN C
UNITIV
Introduction : CFundamentals, CHARACTER SET data type contant & varibles, Declaration of
constants & variables, Expression, Statements, Symbolic Constants. Operator and Expression ,
Arithmatic Operator Unary operator, Relational & Logical operator Assignment operators, the
conditional operator, Libratary function. Data Input & output Interactive progamming preparing & running
a complete simple program.
UnitV
Control statements : Control statemen, THe WHILE statements, dowhile, for nested loop, ifelse,
switch break, continue, goto statement, comma operator.
UnitVI
Advance Topics : Functions, storage class, Arrays, Pointers, structures & Unions, Data files.
6
SYLLABUS FOR IV SEM. B.E. (CIVIL) EXAMINATION
STRUCTURAL ANALYSIS  I 4 CEO1 / 4 ST01
Unit  I
Analysis of fixed and continues beams by theorem of three moments effect of sinking of support.
UnitII
Analysis of continues beams and simple portals (Non sway) using Moment Distribution methods
UnitIII
Rolling loads on simply supported beams with concentrated and uniformly distributed loads, maximum
B.M. and S.F. Influence lines for reactions, bending moments and shear forces in simply supported beams,
cantilevers and beams with overhangs. Influence lines for forces in members of simple trusses and for BM
and SF in panels of simple trusses.
UnitIV
Strain energy method as applied to the analysis of redundant frames and redundant trusses 'up to two
degrees. Determination of deflection of trusses. Willot Mohr diagram. Castiglanos theorems, Maxwells
reciprocal theorem. Battis theorem.
UnitV
Bucking of Columns and beams columns, Eulers and Rankines formula. Analysis of TwoHinged
arches, S.F. and normal thrust, parabolic arches.
UnitVI
Slope deflection method as applied to indeterminate beams & continues beams portal frames, frame
with inclined legs upto 3 degrees of freedom.
BUILDING CONSTRUCTION & MATERIALS 4CE02
UnitI :
Foundations : Necessity and types of foundations. Details shallow foundations. Bearing capacity of soils
and its assessment. Preumptive bearing capacity values from codes. Loads on foundations. Causes of
failures of foundations and remedial measures, Foundation on black cotton soils Setting out foundation
trenches, excavation timbering of foundation trenches. Load bearing and framed structures.
UnitII
Brickwork :Qualities of good bricks, classification of bricks tests on bricks as per as codes. Terms used
in brickwork, commonly used types of bonds in brickwork such as header, stretcher, english and
flamish bonds, principles of construction. Reinforced brickwork, brick knogging Parapets, copings, sills
and corbels, brief introduction to cavity walls, load bearing and partition walls. Masonry construction
using cement concrete blocks and clay walls, load bearing and partition walls. Masonry construction using
cement concrete blocks and clay blocks. Precest construction;introduction to method and
materials.Precast elements likes poles, cover, jallies, steps corbets, truss element etc.
UnitIII:
Stone Work : Stones, cutting and dressing, selection of stones types of stone masonary, principles of
construction joints in masonary. Lifting heavy stones, common building stones in India. Arches and Lintels
: Terminology in contraction, types chajjas and canopies, pre cast Lintels & Arches. Damp Proofing :
Causes and effect of dampness. Various methods of damp proofing
7
Damp proofing in plinth protection, New Techniques of Damp Proofing Damp Proofing in Plinth
Protection, New Techniques of Damp proofing. Epoxy etc.
UnitIV
Floors And Roofs : Floors : General principals, types and method of construction upper floors finisheem
quality and testing floor tiles, synthetic & Creamic Tiles. Roofs : Flat and pitches roofs, roof coverings,
types AND their constructional features. Thermal Insulation.
UnitV :
Stairs : Types of stairs, functional design of stairs. Doors and Windows : Purpose materials of
construction and types.
UnitVI :
Plastering and Pointing : Necessity, types and methods Temporary Timbering : Centering and formwork
shoring, underpining and scaffolding. Painting : White washing, colour washing and distempering new
materials & Techniques.
ENVIRONMENTAL ENGINEERING – I 4CE03
Unit  I
Introduction, Importance and necessity of water supply scheme. Water demand : types of demand,
empirical formulae, factors affecting per Capita demand, variation in demand, design period and
population forecasting methods & examples. (4) Sources of water rain water, Ground watersprings,
infiltration galleries, Dug wells, tube wells, Surface water stream, lake river, impounding reservoirs,
ponds (2) Intake structures : Location typesriver, lake, canal reservoir etc. (2)
Unit II
Conveyance of water: types of pipes joints, fittings, (2) Hydraulic design aspects : friction Mannings,
Hazen William, Harcy Weish bach and problems Minor head losses (4) Rising main and pumps :
Classification working merits and demerits selection of pumps
Unit  III
Water quality: General idea of water borne diseases, Physical, Chemical, & bacteriological
characteristics of water,Standards of drinking water (3) Water treatment: Objective of treatment unit
operations and processes, treatment flow sheet of conventional water treatment plant (3)Aeration :
Purpose, types of aerators Coagulation and Flocculation : Definition, Principals, types of coagulants and
reactions, coagulant doses, types of mixing and flocculation devices. (3)
Unit  IV
Sedimentation : Principles, types of setting basins, inlet and outletarrangements Clariflocculators :
Principles and operation (1) Filtration : Mechanism of filtration, types of filters  RSF, SSF, Pressure
filters, elements of filters UDS, operation and design aspects filter sand specificationES, UC, operational
problems in filtratiion
UnitV
Disinfection :Purpose Mechanism, criteria for good disinfectant various disinfectants their
characteristics, disinfection by chlorination using different forms of chlorine.(4) Distribution systems :
Requirements for a good distribution system, methods of distribution systems and layouts of DS,
appurtenances in water distribution system (3) Leakage and leak detector. Storage reservoirs for treated
water : Types, capacity of reservoir, mass curve
8
UnitVI
Municipal solid waste management: Generation sources, composition, Quality, Methods of
Collection, transportation, treatment and disposal. Recycle, Reuse, Examples on simple hydraulic design
of pipes, estimatiion of population and water quality, plain sedimentation tanks, cascade aerators, filters,
pumps dose of chlorine. Only simple sizing of units no detailed design.
Concrete Technology 4CE04
Unit I
Main constituents of cement Hydration of cement, Water required, Physical properties and testing of
cement. Effect of fineness, Initial final and false setting of cement, Soundness test, Hardening and
compressive strength Grades and different types of cements. Ordinary Portland cement, Rapid
Hardening Cement, G.G. Blast furnace slag cement Low heat Portlant cement, Portland pozzalan cement,
Portland flyash cement. Sulphate resisting cement. Aggregates : Sources of aggregates, classification
and nomenclature, Coarse and fine aggregate, normal weight (light and heavy weight aggregates).
Aggregate characteristics and their significance in strength, workability, placement and compaction
of concrete. Sampling. Particle shape and texture, Bond of aggregate, size & grading of aggregates
strength of aggregate. Mechanical properties and test Specific gravity, bulk density, porosity absorption
of aggregates, moisture content of aggregate, bulking of sand abrasion test, impact value, Deleterious
substances in aggregates, organic impurities clay and other fine material etc.Soundness of aggregate.
Crushed sand. Alkali aggregate reaction. Intorduction of IS: 383 Water  Water quality for mixing and
curing, acceptable water, pH value, Seawater chloride content. Provisions in IS : 456.
Unit  II
Fresh Concrete : Batching, Mechanical mixers, automatic batching and mixing plants. Efficiency of
mixing. Workability Measurement Slump cone test, compacting factor test, flow table. VeeBee
consistometer. Factor affecting workablity, setting time. Significance of w/c ratio. Segregation,
bleeding, voids, permeability. Hot weather concreting. Converyence of concrete. Placing of concrete.
Compactionvibrators. Curing of concreteSignificance, methods of curing, Temperature effect on curing
& strength gain. IS code on curing. Maturity of concrete. Framework for ConcreteIS Code.
UnitIII
Strength of concreteGain of strength, wc ratio. Factor affecting compressive strengthw/c ratio, type
of cement, air entrainment, aggregrate, mixing water, admixtures, curing conditions. Tensile and
flexural strength. Relation between compressive and tensile strength. Failure modes in concrete,
cracking in compression. Impact strength fatigue strength, shear strength, Bond between concrete &
reinforcement. Modulus of elasticity, Poison's ratio. Testing of Hardened Concrete. Compression testcube
strength & cylinder strength,their relation, effect of aspect ratio on strength. Flexural strength of
concrete, Determination of tensile strength, Indirect tension test. Splitting test. Abrasion resistance.
Accelerated curing test. Nondestructive testsignificance. Rebound hammer. Ultrasonic pulse velocity
test.
Unit IV
Mix Design  Process. Statisical relation between mean & characteristic strength, Variance, Standard
deviation. Factor affecting mix properties. Grading of aggregate, aggregate/cement ration etc. Degree of
quality control. Design mix by Road noteno. 4(BS) ACI method.
Unit V
Additives & Admixures. Types of admixtures. Natural productsDiatomaceous earth, calcined clays of
shales, volcanic glasses. By ProductsPozzplonas, fly ash, silica fume, rice husk ash, metakaoline,
G.G> blast furnace slag. admixuresair entraining, water reducing, acceletors, retarders, plasticizers
& Superplasticizers, permeability reducing, grouting agents, surface harderners.
9
Shrinkageearly volume changes, drying shrinkage, mechanism of shrinkage, factor affecting shrinkage.
Influence of curing & Storage conditions, differential shrinkage. Carbonation Shrinkage. Creep
Factors influencing .Relation between creep & time, nature of creep, effect of creep.
UnitVI
Durability of concrete significance water as an agent of deterioration. Permeability of concrete, air
sulphate attack & control. Sea water attack, acid attack, Efforescence. Resistance of crosion, abrasion
and cavitation. Process of rustling of steel.
SURVEYING  I 4CE05
UNIT  I
CLASSIFICATION OF SURVEYS: (4)
a) Chain & Tape Survey, Errors & Corrections, Obstacles in chain surveying, Cross Staff surveying,
b) Construction, use & testing of optical square, line ranger.
COMPASS SURVEYING: (3)
Prismatic & Surveyor's Compass. True & Magnetic Bearing, Local Attraction, Magnetic Declination,
Compass traversing, Adjustments of traverse,
UNIT  II
LEVELLING: (8)
a) Types of Level, Study of Dumpy Level.
b) Profile Levelling: Longitudinal Section And Cross Sections, plotting LSection and Cross section.
c) Reciprocal Levelling: Curvature and Refraction Corrections, distance to the visible horizon.
d) Principle Axes of Dumpy Level: Testing and adjustment of axis of bubble tube and line of
collimation. Sensitivity of Bubble Tube.
UNIT  III
PLANE TABLE SURVEY : (5)
a) Equipment required for plane table surveying and uses. Advantages, Disadvantages and limitations.
b) Methods of Plane table Survey  Radiation, Intersection, Traversing and Resection methods,
Errors of plane table survey.
c) Two Point and Three Point problems and their solution by different methods.
UNIT  IV
THEODOLITE : (10)
a) Introduction to 20" Vernier Theodolite ; Type of Theodolite ; Principle Axes of Theodolite.
b) Use of Theodolite: Measurement of Horizontal angles, vertical angles, Magnetic Bearings,
prolonging a line, lining in, measuring deflection angles, setting out angles, finding out elevation of
objects (Base accessible and inaccessible) by trignometrical
observations.
c) Theodolite traversing: Computation of Consecutive and independent coordinates, adjustment of closed
traverse, Gale's traverse table, omitted measurement, area calculation by coordinates.
d) Testing and permanent of transit Theodolite
10
UNIT  V
TACHEOMETRY  I : (3)
a) Principle of stadia, Fixed hair method with vertical staff to determine horizontal distance and
elevation of the point.
b) Annalatic lens, Contouring (2)
a) Methods, Chrecteristics, interpolation, uses, locating contours.
b) Use of tacheometry in surveying, Tacheometric Contour Survey.
Computation Of Areas & Volumes : (2)
a) Trapezoidal, Simpson's Rule & Other methods of determining the areas & Volumes,
UNIT  VI
CURVES  I : (3)
a) Simple Circular Curves  Element and setting out by linear and angular methods.
MINOR INSTRUMENTS : (2)
Study and use of Abney Level, Box sextant, Indian Pattern clinometer, Subtense bar. Use Of modern
Electronic distance measuring instruments like EDM, geodimeter.
HYDROLOGY AND WATER RESOURCES 4CE06
Unit I
Introduction : Hydrology , Definition , Engineering Hydrology and its importance Development of
Hydrology and allied sciences, Hydrological cycle, hydrological equation and brief description of its
component, The earth and its atmosphere, importance of temperature, humidity and wind in hydrological
studies. Precipitation : Definition and mechanisms pf precipitation, artificial rains, types of
precipitation, orthographic, conventional and cyclonic, Factors affecting precipitation with references to
physiographic divisions of India. Measurement of precipitation : nonautomatic and automatic rain
gauges. Selection of site Density and adequance of rain gauge stations. Optimum number of rain
gauges, radar measurement of rain fall, mass curves, Supplementary rain fall data missing records,
Intensity DurationFrequency and Depth AreaDuration analysis. (9)
UnitII
Infiltration : Definition, mechanism, factors affecting infiltration, infiltration indices, measurment
application on problems. Evaporation and transpiration : Definition, mechanism, Factors affecting
evaporation. Evaporation estimation by pans, water budget energy budget and empirical formulae,
control of evaporation. Transpiration, factors affecting, its measurement and control.
Evapotranspiration and its measurements. Interception and its measurement.
(8)
Unit III
Run Off : Sources and components of rum  off. Classification of streams, factors affecting the run off
process. Estimation methods, measurement of discharge of a stream by AreaSlope and Area Velocity
methods. Hydrographies : Flood hydrgraphs, Definition. Typical Flood Hydrograph and its
componumts, Base flow and base flow separation, unit hydrograph. Theory, SCurves and its uses.
Instanteeous UEG. (9)
11
UnitIV
Statistical Methods: Statisics in hydrological analysis, probability and probability distributions, average
measures of dispresiion, corelation. Analysis of time series, Frequency analysis. Floods : Causes and
effects, Factors affecting peak flows and estimation of peak flows, low flow, Basin flood, Flood routing
and Flood forecasting Economic planning for flood control. (8)
UnitV
Geohydrology : Introduction, Occurrence and distribution of Groundwater, Water table and water
table maps, aquifer, aquiclude, acquired and aquifuge. Groundwater xploration, electrical resistivity
method, confined and Unconfined aquifers, Porosity, Permeablility, specific Yield, Specific retention,
Darcy's law, introduction to hydraulics of wells, Open wells Safe yield test.
Groundwater quality, Geomorphic and geological control on groundwater storage and movement.
Groundwater provices of India. (8)
Unit VI
Groundwater Recharge : Concepts of recharge selection of recharge sites, Recharging methods,
Spreading method, Induced recharge method, Recharge well method Subsurface dams, waste water
recharge, recharge by urban storm run  off, recharge through rain water harvesting.
Project Planning for water resources : Multipurpose projects, Inter basin water transfer and inter state river
disputes. Water resources planning through planning through watershed management. Economic planning
for domestic and industrial water supply. (6)
V Semester B.E. (Civil )
5CE01 \ 5ST01 STEEL STRUCTURES (3L+1T+2D)
SECTIONA
UNIT I
1. Steel as a structural material, various grades of structural steel , properties, various rolled steel sections (
including cold formed sections, structural pipe (tube) sections) and their properties. Introduction to I.S.
800,808,816,875 etc. ( 8)
2. Design of axially loaded members: (a) Tension members, (b) Compression members (9)
3.Design of roof truss: Load assessment for DL, LL and WL. (6)
UNIT II
4. Design of simple and builtup beams: Laterally restrained and unrestrained, (symmetrical as well as
unsymmetrical section). Curtailment of flange plates. (10)
SECTIONB
UNIT III
5. Design of welded plate girder, concept of gantry girder. (8)
6. Design of single rolled steel section column subjected to axial load and biaxial moment including base
design. (8)
7. Design of axially loaded built up columns. Laced and battened (Column bases slab base gusseted base
moment resistant bases) (9)
12
UNIT IV
8. Structural Fasteners:
A) Behaviour of bolted and welded connections (types, Designations, properties, permissible
stresses), failure of bolted and welded joints. Strength of bolt and strength of weld. Efficiency of joints.
Design of simple bolted and welded connections. Moment resistant bolted and welded connection.(bending
and torsion) (6)
B) Design of connection: Beam to beam, beam to column: framed connection.
(9)
Term Work
Minimum two design assignments based on above topics along with the detailed structural drawings on A2
size sheets. Examination shall be based on the above Practical work.
V01
5CE02 :ENVIRONMENTAL ENGINEERING – II (3L+1T)
SECTIONA
Unit – I
1. General Aspects of Enviromental Engineering  System of collection and conveyance of sewage 
seperate and combined systems, patterns of sewage collection systems. Quantity of storm water and
sanitary waste water sewer:Types,Shapes,Hydraulic Design(Capacity, Size, Grade, etc.) (8)
Unit  II
2. Construction of sewer  Shoring, Trenching and laying to grade. Sewer materials Sewer Appurtences
 manhole street inlets, storm water overflows, inverted syphons, flushing and ventilation. House
plumbing systems  sanitary fitting and appliances, traps, antisyphonage, inspection chambers and
intercepting traps. Sewage pumping  location of pumping station and types of pumps. Sewer testing
and maintenance. (8)
Unit  III
3. Physical and chemical characteristics of wastewater, significance of BOD,COD,BOD rate constant,
Sewage treatment flow sheet, site selection for sewage treatment plant Preliminary and primary
treatment  Screens, Grit chambers, Primary settling tank(including simple design) (8)
SECTIONB
Unit  IV
4. Secondary treatment  Principle of Biological Treatment Activated sludge process, trickling filter,
Methods of disposal  disposal on land and in water stream, Sewage farming, self purification of
stream. Sludge digestion, sludge drying beds .(8)
Unit  V
5. Rural sanitation Pit privy, aqua privy, biogas recovery. Septic tank including soak pit, (including
design problem)Sullage collection and disposal. (5)
6. Industrial Waste Water Treatment – Significance of Industrial Waste Water Treatment, important
physical and chemical parameters, unit operations and treatment processes( flow equalization,
neutralization, adsorption, chemical and biological treatment etc.)
(5)
Unit VI
7. Introduction to air pollution Sources of air pollution and its classification Ill  effects of air pollutants
on man, animal & materials Meterological parameters Methods of air pollution control. ( 8)
13
Reference Books :
1. B.C.Punmia, " Waste Water Engineering "  Laxmi Publication
2. S.K.Garg, "Environmental Engineering"  Vol II Standard Publication.
3. G.S.Birdie, "Water Supply & Sanitary Engineering"
4. M.J.Macghee, "Water Supply & Sewage  McGraw Hill Publication
5. M.N.Rao & H.V.N.Rao, "Air Pollution" McGraw Hill publicatin
6. C.S.Rao,"Enviromental Pollution Control Engineering,
5CE03: SURVEYING – II (3L+1T+2P)
SECTIONA
UNIT I
Tacheometric Surveying (8)
Classification , principal of stadia method, theory of Anallatic lens, distance and elevation formulae,
tangential method, errors in stadia surveying.
UNIT II
Simple ,Compound, Reverse Curves, Vertical Curves. (8)
a) Simple Curves: Elements of simple curves, methods of curve ranging, obstacles in setting out curves.
(4)
b) Compound Curves: Elements of compound Curves, setting out the curve. (1)
c) Reverse Curves: Elements of reverse Curves, setting out the curve. (1)
d) Vertical Curves: Elements of vertical curves, types, tangent correction, location of highest or lowest
point. (2)
UNIT III
Transition Curves (8)
Elements of transition curves, superelevation, length of transition curve, Ideal transition curve, characteristics
of transition curve , setting out the transition curve.
SECTIONB
UNIT IV
Geodetic Surveying and Triangulation Adjustment (10)
a) Geodatic Surveying: Classification of triangulation survey, intervisibility of stations, field work,
reduction to centre, base line measurement ,corrections. (7)
b) Triangulation Adjustment: Definitions,weighted observations, laws of weights, station adjustment,
figure adjustment( triangle only) (3)
UNIT V
Photographic Surveying (8)
Basic definitions, terrestrial and aerial photography,tilt and height displacements,heights from parallax
measurements, flight planning, study of phototheodolite and stereoscope.
14
UNIT VI
Astronomy, Remote Sensing ,GIS & GPS (8)
Astronomy: Elements of spherical trignometry , Napier’s rule of circular parts,celestial sphere,
astronomical terms. (2)
Remote Sensing: Introduction, definitions, Remote sensing systems, advantages over conventional
system,energy interaction in the atmosphere, Indian remote sensing satellite series and their characteristics
(3)
GIS & GPS: Components of geographical information system (GIS),advantages, function of GIS, Raster
and vector data, advantages and disadvantages, global positioning system.(GPS),Introduction,
definitions,GPS receivers, antenna, advantages of GPS. (3)
List of Practicals:
A) PRACTICALS: Any five Practicals out of following:
1. Determination of constants of Tacheometer.
2. Determination of elevation of points by Tacheometric surveying.
3. Determination of elevation of points and horizontal distance between them by Tacheometric survey.
4. Determination of gradient of given length of road by Tacheometric survey.
5. Setting out of simple circular curve by offsets from chord produced method
6. Setting out of simple circular curve by Rankine method of tangential angle.
7. Setting out of simple transition curve by tangential angle method.
8. Study of streoscope.
B) SURVEY CAMP: On any of the following topics for minimum three days.
1. Road Project
2. Irrigation Project
3. Water Supply Project
Reference Books:
1) Surveying & Levelling by B.C.Punmia (Vol 2 & Vol 3)
2) Surveying & Levelling by Kanetkar & Kulkarni (Vol 2)
3) Remote sensing & G.I.S. by Dr.M.Anji Reddy
15
5CE04 Transportation Engineering – I (3L+1T+2P)
(Highways & Bridges)
SECTIONA
Highways:
Unit  I:
1. Development & Planning: Road transport Characteristics, Classification of roads, development plants,
network patterns, data collection & surveys, principles of alignment, evaluation of plan proposals.(5)
2. Traffic Engineering: 3E`s of, traffic characteristics, Surveys, Intersectiontypes, layouts, design
principles, Urban traffic, parking, lighting, Accidents,Traffic control Devicesmarking, Signs,
Signals, Regulations Motor Vehicle Act & Rule. (5)
Unit  II:
3. Geometric Design: Road, road user & road vehicle characteristics, Factors affecting design
standards. Cross Section elements, stopping & overtaking sight distance overtaking zones.
Horizontal alignmentCurves, design of super elevation , widening, `transition curves, vertical
alignments, Design of summit & Valley Curves,I.R.C. standards for Geometric Design, Geometrics
of Hill Roads (7)
4. Pavement Design:
Types of pavements & characteristic,Design parameters,Axel & Wheel load,tyre pressure,ESWL for
dual Wheels, repetitions,Group Index & CBR method of flexible pavement design. Analysis of load
& temperature stresses of rigid pavement, joints. (5)
Unit – III
5. Materials Subgrade Soil AASHO Classification, group Index, Subgrade soil Stabilization. CBR,
aggregates Physical and mechanical properties & tests  Bituminous materials classification sources
properties and tests. Cutback & Emulsions, IRC/IS Standards, Introduction to Geotextiles.(5)
6. Construction & Maintenance
IRC,MOST specifications for quality & quantity of materials, techniques, tools and plant, for
the Earthwork, sub base, base and wearing/ surfacing course of flexible pavements with gravel,
WEM, stabilized Bituminous & Concrete as Construction material, Drainage, shoulders, rob
oriculture maintenance & repairs, Choice of construction. (5)
16
SECTIONB
Bridges
General:
UnitIV
7. General: Components, classification and identification, Data Collection site selection. Economic
Span.(3)
8. Hydrology:
Estimation of flood, discharge, water way,scour depth,depth of foundation, Afflux, clearance and
free board. (5)
Unit V
9. Loads,Forces,Stresses:
IRC Specification & code of practices, Critical combinations. (4)
10. SubStructure:
(A) Types of foundations & their choice,estimation of BC of foundation strata,Open,Pile and well
foundation,pneumatic Caissions,cofferdams. (6)
(B) Abutment, Piers & Wingwalls Their types general design principles (empirical),Choice. (2)
UnitVI
11. Super Structure:
Different structural forms culverts,causeways, minor and major bridges, suitability and choice
precost post tensioned and segmental construction. Launching, operation systems, Bearings,
Architecture. (4)
12. Rating and Maintenance:
Methods & Techniques of rating of existing bridges Inspection, Repairs, maintenance, corrosion
causes and prevention, Aesthetics .(4)
Practicals:
(A) Every student must carry minimum of 10(Ten)experiments from the following:
(a) Subgrade Soil: Classification,group index and rating CBR test(Vide IS:2720)
(b) Aggregates:Specific Gravity Water absorption flankiness index Impact, crushing and Abrasion
value tests.Petrographic identification (Vide IS:2386)
(c) Bitumen: Penetration , Softening Point , flash point, Ductility, Stripping, Viscosity of Tar &
Cutback.
(d) Students should be familiar with relevant BIS,IRC MOSt specifications of various materials for
different constructions.
(B) At least one field vist & its report in journal.
17
5CE05/ 5ST05 : BULDING DESIGN & DRAWING (1L+4D)
UNITI
1. Introduction:
Importance of Building drawing as Engineer's Language in construction & costing.
UNITII
2. Method of Drawing:
Selection of scales for various drawings, Thickness of lines, Dimensioning, Combined First angle and
Third angle method of projection, Abbreviations and conventional representations as per IS 1962.
(i) Free hand dimensioned sketches of various building elements. Importance in Civil Engineering.
(ii  a ) Developing working drawings to scale as per I.S. 962 from the given sketch design and general
specifications for terraced and pitched roofs.
(ii  b ) Developing submission drawings to scale with location site and block plan complete.
UNITIII
3. Designing of Buildings :
Introduction : Site requirements, requirements of owner and Building byelaws. Climate and design
consideration, orientation, recommendations of CBRI, Roorki and general principles of planning with
emphasis on functional planning. Graph paper design (line plans) based on various requirements for
residential, public, education and industrial buildings.
UNITIV
4. Two point perspective of Residential building neglecting small elements of building such as plinth
offset, chajja projections etc.
SESSIONAL WORK :
1. Working drawing of residential single storied building of terrace and pitched roofs with foundation
plan of load bearing structure. (Two assignment)
2. Submission drawing of single storied residential building( framed structure) with access to terrace
including all details and statements as per the local byelaws. (One assignment A1 sheet)
3. Working drawing of multistoried Public/ Educational/ Health/ Community/ Industrial building
including structural details and layout of services. (One assignment)
4. Two point perspective of the single storied Residential building neglecting small building elements. (
Two assignment – pitched & terraced roof)
5. Minimum 30 free hand self explanatory dimensioned sketches of various building elements in sketch
book.
6. Line plans of various types of buildings e.g. public/ educational/ industrial/ hospital/ community on
graph papers(04 assignments)
7. Submission drawing of 02 storied residential building framed structure including all details and
statements as per the local bye laws.
8. One compulsory field exercise.
18
5CE06 \ 5ST06 PROJECT MANAGEMENT (3L+1T)
SECTION  A
I. ENGINEERING ECONOMICS :
UNIT  I
1. Nature and scope of Economics and relationship with Engineering. [3]
2. Demand analysis : Law of demand, Elasticity of Demand, Demand Forecasting [4]
3. Production : Meaning and Factors of Production, Law of return, economics of scale location of
Industries [5]
UNIT  II
4. Cost analysis : Fixed and variable cost, Prime and supplementary costs, Average and marginal cost,
methods of allocation of overhead costs [5]
5. Money and banking : Functions of money, functions of Commercial and central Banks, Foreign
investments. [3]
6. Various types of Markets and price determination under these market conditions, scope of
Privatisation in India. [4]
SECTION  B
II. Project Planning and Management
UNIT  III
1. Introduction : Project Management, Types of Projects, Various phases of Project, Project proposal,
Components of planning, Objectives of planning, factors effecting planning, organisational
setup, establishment of premises and site organisation programme. [2]
2. Job Planning : Bar diagrams and bar charts, C.P.M., activity identification computation of
activity time, network preparation and analysis. Logical and other constraints, project duration,
floats and slacks. Ladder construction. P.E.R.T. : Event identification, event time, network
preparation and analysis, precedence network, network and cost interaction. Optimisation of project
cost. Cost slope concept and simple compression calculation. [5]
UNIT  IV
3. Resource Planning, Resource Allocation, Resource leveling, Resourcebased Net work. [3]
4. System approach, system formation, effectiveness and control, general principles of quality control
measurements and achievements. [3]
5. Planning for safety: construction hazards, safety in construction, industry and at work site.
National safety council, Safety organisation, accidents, its cost, cause, types and preventions,
losses, during natural calamities, floods and fire, and methods to reduce them. [3]
19
UNIT  V
6. Management Information System: System approach to management, Management and systems.
Inference Techniques – Use of various statistical methods and tests, graphical representation.
7. Material Management : Functions, objectives, purchasing, procedures, records, stock taking, inventory
control, ABC analysis, storing. [3]
8. Equipment management : Classification of Construction equipments, factors effecting selection,
Operation and Maintenance cost, Depreciation and Replacement cost,Economic life,down time
cost,cost of owning equipment. [3]
UNIT  VI
9. Equipments of Major Projects : Excavating machines such as : Power shovels, Drag Line,
Bulldozer, Scraper, Drilling and Blasting Equipments, Material Transporting and handling
equipment such as Cranes, Hoists, conveyer belts, dumpers, cableways, rail system (Size,
performance and limitations) [5]
10. Concrete equipments : Different types of mixers Vibrators, batch mixing plants, transportation of
concrete, concrete pumps and placers. Guniting and its equipment. [4]
SELECT REFERENCE BOOKS:
1. Construction Management Peurifoy
2. CPM and PERT L. Srinath
3. Project Management Roy Choudhary
4. Equipment Management – Mahesh Verma
Question paper pattern :
Section A : Two questions (14 marks each )are to be solved out of three
Section B : Four questions (13 marks each )are to be solved out of six
5CE07 S ITE VISITS (3P)
3 Practical hours (College Assessment) Marks : Grade Students should be taken for visit to various
Civil Engineering construction sites such as R.C.C. Structures, Steel Structures, Bridges, culverts,
Hydraulic Structures, watertanks, Roadworks, Railways, Watersupply and Sanitary works,
Geotechnical Exploration, Maintenance and Rehabilitation works, Irrigation systems, Formwork,
Reconnaissance and Detailed Surveying & levelling etc. Minimum Five visits are expected. Students
should submit a detailed report on the visit duly approved by the concerned teacher.
The Detailed Report should mainly consist of the following: 
1. Name of Construction Site with address
2. Nature of construction work and various structural components
3. Nature of ownership, executing and supervising authority
4. Architect and Structural Engineer
5. Architectural concept and Design features
6. Commencement of the work and tentative completion
7. Present Status of work
8. Estimated cost of the work ( Money spent till date)
9. Mode of availability of finance
10. Various types of manpower for the work
11. Various safety measures and amenities provided to manpower
12. Various construction equipments for the work
13. Various materials used for the work
20
14. CPM / PERT of the project
15. Type of inventory control
16. Resource planning implemented
17. Social benefits and implication
18. Safety measures during and posts construction
19. Post Construction Maintenance provisions
20. Effect on environmental aspect and sustainable development
21. Various of scaffolding, Formwork, lifting devices
22. Site of precast units for the work and its mode of transportation
23. Use of local available material like flyash, slag, silicafumes, etc.
24. Clauses for delay / faulty construction
25. Clause for Arbitration
VI SEMESTER B.E. CIVIL
6CE01 / 6ST01 Structural Analysis II
(3L + 1T + 2P)
SECTIONA
UNITI
1. Kani’s Method applied to symmetrical and unsymmetrical frames with sway (Up to single bay Two storey)
UNITII
2. Approximate method of Structural analysis for multistoreyed frames with lateral loads (Portal and Cantilever
method), Approximate methods for vertical loads i.e. Substitute frame method etc. (Max three bay three storey)
UNITIII
3. Column Analogy method, Applications to beams, Calculations of Stiffness factors and carry over factors for
nonprismatic method, Analysis of nonprismatic fixed beams.
SECTIONB
UNITIV
4. a) Introduction to Flexibility Method of structural analysis, influence coefficients, Choice of base determinate
structure and redundant forces, compatibility equations. Hand solution of simple beam problems.
b) Moment distribution applied to frames with sway(upto single storey two bay)
UNITV
5. Strain energy method applied to simple composite structures (Simple problems), Introduction to basic theory of
elasticity, Concept of stress, strains, strain displacement relationship, equation of equilibrium, boundary
conditions, generalized Hooks low, plane stress and plane strain problems.
21
UNITVI
6. Theory of photoelasticity applicable to beams. Study of various types of strain gauges , Analysis of strains by
strain Guages.
(VI01)
PRACTICALS:
Minimum TEN of the following :
1. To find the slope & deflection of continuous beam.
2. To find the value of Flexural rigidity (EI) for a given beams & compare with theoretical value.
3. To determine the moment required to produce a given rotation at one end of a beam when the other end is i)
Pinned ii) Fixed
4. To study the behavior of different types of struts and to calculate the Eulers Buckling load for each case.
5. To verify the Maxwell’s reciprocal theorem for beam.
6. To measure the strain in the cantilever beam with the help of acoustic strain gauge.
7. Study of various types of strain gauges.
8. Plotting of influence lines by making use of MullerBreslau principle.
9. Determination of deflection of trusses by WillotMohrs diagram.
10. Determination of material fringe value.
11. Determination of stress in beam by photoelastic method.
12. To find horizontal thrust and to draw the influence line for horizontal thrust for two hinge arch.
13. To calculate horizontal deflection at roller end in two hinged arch.
14. To measure the strain in the cantilever beam with the help of electrical resistance strain gauge.
15. To determine horizontal thrust for indeterminate portal frame
16. Study of Poloriscope
References:
1. C K Wang, ‘Intermediate Structural Analysis’
2. S P Timoshenko, ‘Theory of Structure’
3. Jain, Jai krishna, ‘Plain and Reinforced concrete Structures’, Vol.II
4. S P Timoshenko, ‘Theory of Elasticity’
5. Rally & Dally ,‘Experimental Stress Analysis’
22
6C02/6ST03 RCC STRUCTURES 3(L)+1(T)+2(D)
SECTION A
(Four question of 10 marks are to be answered out Six questions of 10 marks each to be set on Units I to
IV)
Unit – I
1. Introduction to the Working Stress Method of RCC design. Basic concepts in design for flexure,
assumptions, design constants. Analysis of the rectangular section. Balanced, underreinforced and
overreinforced sections. Drawbacks and limitations of Working stress method. (3)
2. Prestressed Concrete : Properties of high grade materials, concepts of prestressed concrete, methods of
prestressing, losses in prestressing. Various systems for prestressing with particular reference to
Freyssinet, Magnel Blatton and Gifford Udall systems. Analysis of rectangular, T and I section.
(3)
Unit – II
3. Introduction to Limit State Design: Concept of probabilistic design and limit state design.
Characteristic values, partial safety factors, stress strain relationship stress block parameters, failure
criteria, types and properties of reinforcement, limit state of Serviceability and limit state of collapse.
Other limit states. Review of IS – 456 2000. (2)
4. Limit state of collapse in flexure: Analysis and design of singly reinforced rectangular section.
Balanced failure mode, primary tension failure mode and primary compression failure mode.
Unit – III
6. Limit state of Collapse in Flexure: Analysis & Design of the Tee & Lbeam section. (3)
7. Limit state of collapse in compression: Analysis & design of short axially loaded column. Columns
subjected to uniaxial bending, use of interaction curves. (3)
Unit – IV
8. Limit state of Collapse in Shear & Bond: Design of beam for shear, shear span, post cracking
resistance, shear mechanism approach, shear failure modes and collapse loads, interaction of shear,
flexure and axial force, Check for bond. (3)
9. Limit state of Serviceability :
(i) Causes and control of cracking: Crack in plastic concrete at early age, Cracks due to temperature
and shrinkage, restrain induced cracks, Cracks due to loading. Needs for crackwidth control.
(ii) Moment curvature relationship, deflection control of beams and one way slabs. (no numerical
calculations) (2)
23
SECTION B
(Two questions of 20 marks are to be answered out of Three questions of 20 marks each to be set on Units
V and VI)
Unit – V (with WSM)
10. Design of circular water tank with roof slab/ dome resting on ground by Approximate methods/ IS
code method. (4)
11. Design of rectangular water tank with oneway roof slab resting on ground by approximate method/ IS
code method. (4)
12. Design of prestressed slab/ rectangular beam. (2)
Unit VI (with LSM)
13. Design of oneway, simply supported, single span and cantilever slabs, and continuos slab/ beam with
IS coefficients. (4)
14. Design of rectangular pad / slopped footing for axial load. (3)
15. Design of Doglegged and Open Well Staircases (4)
PRACTICALS
Practical shall consist of minimum Four design assignments with detailed drawing on A2 size sheets and
detailed calculations in journal.
i) Circular water tank with roof slab/dome resting on ground.
ii) Rectangular water tank with oneway roof slab resting on ground.
iii) Single span prestressed concrete rectangular beam, slab.
iv) Oneway slab, continuous slab.
v) Rectangular pad / slopped footing.
vi) Dog legged / Open well staircase.
vii) One field visit and its report in the journal.
6CE03 : GEOTECHNICAL ENGINEERINGII (3L+1T)
SECTIONA
UnitI:
GEOTECHNICAL EXPLORATION:
Importance and objectives of field exploration, principal methods of subsurface exploration, open pits &
shafts, types of boring, number, location and depth of boring for different structures, type of soil samples &
samplers. Principles of design of samplers, collection & shipment of samples, boring and sampling record.
Standard penetration test, corrections to Nvalues & correlation for obtaining design soil parameters. (6)
UnitII:
STABILITY OF SLOPES:
Causes and types of slope failure, stability analysis of infinite slopes and finite slopes ,φcenter of critical slip
circle, slices method for homogeneous cφ soil slopes with pore pressure consideration. Taylor’s stability
numbers &stability charts, methods of improving stability of slopes, types, selection and design of graded
filters.(7)
UnitIII:
LATERAL EARTH PRESSURE:
Earth pressure at rest, active & passive pressure, General & local states of plastic equilibrium in soil.
Rankine’s and Coulomb’s theories for earth pressure. Effects of surcharge, submergence. Rebhann’s criteria
for active earth pressure. Graphical construction by Poncelet and Culman for simple cases of wallsoil system
for active pressure condition. (8)
24
SECTIONB
UNITIV:
GROUND IMPROVEMENT:
Methods of soil stabilization use of admixtures (lime, cement, flyash) in stabilization. Basic concepts of
reinforced earth, use of geosynthetic materials Salient features, function and applications of various
geosynthetic materials. Vibroflotation, sand drain installation, preloading. (5)
UNITV
SHALLOW FOUNDATIONS:
Bearing capacity of soils: Terzaghi’s theory, its validity and limitations, bearing capacity factors, types
ofshear failure in foundation soil, effect of water table on bearing capacity, correction factors for shape and
depth of footings. Bearing capacity estimation from Nvalue, factors affecting bearing capacity,
presumptive bearing capacity.
Settlement of shallow foundation: causes of settlement, elastic and consolidation settlement, differential
settlement, control of excessive settlement. Proportioning the footings for equal settlement. Plate load test:
Procedure, interpretation for bearing capacity and settlement prediction. (8)
UNITVI
PILE FOUNDATION:
Classification of piles, constructional features of castinsitu & pre cast concrete piles. Pile driving methods,
effect of pile driving on ground. Load transfer mechanism of axially loaded piles. Pile capacity by static
formula & dynamic formulae, pile load test and interpretation of data ,group action in piles, spacing of piles in
groups, group efficiency, overlapping of stresses. settlement of pile group by simple approach, negative skin
friction and its effect on pile capacity ,general feature of under reamed piles. _ (8)
Books:
1) Arora K.R : Soil Mechanics & Foundation Engineering.
2) Punmia B C : Soil Mechanics & Foundations
3) Gopal Ranjan & Rao : Basic & Applied Soil Mechanics
4) P Raj : Geotechnical Engineer
6CE04 FLUID MECHANICSII (3L+1T+2P)
SECTIONA
UNITI
1. LAMINAR FLOW:(03)
Steady uniform laminar flow in circular pipes; Velocity and shear stress distribution; HagenPoiseuille
equation.
2. BOUNDARY LAYER THEORY: (04)
Nominal thickness, displacement thickness, momentum thickness of the boundary layer: Boundary
layer along a long thin plate and it’s characteristics; Laminar boundary layer; turbulent boundary layer;
laminar sublayer: Separation of boundary layer on plane and curved surfaces.
3. REAL,INCOMPRESSIBLE FLUID FLOW AROUND IMMERSED BODIES: (04)
In general definition of drag and lift; Flow past plates, cylinders and spheres; drag on sphere, cylinder
and flat plate.
25
UNITII
4. FLOW THROUGH PIPES: (10)
Hydraulically smooth and rough pipes; Frictional resistance to flow of fluid in smooth and rough
pipes; Nikurade’s experiment; Moody’s chart; DarcyWeisbach & Hazen William’s equation for
frictional head loss; Hydraulic gradient and energy gradient: Pipes in series and parallel; Branched
pipes; Siphon; transmission of power through pipes; HardyCross method of pipe networks;
Waterhammer pressure head due to sudden closure of valve.
UNITIII
5. FLOW THROUGH OPEN CHANNEL:
(A) GENERAL: (01)
Types of channel and their geometrical properties; Types of flow in open channel
(B) UNIFORM FLOW: (05)
Chezy’s and Manning’s equations;Hydraulically most efficient rectangular, triangular and trapeziodal
sections; Computations of normal depth of flow ,conveyance of channel,section factor for uniform flow,
normal slope and normal discharge.
(C) CRITICAL FLOW:(04)
Specific enery and it’s diagram;alternate depths;Computations of critical depth, section factor for critical
flow ,critical slope ;normal critical slope;Specific force and it’s diagram;Conditions of critical flow.
SECTIONB
UNITIV
(A) APPLICATIONS OF SPECIFIC ENERY ,GRADUAL TRANSITIONS OF
CHANNELS.(02)
(B) GRADUALLY VARIED FLOW: (05)
Dynamic equation for GVF; Classification and characteristics of surface profiles; Direct Step method of
computing profile length.
(C) RAPIDLY VARIED FLOW : (03)
Defination of hydraulic jump; Equation of hydraulic jump in horizontal rectangular channel; Length &
heigth of jump; Energy loss in jump; Classifications of jump.
UNITV
6. HYDRAULIC MODELS: (05)
Difference between model and prototype;Similitude type of similarities; Model laws Reynolds model law
and Froude model law; Types of model distorted, undistorted; Froude’s method of determining resistance
to partially submerged objects like ship.
7. FLUID MACHINERY:
(A) Impact of Jet stationary and moving curved vanes.(02)
(B) TURBINES: (03)
Definition: Gross and net heads; different efficiencies; Classification of turbines;component parts and
working principles;selection of turbines on the basis of head and specific speed.
26
UNITVI
8. Centrifugal and Reciprocating Pumps
(A) CENTRIFUGAL PUMP: (06)
Component parts; Working principle; Static and manometric heads;different efficiencies; Specific speed;
Theoretical aspects of multistage pump, pump in parallel; Priming devices; Trouble & remedies; Main &
operating characteristics curves.Selection on basis of operating characteristics.
RECIPROCATING PUMPS: (03)
Components parts, Working principle, Work done of single & double acting pumps;Negative slip, Air
vessels – Working principle and necessity.
6CE04 FLUID MECHANICSII (3L+1T+2P)
PRACTICALS:
Minimum TEN practicals, from the list given below shall be performed:
1. Study of flow around immersed bodies.
2. Determination of DarcyWeisbach friction factor for given pipes.
3. Determination of Manning’s or Chezy’s constant for an open channel.
4. Developing specific energy diagram for a rectangular channel.
5. Study of GVF profiles.
6. Study of hydraulic jump in a horizontal rectangular channel.
7. Study and performance of Francis turbine.
8. Study and performance of Pelton Wheel turbine.
9. Study and performance of Centrifugal pump.
10. Study and performance of Reciprocating pump.
11. Design problem on pipe network analysis.
Recommended books
:
1. Hydraulics & Fluid Mechanics Dr.Modi & Dr. Seth
2. Fluid MechanicsStreeter & Wylie
3. Fluid Mechanics Dr. A.K.Jain
4. Fluid Mechanics through problems Garde
5. Theory and applications of Fluid Mechanics K. Subramanya
6. Foundation of Fluid MechanicsYuan
7. Flow through open channel – K.G.Rangaraju.
27
6CE05/ 6ST06 COMPUTER APPLICATION IN CIVIL ENGINEERING
(3L + 1T + 4P)
SECTIONA
UNITI Introduction
CFundamentals,CHARACTER SET data type constants and variables, Declaration of constants &
variables, Expression, Statements, Symbolic constants. Operator and Expression, Arithmetic operator
Unary operator, Relational and Logical operator, Assignment operators, the conditional operator, Library
functions. Data Input & output Interactive programming preparing & running a complete simple program.
UNITII Control Statements
Control statement, the WHILE statements, dowhile, for nested loop, ifelse, switch break, continue, goto
statement, comma operator.
UNITIII Advance Topics
Functions, storage class, Arrays, Pointers, structures and Unions, Data files, File Handling, Link list.
SECTIONB
UNITIV
1. Fundamental of Numerical Methods, Interpolation & extrapolation. Numerical Integration
(Simpson’s method, Trapezoidal method, Newton Gauss quadrature method), Interactive Computer
Program Development
UNITV
2. Solution of linear Algebraic Equations, Gauss elimination, Cholesky method), solution errors.
Interactive Computer Program Development
UNITVI
3. Solution of non Linear Equations (Newton Raphson schemes), Initial & Two point boundary value
problem, Euler's, Rungekutta, Milne's etc, Interactive Computer Program Development
Practical : Minimum Sixteen Computer program development min. one from each of the following field
using FORTRAN95 / C language . Atleast two programs on mixed language i.e. using both FORTRAN95
and C and four programs in any one language. It is recommended to have atleast four programs based on
Numericals methods in either Fortran or C and Two assignments in application software’s such as spread
sheets, database management programs etc.
1. Engineering Mechanics
2. Strength of Material
3. Transportation Engineering
4. Geotechnical Engineering
5. Hydraulic Engineering
6. Irrigation and Water Resource Engineering
7. Surveying
8. Estimating and Costing
9. Structural Analysis
10. Structural Design
11. Environmental Engineering
12. Matrix algebra, Solution Techniques
13. Numerical Integration
14. Table generation from IS:456
15. Earthquake force calculation on structures as per IS:1893
28
References:
1. Schildt, ‘The complete reference C’
2. Balagurusamy ,‘Programming with C ‘
3. Ramkumar ,‘Programming with C ‘
4. Gottfried,‘Programming with C ‘
5. Rajaraman ,‘Programming with Fortran 90/95 ‘
6. Digital Fortran Manual
7. Lahey’s Fortran Manual
6CE06 TECHNICAL WRITING (3P)
1.
Reading strategies
: Practice in various reading techniques, skimming, scanning , eye reading etc.
Active and passive reading and interpreting charts and diagrams  Need and role of reading in
technical/Industrial organization.
2.
Return Communication
: Introduction to technical writing  Discourse writing : Definition ,Description
. Instructions  Summary writing  cohesive paragraphs.
3.
Business Communication
: Business correspondence  format , tone and massage of business letters 
prospective / point of view in purposive writing  sales letters.
4.
Listening & language developments
: Barriers to listening : Physical and psychological  steps to
overcome them  listening with a propose  active listening and anticipating the speaker  precise in
note  taking  steps to improve speaker's contribution.
5.
Successful speaking techniques
: How to improve self  expression  Need for clear thinking  The
speech process  Fluency and Accuracy in speech  Developing persuasive speaking skills  Goal
oriented group discussion  Formal and public speaking practice.
REFERENCES:
1. Alan Maley and Sandra Moulding , Learning to listen  Task for developing listening skills ,
Cambridge University Press , 1981.
2. Deborah C. Andrews, Margaret D. Blickle, Technical writing : Principle and forms , Macmillan 1978.
3. Eric H. Glendinning and Beverly Holmstrom, Study reading  A course in reading for academic
purpose, Cambridge University Press 1992.
4. John Kirkman , Good style  Writing for Science and Technology, E and FN spon , an imprint of
chapman anf Hall 1992.
5. List hamplyoms , Benheasley, Study writing , Cambridge University Press , 1987.
6. Louis Trimple, English for Science and technology  A discourse approach , Cambridge University
Press 1985.
7. Patric Hanks , Gim Corbett, Business listening tasks, Cambridge University Press 1986.
8. Sharon Bower, Painless/speaking, Thorsons 1990.
9. Stewart Zimmer and Camp., College English and communication , Macraw Hill, 1987.
10. Tom Hutchinson , Alan Waters , English for specific purpose, Cambridge University Press 1987.
29
VII Semester B.E.(Civil)
7CE01/7ST01 Structural AnalysisIII (4L + 1 T + 2 P)
SECTIONA
UNITI
1. Basic concept, Degree of Freedom,Basic concept of Direct Stiffness Method. Formulation of elemental/local
stiffness matrix and global stiffness matrix for plain truss. Transformation Matrix, Assembly of Global /
Structure stiffness matrix up to (8x8). Member load matrix, Assembly of Global / Structure load matrix
,Solution to problems with maximum degree of freedom four.
UNITII
2. Formulation of element / local stiffness matrix and global stiffness matrix for Beam members (without axial
deformations) for continuous beams,Transformation matrix Assembly of global / structure stiffness matrix,
Member load matrix due to concentrated loads, uniformly distributed Loads ,Moments Assembly of global/
structure load matrix up to (8x8) Solution to problems with maximum degree of freedom four.
UNITIII
3. Formulation of element / local stiffness matrix and global stiffness matrix for Plane Frame member (With axial
deformation), Transformation Matrix, Assembly of global / structure stiffness matrix, Member load matrix due
to concentrated loads, uniformly distributed Loads , moments, Assembly of global/ structure load matrix.
Solution to plane frame problems with maximum degree of freedom six, Inclined member problems.
SECTIONB
UNITIV
4. Formulation of element / local stiffness matrix and global stiffness matrix for Plane Grid transformation
Matrix, Assembly of global / structure stiffness matrix, Member load matrix due to concentrated loads,
uniformly distributed Loads , moments, Assembly of global/ structure load matrix. Solution to problems with
maximum degree of freedom six.
UNITV
5. Analysis of Member for temperature loading, initial joint displacement (sinking of support), lack of fit in
trusses, trusses with inclined roller, storing of global / structure stiffness Matrix, full storage, banded storage,
band Mininisation
UNITVI
6. Introduction to finite Element method, basic concepts, discretisation of structure, Rayleigh Ritz member for bar
elements (prismatic/ Non prismatic) Displacement based Bar elements (prismatic/ Non prismatic) and Bean
elements (prismatic), Load Matrix for body forces.
Note
: There shall be one question with 4 DOF & rest with 3DOF.
PRACTICAL:
Minimum Eight Problems, on complete syllabus with hand calculations using scientific calculators and also solution
to same problems by using available readymade software. (Solution is restricted to four degree of freedom problems
and assembly restricted to eight degree of freedom problems)
BOOKS:
1. Matrix Method of Structural Analysis  Gere and Weaver
2. Computer Analysis of Structures  Beaufait, Rowen, Headly et al
3. Computer Analysis of Structures  Flemmings
4. Computational Structural Mechanics, S Rajasekaran & G Sankarasubramanian
5. Finite Element Method – R D Cook
30
7CE02/7ST02 ADVANCED CONCRETE STRUCTURES (3L+1T+4P/D)
SECTION A
( Three question of 13/14 marks are to be answered out of Five questions of 13 marksone question of 14
marks – to be set on Units I to III )
Unit – I
1. Limit state of collapse in flexure : Analysis and design of doubly reinforced rectangular, Tee and L
sections. (4)
2. Limit state of collapse in torsion : Concept of interaction of torsion, shear and flexure. Analysis and
design of rectangular section for torsion, shear and flexure. (3)
3. Limit state of serviceability : Deflection calculations for beams and oneway slabs. (3)
Unit – II
4. Analysis and design of columns subjected to biaxial moments. Design of long columns. (5)
5. Design of Isolated footing , for uniaxial and Biaxial bending. For Square , Rectangular & Circular.
(5)
Unit – III
6. Moment redistribution :Analysis and Design of fixed beam, propped cantilever, twospan symmetric
continuous beam. (10)
SECTION B
(Two question of 20 marks are to be answered out of Three questions of 20 marks each to be set on Units
IV and V )
UnitIV (with LSM)
7. Analysis and design of portal frames ( single bay single storey) hinged or fixed at base. Design of
hinge and design of foundation. (5)
8. Design of combined footing (10)
i) Rectangular footing.
ii) Strap beam footing.
iii) Trapezoidal footing.
iv) Raft footing.
Unit – V ( with LSM )
9. Design of RCC Two way slab with various end conditions using with IS Code coeff.
(5)
10. Design of R.C.C. Cantilever and counterfort Retaining wall (10)
PRACTICALS
Practical work shall consist of
1. Design assignments with detailed drawing on A2 size sheets and detailed calculations in journal.
i) Two way slab with various end conditions.
ii) Cantilever/ Counterfort retaining wall.
iii) Combined footing.
iv) Portal frame.
2. One field visit & its report in journal.
31
7CE03 IRRIGATION ENGINEERING (3L+1T+2P)
SECTIONA
UNITI
1. GENERAL: (03)
Necessity and importance of Irrigation Engineering;Benefits & ill effects of Irrigation;Classification of
Irrigation;General principles of flow,lift,perennial, inundation Irrigation systems;Comparative study of
sprinkler and drip Irrigation systems.
2. WATER REQUIREMENTOF CROPS: (07)
Suitability of soils for Irrigation ;Standards of irrigation water;PETR method of crop water
requirements;Depth and frequency of irrigation;definations of field capacity,wilting point, available
moisture,duty,delta,GCA,CCA,kor depth,base period,outlet factor ,capacity factor,time factor,root zone
depth: Relation between duty and delta; Factors affecting duty; Principal crops in India;Crop
rotation;Methods of assesssment of irrigation water .
UNITII
3. RESERVOIR PLANNING: (06)
Selection of site for Reservoirs; Enginering surveys,Geological and Hydrological Investigations;Fixing of
LWL,FTL,TBL,HFL;Different storage zones in reservoir; Determination of storage capacity by mass
curve method; Reservoir sedimentation; Life estimation of reservoir by Brune’s method; Organisation &
Administration of Irrigation projects.
4. DAMS:
(A) GENERAL: (01)
Classification of dams as per use , hydraulic design and materials; Factors governing selection of type of
dams.
UNITIII
(B) GRAVITY DAM: (06)
Definition; forces acting on gravity dam; stability requirements; Theoretical & practical profile of gravity
dam; Low & High dam;Galleries.
(C) EARTHEN DAMS: (06)
Types of earthen dam; Description of component parts of earthen damsfoundation, cut off trench,rock toe,
hearting, central impervious core, pitching and chipping, turfing; Seepage through body of earthen dam and
drainage arrengements; Failure Of earthen dams; Plotting of phreatic line for homogeneous earthen dams
with horizontal filters ; Stability of foundation against shear.
SECTIONB
UNITIV
5. SPILLWAYS: (05)
Types of spillway with their working operations; General principle of design of ogee spillway; Spillway
gates vertical lift, radial , rolling and drum; Energy dissipation methods d/s of spillways.
6. DIVERSION HEAD WORKS: (07)
Component parts of diversion headworks – Fish ladder ,guide wall, devide all, silt excluder and silt ejector;
Causes of failure of weirs on permeable foundation; Bligh’s Creep theory; dr. Khosla’s theory for design of
wiers on permeable foundations.
32
UNITV
7. CANALS:
(A) GENERAL: (02)
Types of canal; Alignments of canal; Cross section of Irrigation canals; Balancing depth; Schedule of area
statistics; Losses in canals
(B) CANALS IN ALLUVIAL SOILS: (05)
Kennedy’s silt theory – Design procedure ,silt supporting capacity, drawbacks; Lacey’s silt theory
Definition of initial final and permenent regime channels, Lacey’s Regime equation, channel design
procedure, drawbacks; Garret’s diagram for channel design.
(C) LINED CANALS: (03)
Design procedure; Types of lining; relative merits and demerits of canal lining;
Economics of canal lining.
UNITVI
8. CANAL STRUCTURES:
(A) CANAL REGULATION WORKS: (03)
Only theoretical aspects of location, objects, classification ,components and schematic section of Head
Regulator, Cross regulators, canal escapes, Canal falls and canal outlets.
(B) CROSS DRAINAGE WORKS : (02)
Only theoretical aspects of location , objects, classfication, components and schematic section of aqueducts,
siphon aqueducts, super passege, canal siphon, inlets outlets and level crossings.
9. WATER LOGGING AND LAND DRAINAGE: (03)
Causes, effects, preventive measures of water logging, Types of drains, Layout of tile drains system; flow
of ground water to drains.
10. RIVER TRAINING WORKS: (02)
Defination; Classification; theoretical aspects of river training works like as Guide banks, Groynes and
Spurs, Bank protection.
PRACTICALS:
Following Designs and Drawing should be included (Minimum Five)
1. Reservoir Planning Capacity of reservoir.
2. Life of Reservoir
3. Gravity Dam – Checking of various modes.
4. Earthen Dam – Phreatic Line , checking of foundation against shear
5. Design of canals (Lined and Unlined)
6. Design of Lift Irrigation Scheme.
7. Drawing of various canal structures.
8. Site visit to irrigation project – Detail report should be submitted.
Recommended Books:
1. Irrigation Engineering and Hydraulic Structures Santosh Kumar Garg
2. Irrigation Engineering and Hydraulic Structures S.R. Sahastrabudhe
3. Irrigation Engineering and Water Power Engineering B.C. Punmia
4. Irrigation Engineering and Hydraulic Structures K.R.Arora
5. Irrigation Engineering N.N. Basak
6. Irrigation Engineering and Hydraulic StructuresR.K.Sharma
7. Irrigation Engineering G.L. Asawa
8. Water Resource Engineering Principles and PracticeC.S. Murty
9. Water Resources and Irrigation Engineering P.N. Modi
33
7CE04 MAINTENANCE AND REHABILETATION OF CIVIL
ENGINEERING STRUCTURES (3L+1T)
SECTIONA
UNIT – I
1. INTRODUCTION :
Deterioration of structures. Definition of maintenance, Need for maintenance of different Civil
Engineering structures. Maintenance characteristics that influence maintenance needs. A study of the
cause of neglect and poor maintenance of structure. Measure of maintenance. [3]
2. CLASSIFICATION OF MAINTENANCE WORK :
Servicing, rectification, replacement, planned, unplanned, preventive, corrective, predictable and
avoidable maintenance works. Renovation and Rehabilitation. [3]
3. COMMON MAINTENANCE PROBLEMS :
Relating to various Civil Engineering Structures and systems. Technology of maintenance. Area prone
to frequent maintenance. Causes that aggravate maintenance work like high rise buildings. Special
construction methods, new materials, difficult accessibility, Environment etc. [4]
UNIT – II
4. FACTORS AFFECTING INCIDENCE AND MAGNITUDE OF MAINTENANCE WORK :
Over loading, movement of grounds, temperature variations, moisture leakages and dampness, chemical
actions and corrosion, growth of trees, earthquake, flood and fire, riots and vandalism. Design defects.
Defects in construction and use of materials, choice of materials for durability and maintainability.
Design, expose and other factors effecting durability, precautions to increase durability. [5]
5. Inspection, Identification and diagnosis of Common defects and failures with possible causes
inbuildings, Roads, Bridges, Railway Tracks, Canals and C.D.Works, Tunnels and Special Structures
like Service Reservoirs, Water Supply, Sewerage, Storm water Drains, [5]
UNIT – III
5. PREVENTIVE MAINTENANCE :
General  Site selection, choice of structural systems and materials, specifications & detailing.
Buildings Special attention to foundations, wells, roofs, terraces, floors, doors and windows, plinth,
compound walls,
expansion joints stair cases to improve maintainability. Pumping and sanitary works. Termite control.
External finishes. Roads Stabilization techniques, compaction and drainage, slope protection, joints in
C.C. Pavements, Routine and service maintenance. Bridges and C.D. Works Repairs, strengthening and
rehabilitation. Service life and expected Road carrying capacity. Service and Stability requirements.Future
service requirements, loads, fatigue, creep. [10]
34
SECTIONB
UNIT – IV
6. MATERIALS AND TECHNIQUES FOR MAINTENANCE :
Materials for repairs like cement, cement grouts, epoxy grouts, mortars and coatings, polymer concrete
composites, sealants, membrane overlays, fiber reinforcement concrete, Resin based compounds,
emulsions and paints, geotextiles. Techniques like stiffening, linings, guniting, protection systems,
prestressing, Posttensioning and base isolation technology. Temporary supporting systems for Structures
like timbering, shoring etc. [5]
7. ECONOMICS OF MAINTENANCE :
The burden of maintenance work, complexity of the work and the conflicting interests involved.
Various economic factors that affect maintenance work. Initial and user costs. Impact of inflation on
maintenance. Life of structures : Structural life and economic life. Basics of life cycle costing
Techniques. [5]
UNIT  V
8. MAINTENANCE PLANNING :
The deeper significance of maintenance as opposed to cosmetic treatments. Broad action plan,
Enter the password to open this PDF file:
File name:

File size:

Title:

Author:

Subject:

Keywords:

Creation Date:

Modification Date:

Creator:

PDF Producer:

PDF Version:

Page Count:

Preparing document for printing…
0%
Commentaires 0
Connectezvous pour poster un commentaire