Mega Type Series Booklet - Printversion 08-05

scaredbaconSoftware and s/w Development

Jul 4, 2012 (5 years and 1 month ago)

3,587 views

Mega
Type Series Booklet
Centrifugal Pump
Application
The KSB Ajax Mega centrifugal pump is suitable for handling
water, condensate, oil, some aggressive chemical products
and other liquids mainly used in the following applications:

Water supply

Irrigation

Air conditioning

Fire fighting

Drainage

Heating

Chemical and petrochemical

Sugar and alcohol industry

Boiler feed

Auxilary circuits in refineries

Auxilary circuits in industry (paper, food, synthetic
fibres, others)
Design
Horizontal, single stage, end suction centrifugal pump dimen-
sionally built to ISO 2858 and technical specification ISO 5199.
The back pull out design allows for easy maintenance and
repair as the rotating element may be removed without dis-
turbing the pipework. Pump has wear rings as standard and
lifting eye on bearing bracket.
KSB Ajax Pumps Pty Ltd
Designation
M 80 - 160
Model / Type
Discharge diameter (mm)
Nominal impeller diameter (mm)
Operating Data
50 Hz 60 Hz
Pump sizes
Flow up to 150 L/s 175 L/s
Head up to
Temperature up to
Speed up to 2900rpm 3500rpm
32 mm to 150 mm
160
o
C
160m
Mega
2
Selection Chart
1450 RPM
Selection Chart
2900 RPM
Mega
3
Construction
Horizontal single stage, end suction with vertical discharge.
The “back pull out” design allows for the maintenance of the
pump without disturbing the pipework connected to the cas-
ing, or the pump alignment.
The pump is built to the dimensional and technical require-
ments of ISO 2858 and ISO 5199. Flanges are in accordance
with AS/NZS 4331.2, ISO 7005-2 and DIN 2533/16 Bar.
Casing
Self-venting horizontal volute casing with horizontal end suc-
tion and vertical discharge. The casing has supporting feet
and is fitted with a wear ring. The suction nozzle includes a
vane to reduce prerotation.
Shaft
The shaft is of the dry type, with protection sleeve to prevent
contact with the pumped liquid (for packed gland only). For
standard mechanical seal models the shaft is in contact with
the pumped liquid.
Bearings
Grease lubrication – Standard
Max. Pump temperature 105
o
C
The bearing arrangement consists of two deep groove ball
bearings lubricated by grease. Bearings are shielded and
greased for life.
Note: MH models have oil lubrication as standard.
Oil lubrication – Option L1
Max. Pump temperature 160
o
C
The use of oil as a bearing lubricant is available as an option.
Constant level oiler is provided to ensure optimum oil level is
maintained.
Shaft Seal
The shaft sealing is carried out by means of gland packing or
by mechanical seal.
The standard mechanical seal is a single, unbalanced, elas-
tomer bellows seal. The seal is self-aligning and automatic
adjustment compensates for abnormal shaft end play, runout
and primary seal wear. The mechanical drive eliminates over-
stressing of the elastomer bellows and the single coil spring
is not affected by a build up of solids. The seal can be re-
placed in the field to minimise downtime.
Seal operating temperature –30
o
C to +105
o
C.
Seal Materials:
Painting
KSB Ajax standard – red oxide undercoat and one coat of
industrial enamel finish coat.
Hard Faces High Pressure
Std.Option M3 Option M1
Seal O Ring Nitrile Nitrile Nitrile
Seal Face Carbon Silicon Carbide Carbon
Bellows Nitrile Nitrile Nitrile
Retainer
Drive Band 316 316 316
Spring Holder
Spring Holder
Seat Ceramic Silicon Carbide Ceramic
Accessories
Drive
The pump is only recommended for direct drive via a flexible
spacer coupling. Spacer couplings enable utilisation of the
back pull out feature.
Where belt drives are necessary a separate jack (intermedi-
ate) shaft with bearings to carry the belt loads may be re-
quired.
All drive systems, where supplied by KSB Ajax, are appropri-
ately protected by suitable guards.
Baseplate
Baseplates for electronic drives are available in a variety of
styles.
Standard:Fixed and grouted directly to the foundation.
Anti vibration:Rigid baseplate on rubber mounts.
Rigid baseplate on spring mounts.
Rigid baseplate with inertia block and spring
mounts.
Pump Selection
For pump selection the hydraulic performance curves should
be used. These curves are based on water at 15
o
C and SG
equal to 1.0.
NPSH values are indicated on the performance curves. At
least 0.5m must be added as a safety margin.
To overcome variations between actual and design system
requirements it is recommended that the driver power ex-
ceeds the absorbed pump shaft power:
Peripheral Speed
After determining the pump operating speed and checking its
maximum discharge pressure, the impeller material must
be checked to ensure that it is suitable with regards to its
peripheral speed, observing the following limits.
- Cast Iron - to 40 m/sec.
- Zinc Free Bronze - to 60 m/sec.
* Peripheral speed of 250mm diameter impellers at 3000
rpm is 39/sec.
Up to 12
Above 12
A
pprox. 30%
Approx. 20%
Approx. 10%
Shaft kW
Driver Power
Reserve
Up to 1.5
Absorbed Pump
Mega
Mechanical Seal Suction Pressure Limits At Various Speeds
Casing - Pressure / Temperature Limits
Flange Ratings - Pressure / Temperature Limits
Bearing Lubrication - Pressure / Temperature Limits
4
Std.Opt. M1 Std.Opt. M1 Std.Opt. M1 Std. Opt. M1
1000kPa 1600kPa 1000kPa 1600kPa 1000kPa 1600kPa 1000kPa 1600kPa
10 bar 16 bar 10 bar 16 bar 10 bar 16 bar 10 bar 16 bar
1000kPa 1600kPa 1000kPa 1600kPa 1000kPa 1600kPa 1000kPa 1400kPa
10 bar 16 bar 10 bar 16 bar 10 bar 16 bar 10 bar 14 bar
1000kPa 1600kPa 1000kPa 1600kPa 1000kPa 1200kPa ~ ~
10 bar 16 bar 10 bar 16 bar 10 bar 12 bar ~ ~
800kPa 800kPa 800kPa 800kPa 600kPa 600kPa ~ ~
8 bar 8 bar 8 bar 8 bar 6 bar 6 bar ~ ~
Shaft Size
1450 rpm
1750 rpm
2900 rpm
3500 rpm
A30 A40 A50 A60
Mega
5
Technical Data
Always check the pepipheral speed and
the maximum discharge pressure.
Pm=ps+pr (Q=O)ps=Suction Pressure
pr=Differential Pressure
Pm=Maximum Pressure
Q=Actual pump flow rate
Q opt=Pump flow rate at best effeciency rate
(1)Shaft MaterialAS 2837-Gr.431
Impeller MaterialAS 1830-Gr.T260
(2)Shaft MaterialAS 2837-Gr.431
Impeller MaterialAS 1565-C90250
rpm
3100
3500
3400
3000
3500
2900
3100
2950
2450
2950
2600
2450
3300
2550
2050
1800
2530
2500
2150
1650
2950
2450
2900
2500
2900
Max. Dia.mm176209174209174219260260260172219172333320260219266185219320332404265332404218265332419218265328413332404265332417
Min Dia.mm148178138173135178212214220131180122278270220180220155179270281330216280329162218280330158220264329280329218280330
Widthmm5.661291612881221173199132319363213181327231740373025604839332317373025
No. of Vanesmm66666655566666666666666666666566666666
Eye Dia.mm5656706875755870809293124728798115115142142101115123145142140159162162162180192192192142140162162162
Front Seal Dia.mm70708580909070859011011013585110120135135160160120135150160160160180180180180200210210210160160180180180
Rear Seal Dia.mm959595959595808080115115115105105140155140155155155155180180155180180180155180180180180180155180155155180
Max. Suction
Max. Discharge
Max. Test
Min/Max. with
Packing
Min/Max. with
Mech. Seal
Min/Max.
Rate of Flow
Rotation
Corrosion
Allowance
Flanges
Bearings
Lubrication
Maximum (1)
Drive Rating (2)
Shaft Deflectionmm
Sleeve O Dmm
Chamber I Dmm
Packingmm
Depthmm
Net Weightkg3444384942476873727081891041088992106105108126132162132142178136157156193183192254280142178157156193
Pump Size
Units
M32-160
M32-200
Tech. Data
M40-160
M40-200
M50-160
M50-200
M32-250
M40-250
M50-250
M65-160
M65-200
M80-160
M40-315
M50-315
M65-250
M80-200
M80-250
M100-160
M100-200
M65-315
M80-315
M80-400
M100-250
M100-315
M100-400
M125-200
M125-250
M125-315
M125-400
M150-200
M150-250
M150-315
M150-400
MH100-315
MH100-400
MH125-250
MH125-315
MH125-400
A60A50HD
Maximum Speed3500
Bearing BracketA30A40A50
Moment of Inertia
0.0238
0.0786
0.0336
kgm
2
0.0640
0.0394
0.0750
0.1820
0.1880
0.1920
0.0521
0.0985
0.0641
0.4396
0.4800
0.2232
0.1568
0.2904
0.1040
0.1800
0.5120
0.5698
1.2788
0.3172
0.2918
0.4656
0.6100
1.3832
0.2230
0.4100
0.4100
0.7740
1.6912
WR2 with water
0.8680
1.8600
0.6100
1.3832
0.7740
1.6912
Impeller
Axial Thrust
Balancing Holes and Seal Rings
Balance
Pressure
1000 kPa (10 bar)
1600 kPa (16 bar)
2400 kPa (24 bar)
Temp.
-10 to 105
-30 to 160
0.1Q opt / 1.1Q opt0.15Q opt / 1.1Q opt0.3Q opt / 1.1Q opt
oC
oC
Clockwise seen from Driver End
3.3
AS/NZS 4331.2, ISO 7005-2
630663086310631230310
Grease (temp. -10 to 105
o
C) Oil (temp. -30 to 160
o
C)
0.0130.03810.0730.1160.097
0.007430.02490.0370.0584
Maximum 0.05
Stuffing Box
3545607060
5565
mm
kW/rpm
7390.5
859585
10 X 1012.5 X 12.5
0.074
Mega
6
ITEM DESCRIPTION QTY MATERIAL COMBINATION
G (03, 06) GB (04, 07)
102 Casing 1 Cast Iron AS 1830-T260 Cast Iron AS 1830-T260
163 Discharge Cover 1 Cast Iron AS 1830-T260 Cast Iron AS 1830-T260
165 Cooling Cover 1 Cast Iron Cast Iron
183 Bracket Support 1 Steel Steel
210 Shaft 1 St. St AS2837-410 St. St AS2837-410
321 Bearing 2 Steel Steel
330 Bearing Bracket 1 Cast Iron Cast Iron
360 Bearing Cover 2 Cast Iron Cast Iron
400.1 Gasket, Sft Slv 1 Kevlar-NBR Kevlar-NBR
400.2 Gasket, Casing 1 Kevlar-NBR Kevlar-NBR
400.3 Gasket, Brg Cover 2 Kevlar-NBR Kevlar-NBR
400.4 Gasket, Imp Washer 1 Kevlar-NBR Kevlar-NBR
400.5 Gasket, Seal Plate 1 Kevlar-NBR Kevlar-NBR
411.1 Gasket, plug (1) 1 Kevlar-NBR Kevlar-NBR
411.2 Gasket plug (1) 1 Kevlar-NBR Kevlar-NBR
411.3 Gasket plug (1) 1 Kevlar-NBR Kevlar-NBR
411.4 Gasket plug (1) 1 Kevlar-NBR Kevlar-NBR
412.2 O Ring, Imp. Bolt 1 NBR NBR
412.3 O Ring, Cooling Cover 1 NBR NBR
412.4 O Ring, Cooling Cover 1 NBR NBR
421 Lip Seal 2 NBR NBR
433 Mechanical Seal 1 Ceramic/Carbon (2) Ceramic/Carbon (2)
452 Gland, Split 1 Cast Iron Cast Iron
458 Lantern Ring 1 Cast Iron Cast Iron
461 Packing 1 set PTFE Packing PTFE Packing
471 Seal Plate 1 Cast Iron Cast Iron
502.1 Wear ring, Casing 1 Cast Iron Cast Iron (3)
502.2 Wear ring, Impeller 1 Cast Iron Bronze
507 Slinger 1 NBR NBR
524 Shaft Sleeve 1 St. St AS2837-316 St. St AS2837-316
525 Spring Sleeve 1 St. St St. St
554.1 Washer, Csg Setscrew (4) Steel Steel
554.2 Impeller Washer 1 St. St AS2837-316 St. St AS2837-316
554.3 Washer, Sup Foot 1 Steel Steel
565 Drive Screw 14 St. St St. St
901.2 Setscrew, Casing (4) Steel Steel
901.4 Setscrew, B/c & Hsg (5) Steel Steel
901.5 Setscrew, Brg Cvr 8 Steel Steel
901.6 Setscrew, Foot 1 Steel Steel
901.7 Setscrew, Impeller 1 St. St AS2837-316 St. St AS2837-316
902 Stud, Gland 2 Steel Steel
903.1 Plug, Cgs/Suct 1 Steel Steel
903.2 Plug, Csg/Disch 1 Steel Steel
903.3 Plug, Drain 1 Steel Steel
903.4 Plug, Stfg/Box 2 Steel Steel
920 Nut, Gland 2 Steel Steel
940.1 Key, Impeller 1 Steel Steel
940.2 Key, Coupling 1 Steel Steel
970 Nameplate 1 St. St St. St
NOTES:
1 Plug gaskets not fitted where taper
plugs are installed
2 Option - silicon carbide / silicon
carbide
3 Option - bronze
4 Quantity:
8 off sizes: M32-200, M40-200,
M50-200, M65-200, M80-200,
M100-160, M100-200
10 off sizes: M32-250, M40-250,
M50-250, M80-250, M100-250,
M125-250, M150-250
12 off sizes: M40-315, M50-315,
M65-315, M80-315, M100-315,
M125-315
16 off sizes: M80-400, M100-400,
M125-400, M150-400
5 Quantity:
6 off bearing bracket A30, A40/R
8 off bearing bracket A50, A60
NOTE:
BEARING COVERS ITEM
360 ROTATED 90
O
FOR
CLARITY
ITEM 902, 920, 901.1,
901.2, 901.3, 901.4, 554.1
& 452 ALSO ROTATED
FOR CLARITY
MECHANICAL SEAL OPTION
SINGLE ROW BOLTING
APPLICABLE TO SOME MODELS ONLY
Mega
7
Sealing Arrangements
Option
Code
Standard
S2
1
Packing Application
Clean, non aggressive liquids, temperature up to
105
o
C internal sealing
10E Flushing liquid inlet
10S Flushing liquid outlet (at 180
o
C)
S2
2
S4
Liquids which are toxic, aggressive and/or with bad
smell.
Also pumps with suction from a vacuum tank. Sealing
with a clean liquid from an external source. (max.
temp. + 105
o
C)
Seal liquid: 1 L/min, pressure = 100kPa (1 bar) above
suction pressure.
Liquids having particles in suspension, or when major
contamination from the external source is to be
avoided.
(Sealing t max. = 105
o
C)
Seal liquid: 1 L/min, pressure = 100kPa (1 bar) above
suction pressure
Water applications where the suction pressure
exceeds 300kPa (3 bar)
Any of the above mechanical seals with flushing liquid
from an external source.
Flushing liquid: 1 L/min ( + 100) kPa
ps = suction pressure
pr = differential pressure
Mega
8
ps+pr
2
Sealing Arrangements
Option
Code
Standard
Mechanical Seal Application
Mechanical seal with internal flush for clean non-
aggressive water.
Maximum suction pressure = see page 4
M1
S3
M3
S2
S1
Mechanical seal with hard faces Silicon Carbide/
Silicon Carbide/Nitrile for slightly aggressive water.
Maximum suction pressure = see page 4
Balanced mechanical seal Crane T2US with Carbon/
Ceramic/Nitrile for clean non-aggressive water and
high suction pressures.
Maximum suction pressure = see page 4
Any of the above mechanical seals with seal flush
arrangement in accordance with API plan 11.
Any of the above mechanical seals with seal flush
filtered by cyclone separator.
Miminum differential pressure = 70kPa
Mega
9
Dimensions
PUMP WT.
SIZE DN1 DN2 a f h1 h2 b1 b2 b g1 g2 i1 m1 m2 m3 n1 n2 n3 n4 s1 s2 v w d l x kg
M32-160 50 32 80 385 132 160 111 120 50 15 8 42 100 70 65 240 190 155 110 14 14 100 285 24 50 100 34
M32-200 50 32 80 385 160 180 125 135 50 15 8 43 100 70 65 240 190 155 110 14 14 100 285 24 50 100 44
M32-250 50 32 100 500 180 225 162 171 65 18 8 39 125 95 65 320 250 155 110 14 14 130 370 32 80 100 68
M40-160 65 40 80 385 132 160 114 128 50 15 8 42 100 70 65 240 190 155 110 14 14 100 285 24 50 100 38
M40-200 65 40 100 385 160 180 135 148 50 15 8 43 100 70 65 265 212 155 110 14 14 100 285 24 50 100 49
M40-250 65 40 100 500 180 225 163 174 65 18 8 39 125 95 65 320 250 155 110 14 14 130 370 32 80 100 73
M40-315 65 40 125 500 200 250 189 199 65 18 12 39 125 95 65 345 280 155 110 14 14 130 370 32 80 100 104
M50-160 80 50 100 385 160 180 124 144 50 15 8 43 100 70 65 265 212 155 110 14 14 100 285 24 50 100 42
M50-200 80 50 100 385 160 200 143 161 50 15 8 43 100 70 65 265 212 155 110 14 14 100 285 24 50 100 47
M50-250 80 50 125 500 180 225 165 181 65 18 8 39 125 95 65 320 250 155 110 14 14 130 370 32 80 100 72
M50-315 80 50 125 500 225 280 197 212 65 18 12 42 125 95 65 345 280 155 110 14 14 130 370 32 80 100 108
M65-160 100 65 100 500 160 200 127 155 65 18 8 39 125 95 65 280 212 155 110 14 14 130 370 32 80 100 70
M65-200 100 65 100 500 180 225 151 174 65 18 8 43 125 95 65 320 250 155 110 14 14 130 370 32 80 100 81
M65-250 100 65 125 500 200 250 177 197 80 19 12 40 160 120 65 360 280 155 110 18 14 130 370 32 80 100 89
M65-315 100 65 125 530 225 280 206 226 80 19 12 39 160 120 65 400 315 155 110 18 14 160 370 42 110 140 126
M80-160 125 80 125 500 180 225 134 170 65 18 8 39 125 95 65 320 250 155 110 14 14 130 370 32 80 140 89
M80-200 125 80 125 500 180 250 154 183 65 18 8 39 125 95 65 345 280 155 110 14 14 130 370 32 80 140 92
M80-250 125 80 125 500 225 280 181 206 80 19 12 42 160 120 65 400 315 155 110 18 14 130 370 32 80 140 106
M80-315 125 80 125 530 250 315 217 241 80 19 12 39 160 120 65 400 315 155 110 18 14 160 370 42 110 140 132
M80-400 125 80 125 530 280 355 255 278 80 19 12 39 160 120 65 435 355 155 110 18 14 130 370 42 110 140 162
M100-160 125 100 125 500 200 280 176 222 80 19 12 40 160 120 65 360 280 155 110 18 14 130 370 32 80 140 105
M100-200 125 100 125 500 200 280 168 207 80 18 12 40 160 120 65 360 280 155 110 18 14 130 370 32 80 140 108
M100-250 125 100 140 530 225 280 183 214 80 20 12 39 160 120 65 400 315 155 110 18 14 160 370 42 110 140 132
M100-315 125 100 140 530 250 315 223 252 80 18 12 39 160 120 65 400 315 155 110 18 14 160 370 42 110 140 142
M100-400 125 100 140 530 280 355 254 282 100 20 12 39 200 150 65 500 400 155 110 22 14 160 370 42 110 140 178
M125-200 150 125 140 530 250 315 181 235 80 20 12 39 160 120 65 400 315 155 110 18 14 160 370 42 110 140 136
M125-250 150 125 140 530 250 355 223 271 80 18 12 39 160 120 65 400 315 155 110 18 14 160 370 42 110 140 157
M125-315 150 125 140 530 280 355 231 271 100 20 12 39 200 150 65 500 400 155 110 22 14 160 370 42 110 140 156
M125-400 150 125 140 530 315 400 275 307 100 20 12 39 200 150 65 500 400 155 110 22 14 160 370 42 110 140 193
M150-200 200 150 160 530 280 400 230 305 100 20 12 39 200 150 65 550 450 155 110 22 14 160 370 42 110 180 183
M150-250 200 150 160 530 280 375 228 302 100 20 12 39 200 150 65 500 400 155 110 22 14 160 370 42 110 180 192
M150-315 200 150 160 670 315 400 253 301 100 20 15 38 200 150 68 550 450 210 140 22 20 170 500 48 110 180 254
M150-400 200 150 160 670 315 450 284 326 100 20 15 38 200 150 68 550 450 210 140 22 20 170 500 48 110 180 280
MH100-315 125 100 140 530 250 315 223 252 80 18 12 39 160 120 65 400 315 155 110 18 14 160 370 42 110 140 142
MH100-400 125 100 140 530 280 355 254 282 100 20 12 39 200 150 65 500 400 155 110 22 14 160 370 42 110 140 178
MH125-250 150 125 140 530 250 355 223 271 80 18 12 39 160 120 65 400 315 155 110 18 14 160 370 42 110 140 157
MH125-315 150 125 140 530 280 355 231 271 100 20 12 39 200 150 65 500 400 155 110 22 14 160 370 42 110 140 156
MH125-400 150 125 140 530 315 400 275 307 100 20 12 39 200 150 65 500 400 155 110 22 14 160 370 42 110 140 193
FLANGE PUMP FOOT SHAFT END
Mega
10
D b
d
1
f No.
d
2
K
32 140 18 78 2 4 18 100 M16
40 150 18 88 3 4 18 110 M16
50 165 20 102 3 4 18 125 M16
65 185 20 122 3 4 18 145 M16
80 200 22 138 3 8 18 160 M16
100 220 24 158 3 8 18 180 M16
125 250 26 188 3 8 18 210 M16
150 285 26 212 3 8 22 240 M20
200 340 30 268 3 12 22 295 M20
BRANCH
SIZE
BOLTING
FLANGE
RAISED
FACE
DRILLING*
FLANGE DIMENSIONS AND DRILLING ACCORDING TO AS/NZS 4331.2, ISO 7005 - 2 - 16 BAR
(DIN 2533 / PN16)
*HOLES - EQUALLY SPACED OFF CENTRE
OPTIONS: FLANGE DRILLING ACCORDING TO AS129 TABLE ‘E’, ANSI B16-1 125lB
COUPLING END
KEY DIMENSIONS ARE NOMINAL AND ARE EXPRESSED IN
MILLIMETRES
SHAFT DIAMETER TOL.L H W SEAT
MODULE d j6 DEPTH
-0.004
+0.009
-0.005
+0.011
-0.005
+0.011
-0.005
+0.011
37
A60 48 100 9 14 42.5
A50 42 100 128
8 20
A40 32 70 8 10 27
A30 24 40 7
Flange Dimensions
Shaft Dimensions
Mega
11
CODE DESCRIPTION CONN.A-30 A-40 A-50 A-60
1M1 Pressure Gauge BSP 3/8"3/8"1/2"1/2"
1M2 Pressure Gauge BSP 3/8"3/8"1/2"1/2"
3M Pressure Gauge BSP 3/8"3/8"1/2"1/2"
6D Drain - Casing BSP 3/8"3/8"1/2"1/2"
8D Drain - Gland Seal BSP 1/2"1/2"3/4"3/4"
7E Cooling Inlet BSP 1/2"1/2"1/2"1/2"
7S Cooling Outlet BSP 1/2"1/2"1/2"1/2"
10E External Sealing In BSP 1/2"1/2"1/2"1/2"
10S External Sealing Out BSP 1/2"1/2"1/2"1/2"
13E Oil Filling BSP 1/2"1/2"1/2"1/2"
13D Oil Drain BSP 1/4"1/4"1/4"1/4"
Pump
Shaft Unit
Part Designation
Casing
Back Cover
Support Foot
Shaft
Impeller
Bearing
Bearing Bracket
Bearing Cover
Gasket
Gasket
Gasket
Gasket
O-Ring
Seal Ring
Gland
Lantern Ring
Packing
Wear Ring
Wear Ring
Slinger
Shaft Protection Sleeve
Impeller Nut
Key
Key
P/NO.
102
163
183
210
230
321
330
360
400.1
400.2
400.3
400.4
412.1
421
452
458
461
502.1
502.2
507
524
922
940.1
940.2
32-160 4 1 2 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 13 1 1 1 1 1
32-200 6 2 3 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 13 1 1 1 1 1
40-160 8 1 2 1 6 1 1 1 1 1 1 1 1 1 1 1 1 2 13 1 1 1 1 1
40-200 9 2 3 1 7 1 1 1 1 1 1 1 1 1 1 1 1 3 13 1 1 1 1 1
50-160 11 1 3 1 9 1 1 1 1 1 1 1 1 1 1 1 1 4 13 1 1 1 1 1
50-200 12 2 3 1 10 1 1 1 1 1 1 1 1 1 1 1 1 4 13 1 1 1 1 1
32-250 15 3 4 2 12 2 2 2 2 2 2 2 2 2 2 2 2 1 3 2 2 2 2 2
40-250 16 3 4 2 13 2 2 2 2 2 2 2 2 2 2 2 2 2 3 2 2 2 2 2
50-250 17 3 4 2 14 2 2 2 2 2 2 2 2 2 2 2 2 4 3 2 2 2 2 2
65-160 18 4 5 2 15 2 2 2 2 2 2 2 2 2 2 2 2 5 15 2 2 2 2 2
65-200 19 5 4 2 16 2 2 2 2 2 2 2 2 2 2 2 2 5 15 2 2 2 2 2
80-160 20 4 4 2 17 2 2 2 2 2 2 2 2 2 2 2 2 7 15 2 2 2 2 2
40-315 21 8 6 2 18 2 2 2 2 2 2 2 2 2 2 2 2 2 14 2 2 2 2 2
50-315 22 8 7 2 19 2 2 2 2 2 2 2 2 2 2 2 2 5 14 2 2 2 2 2
65-250 23 7 6 2 20 2 2 2 2 2 2 2 2 2 2 2 2 6 16 2 2 2 2 2
80-200 24 6 4 2 21 2 2 2 2 2 2 2 2 2 2 2 2 7 18 2 2 2 2 2
80-250 25 7 7 2 22 2 2 2 2 2 2 2 2 2 2 2 2 7 16 2 2 2 2 2
100-160 26 6 6 2 23 2 2 2 2 2 2 2 2 2 2 2 2 8 18 2 2 2 2 2
100-200 27 6 6 2 24 2 2 2 2 2 2 2 2 2 2 2 2 8 18 2 2 2 2 2
65-315 28 11 10 3 25 3 3 3 3 3 3 3 3 3 3 3 3 6 17 3 3 3 3 3
80-315 29 11 8 3 26 3 3 3 3 3 3 3 3 3 3 3 3 7 17 3 3 3 3 3
80-400 30 12 9 3 27 3 3 3 3 3 3 3 3 3 3 3 3 9 10 3 3 3 3 3
100-250 31 10 10 3 28 3 3 3 3 3 3 3 3 3 3 3 3 8 10 3 3 3 3 3
100-315 32 11 8 3 29 3 3 3 3 3 3 3 3 3 3 3 3 8 17 3 3 3 3 3
100-400 33 12 9 3 30 3 3 3 3 3 3 3 3 3 3 3 3 8 10 3 3 3 3 3
125-200 34 9 8 3 31 3 3 3 3 3 3 3 3 3 3 3 3 10 10 3 3 3 3 3
125-250 35 10 8 3 32 3 3 3 3 3 3 3 3 3 3 3 3 10 10 3 3 3 3 3
125-315 36 11 9 3 33 3 3 3 3 3 3 3 3 3 3 3 3 10 17 3 3 3 3 3
125-400 37 12 11 3 34 3 3 3 3 3 3 3 3 3 3 3 3 10 10 3 3 3 3 3
150-200 38 9 9 3 35 3 3 3 3 3 3 3 3 3 3 3 3 11 10 3 3 3 3 3
150-250 39 10 9 3 36 3 3 3 3 3 3 3 3 3 3 3 3 12 10 3 3 3 3 3
150-315 40 13 12 4 37 4 4 4 4 4 4 4 4 4 4 4 4 12 10 4 4 4 4 4
150-400 41 14 12 4 38 4 4 4 4 4 4 4 4 4 4 4 4 12 10 4 4 4 4 4
A30
A40
A50
A60
Service Connections
Interchangeability of Components
Mega
WEBSITE: www.ksbajax.com.au 24 HOUR EMERGENCY SERVICE LINE: 1300 301 356
Due to our policy of constant research and development, product specification may change without notice. Publication 2013 08/05 1/2K AGP
Victorian Head Office
27 Indwe St,
Tottenham, 3012
Tel: +61 (03) 9314 0611
Fax: +61 (03) 9314 7435
ksbvicsales@ksbajax.com.au
New South Wales
Unit 1, 28 Skinner Ave,
Riverwood, 2210
Tel: +61 (02) 9584 2099
Fax: +61 (02) 9584 2111
ksbnswsales@ksbajax.com.au
Queensland
Carberry St,
Ebbw Vale, 4304
Tel: +61 (07) 3282 1766
Fax: +61 (07) 3816 0225
ksbqldsales@ksbajax.com.au
South Australia
Unit 4, 348 Richmond Rd,
Netley, 5037
Tel: +61 (08) 8234 0066
Fax: +61 (08) 8443 5411
ksbsasales@ksbajax.com.au
Western Australia
Unit 2, 86 Catalano Circuit,
Canning Vale, 6155
Tel: +61 (08) 9455 7900
Fax: +61 (08) 9455 7800
ksbwasales@ksbajax.com.au
New Zealand
Unit 2, 5 Civil Place,
Albany, Auckland
Tel: +64 (09) 476 4047
Fax: +64 (09) 476 4048
pumps@ksbajax.co.nz
KSB Ajax Pumps Pty Ltd
ABN: 29 006 414 642