NEAX 2400 IPX DSS CONSOLE SYSTEM MANUAL - intelliHOUSE

chickpeasulotrichousNetworking and Communications

Oct 27, 2013 (3 years and 9 months ago)

227 views

ND-71771(E)
ISSUE 1
DSS (Direct Station Selection) Console System Manual
MAY, 2002
NEC Corporation
To view the latest issue of this document go to NEC Knowledgebase @ http://www.kbase.cns.nec.com.au &search for NEC-7146
LIABILITY DISCLAIMER
NEC Corporation reserves the right to change the specifications,
functions, or features, at any time, without notice.
NEC Corporation has prepared this document for use by its employ-
ees and customers. The information contained herein is the property
of NEC Corporation and shall not be reproduced without prior written
approval from NEC Corporation.
All brand names and product names on this document are trade-
marks or registered trademarks of their respective companies.
Copyright 2002
NEC Corporation
ND-71771 (E) PRODUCT LIABILITY
PL- 1
Issue 1
PRODUCT LIABILITY
BEFORE THE USE OF THIS MANUAL
1.FOR SAFETY USE
Here explains the safety use for the customer, which prevents danger to the life and damage to the property ac-
cidentally. The following are symbols and their meanings. Please read the following carefully before using this
manual.
SYMBOLS
DESCRIPTION
DANGER
This symbol indicates danger. You might be involved in a situation that
could cause deadly and bodily injury if you take wrong action.
WARNING
This symbol indicates warning. You might be involved in a situation that
could cause bodily injury and serious system fault if you take wrong ac-
tion.
ATTENTION
This symbol indicates attention. The system might not acheive its perfor-
mance or lead to the system stall if you take wrong action.
This telephone system is designed for use in the country NEC provides and can not be used in any other country.
If system-down, malfunction, defects, and external factors (such as electricity failure) cause profit loss indirectly, NEC does
not take any responsibilities for the profit loss.
We pay careful attention to making this manual, however, when you find mistakes on this manual, notify to NEC.
Contact the supplier or the service technician if the system needs repairs and installation.
Please read all the manuals related to your system carefully.
PRODUCT LIABILITY ND-71771 (E)
PL- 2
Issue 1
PRODUCT LIABILITY
2.NOTICE WHEN USED
2.1 Consideration of PBX, Power-related Equipment and Peripheral Equipment
This item describes the consideration before using PBX, the power-related equipment, and the peripheral equip-
ment (such as console, MDF, DAU, telephone, PC, printer, etc).
Preserve the following:
DANGER
When the system gives off smoke or burning smell, it might cause a fire, an electric
shock, or a failure if the system keeps operating. Turn off the power and confirm the
smoke disappears, and then contact supplier.
If equipment (such as PBX, Main Power, cabinet, and peripheral equipment) fall down
and be broken, turn off the power, and then contact the supplier.
If the inside of PBX or Main Power is wet by liquid such as water, turn off the power.
It might cause a fire, an electric shock, or a failure if the system keeps operating.
Do not touch the internal parts of Main Power for the purpose of disassembly and re-
modeling. It might cause a fire, an electric shock, or a failure.
(NEC does not take any responsibilities if the system or the equipment is disassembled
or remodeled.)
Do not put any container (such as vase, cup, and cosmetics) on Main Power and periph-
eral equipment. It might cause a fire, an electric shock, or a failure.
PWR
ND-71771 (E) PRODUCT LIABILITY
PL- 3
Issue 1
PRODUCT LIABILITY
DANGER
Do not damage, remake, forcefully bend, forcefully extract, nor forcefully twist an elec-
tric code and a wiring to/from PBX, Main Power and peripheral equipment. It might
cause a fire, an electric shock, or a failure. If the wiring is damaged, ask the supplier to
fix it.
Insert the electric plug into the outlet properly. Confirm no dust is on the blade of plug;
it might cause a fire.
Do not use other than the power designated when installed.
Do not try to fix or move Main Power by yourselves without the supplier or service tech-
nician’s help. Please ask them when the repair or the movement is necessary.
Do not put any metal or combustible object into a vent of PBX, Main Power, and the
peripheral equipment. If the object is in those equipment, turn off the power and ask the
supplier. It might cause a fire, an electric shock, or a failure if the system keeps operat-
ing.
Be careful of using the display part which the peripheral equipment has. In the case of
liquid crystal, the liquid is leaked and causes harm to human body and systems.
Before connecting customer-provided equipment (such as the other company products)
with NEC products such as PBX and peripheral equipment, ask the supplier and make
sure your equipment is compatible with NEC product. If it is not confirmed, do not con-
nect them. It might cause a fire or an electric shock.
dust
PWR
PWR
?
PRODUCT LIABILITY ND-71756 (E)
PL- 4
Issue 1
PRODUCT LIABILITY
WARNING
Fix the equipment. Do not put any object on PBX and Main Power; it might be danger-
ous if the object should fall down.
When plugging off a plug, be sure to grip the plug and extract it. If you grip the code
and extract it, it might cause a fire and an electric shock.
If a fault is considered as the lightening cause, ask the supplier.
Other than fulfilling the appropriate humidity and temperature, it is necessary to consid-
er the maintenance operation and the all-time ventilation in non-loading operation dur-
ing day-off and night. For example, when the height above floor is 1 m (3.281 feet), the
temperature should be from 20 to 25 °C (68 to 77 °F ) and the humidity should be more
or less 50 %.
ND-71771 (E) PRODUCT LIABILITY
PL- 5
Issue 1
PRODUCT LIABILITY
WARNING
Be careful of using a battery as following:
Rechargeable lead battery is used as the emergency battery of PBX. Check the back-
up for an electricity failure.
Battery electrolyte is harmful to human body. If the battery electrolyte is put on the
cloth, clean it using enough amount of water.
Do not cause the battery short intentionally. Do not put it near fire or put it into fire.
Do not damage it, such as disassembly, falling, and impact.
The battery life varies depending on the surroundings. The battery life is approxi-
mately three years. If the battery is used outside with high temperature, the battery
life is shortened to approximately one year.
If not replacing terminal or dead battery, the PBX system will not work in case such as
power failure. Besides it might cause smoking or fire due to leaking battery electrolyte.
Perform the periodic diagnosis surely. Note that the battery is one of periodic replace-
ment parts whose cost are charged to the customer. We recommend you to make a con-
tract with supplier or service technician about the routine maintenance.
Do not touch the peripheral equipment by wet hand. Do not wet the peripheral equip-
ment.
Do not touch the ink head and the internal of the printer. When replacing the ink ribbon
or the paper, make sure it is cool enough.
Do not drop nor impact the peripheral equipment. It might cause a failure.
155 53 13 123
Connection:
Connection:
PWR:
PWR:
Rcv:
Rcv:
Snd:
Snd:
TCP UDP
ENT
ENT
1
2
3
4
5
6
7
8
9
0
#
*
155 53
13
123
P
ro
to
c
o
l
:
Protocol:
T
CP
TCP
Con
nec
tion
:
Connection:
PWR
:
PWR:
R
cv:
Rcv:
Snd:
TCP
UDP
E
N
T
ENT
1
2
3
4
5
6
7
8
9
0
#
*
PRODUCT LIABILITY ND-71771 (E)
PL- 6
Issue 1
PRODUCT LIABILITY
2.2 Notice Regarding Lightenning Strikes
ATTENTION
Do not use benzine, thinner, and alcohol for cleaning. When it is difficult to clean dust
and dirt, put weaken neutral detergent onto a cloth, and give the cloth a wiring. Clean
dust and dirt with the cloth, and rub them with a dry cloth.
Do not place equipment in the following:
Locations which receive direct sunlight
Locations where the moisture exceeds the allowed level
Locations which might be wet with water, oil, and chemicals
Locations which is particularly low in temperature (such as an ice compartment)
Locations which receive the electric wave or the magnetism from TV and (two-way)
radio
Locations which receive the illegal electric wave
Note that the life of PBX and Main Power is shorten if placed in the location affected
by much of hydrogen sulfide or salt, such as seaside area.
WARNING
It is necessary to take proper procedures to avoid damage to the PBX caused by local lightening strikes
and other electrical surges.
As for grounding conductors, there needs to be two-type grounding conductors; one is below 10


(Type 1) and the other is below 100

(Type 2). In particular, the Type 1 is used for the electronics
circuit installment, therefore, it must be used as isolated system to keep from electricity difference
caused by lightening strikes.
The Type 1 is used when connecting the FE of PBX, the PE of Main Power, MDF, etc.
Extract the ground terminal (grounding electrode of three terminals) from the earth board same with
that of the main equipment. The ground terminal attached with AC100V plug outlet is used for MAT,
printer, MODEM, and measurement machine for maintenance.
Thinner
ND-71771 (E) PRODUCT LIABILITY
PL- 7
Issue 1
PRODUCT LIABILITY
2.3 Periodic Repair Parts and Disposables
ATTENTION
Replace the periodic repair parts such as fan, battery, backup battery, HD, fuse, and display. If not
change the parts and past the periodic term, sudden traffic fault might lead to the whole system failure
and damaging. Replace the disposables such as ink ribbon, FD, recording paper, and headset.
We recommend you to make a contract for the maintenance service.
PRODUCT LIABILITY ND-71771 (E)
PL- 8
Issue 1
This page is for your notes.
ND-71771 (E)
ISSUE 1
MAY, 2002
NEAX2400 IPX
Internet Protocol eXchange
DSS (Direct Station Selection) Console
System Manual
TABLE OF CONTENTS
Page
ND-71771 (E) TABLE OF CONTENTS
Page i
Issue 1
CHAPTER 1 OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.PURPOSE OF THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2.HOW TO USE THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
3.FUNCTIONAL OUTLINE - “What is a DSS for?” and “How does a DSS help?” . . . . . . . . . . . . . . . . .2
3.1 DSS/BLF (Direct Station Selection/Busy Lamp Field) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3.2 Add-On Module (ADM) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
4.SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
5.SERVICE CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
5.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
5.2 DSS/BLF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5.3 Add-On Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
CHAPTER 2 INSTALLATION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.CONNECTING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.1 Connecting Diagram of DSS/BLF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.2 Connecting Diagram of Add-On Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.CABLE LEAD ACCOMMODATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CHAPTER 3 DATA PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
1.DSS/BLF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.ADD-ON MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.OFFICE DATA SETTING SHEETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
TABLE OF CONTENTS ND-71771 (E)
Page ii
Issue 1
This page is for your notes.
ND-71771 (E) CHAPTER 1
Page 1
Issue 1
CHAPTER 1 OVERVIEW
1.PURPOSE OF THIS MANUAL
This manual aims to provide technicians with necessary information associated with the Direct Station Selection
console (referred to in this manual as “DSS”), including “What is a DSS for?” “How does a DSS help?” “How
to install a DSS” and “How to program the corresponding office data”. This manual deals with these subjects
under the following headings:
CHAPTER 1 OVERVIEW: Covers “What is a DSS for?”, “How does a DSS help?” and specifications
of the DSS.
CHAPTER 2 INSTALLATION PROCEDURE: Explains “How to install a DSS” and the associated
considerations which should be taken during installation.
CHAPTER 3 OFFICE DATA ASSIGNMENT: Deals with “How to program the corresponding data”.
For easy understanding a sample office data assignment sheet is shown in this chapter.
For your data assignment, blank sheets for the related commands are attached at the end
of this chapter.
2.HOW TO USE THIS MANUAL
The contents of this manual mainly focus on the DSS console. For this reason, in order to complete installation
tasks, refer to the “Installation Manual” of the PBX to which the DSS console is connected. When the DSS con-
sole is accommodated in a Distributed Access Unit (DAU), the “Installation Manual” of the DAU also required.
Figure 1-1 Outer View of DSS
Note:
The word “Distributed Access Unit (DAU)” in this manual is replaceable with “Digital Remote
Unit (DRU)”.
CHAPTER 1 ND-71771 (E)
Page 2
Issue 1
3.FUNCTIONAL OUTLINE - “What is a DSS for?” and “How does a DSS help?”
In accordance with user’s requirements, the DSS can be used as a DSS/BLF
or an Add-On Module
depending
on the following two factors:
Level Number (even or odd) of the allocated LENs for the DSS console
Office Data Programming
3.1 DSS/BLF (Direct Station Selection/Busy Lamp Field) mode
In this mode, a DSS console is used with a D
term
which receives a Direct Inward Dialing (DID) and/or Di-
rect-In Termination (DIT) call. When the DSS console receives such a call, the D
term
user can transfer the
incoming call to a preassigned destination by pressing the appropriate key on the console, while the caller
is automatically placed on hold. This function is called as the “Direct Station Selection (DSS)”. In addition
to this, each key on the console has a Light Emitting Diode (LED) to indicate the Busy/Idle status of each
assigned station. Thus the DSS can also provide a D
term
user with a “Busy Lamp Field (BLF)” function.
Figure 1-2 Direct Station Selection (DSS) / Busy Lamp Field (BLF) mode
• 
DSS function:  D
term
 user can transfer a DID/DIT call to a preassigned
destination by pressing a DSS key on the console.  
• 
BLF function:   D
term
 user can monitor Busy/Idle status of preassigned
stations.  
DSS/BLF
ï When a station which has been assigned
  to this DSS/BLF is busy, the associated
  LED lights red. In this example, station
  "304" is busy
300 304
BUSY INDICATION(RED)
DSS
KEY
NEC
Feature
Recall
Conf
Redial
Speaker
Answer
Transfer
Hold
4
5
6
GHI JKL MNO
7
8
9
PQRS
TUV
WXYZ
0
#
OPER
Exit Help
MIC
1
2
3
ABC DEF
...............
...............
...............
...............
ND-71771 (E) CHAPTER 1
Page 3
Issue 1
3.2 Add-On Module (ADM) mode
In this mode, a DSS console is used for the purpose of expanding Line/Feature Access keys of a D
term
. A
maximum of 60 keys are available in addition to the existing Line/Feature Access keys on each D
term
.
Figure 1-3 Add-On Module (ADM) mode
Table 1-1 Relationship between the MODE designation and Mounting Level Numbers
MODE ALLOWABLE LEVEL NUMBERS
DSS mode Even Number LV0, LV2, LV4, LV6
ADM mode Odd Number LV1, LV3, LV5, LV7
Add  On Module
ï In this ADD mode, each key can be used
  as a desired Line/Feature access key as 
  shown below.
CALL
BACK
VOICE
CALL
I-USE INDICATION(GREEN)
BUSY INDICATION(RED)
DSS
KEY
NEC
Feature
Recall
Conf
Redial
Speaker
Answer
Transfer
Hold
4
5
6
GHI JKL MNO
7
8
9
PQRS
TUV
WXYZ
0
#
OPER
Exit Help
MIC
1
2
3
ABC DEF
...............
...............
...............
...............
CHAPTER 1 ND-71771 (E)
Page 4
Issue 1
4.SPECIFICATIONS
Specifications for the DSS are shown in Table 1-2.
Table 1-2 Specifications for DSS
Note:
Allowable cable distances are as follows depending on the cable type.
Table 1-3 Cable Distance Limitations
Figure 1-4 Cable Distance Definition
ITEM SPECIFICATIONS
Number of KEYs × 60
Number of Light Emitting Diodes (LEDs) × 60 (RED) × 60 (GREEN)
Power Source AC 100 Volt ± 10 % (0.1A)
Allowable Cable Length
Note
850 m (2800 feet) • AC adapter is required.
Interface Card of a PBX PA-16ELCJ, PA-16ELCJ-B, PA-DAIG-A, PA-DAIJ-A
Dimensions
WIDTH 177 mm
DEPTH 218.2 mm
HEIGHT (1) 74.2 mm • When tilt legs are folded.
HEIGHT (2) 101.8 mm • When tilt legs are raised.
Weight 0.69 kg
CABLE LOCATION
CABLE 0.4 mm/26 AWG 0.5 mm/24 AWG
UNIT METERS FEET METERS FEET
1 PBX-DSS 540 1800 850 2800
2 DAU-DSS – – 200 650
PBX
MDF
Champ 
Connector
25-Pair installation Cable
Rosette
DSS Console
REAR VIEW
Cable Distance between PBX and DSS
Station Wire
0.4mm(26AWG)/
0.5mm(24AWG)
ï As illustrated below, the allowable cable distance includes the 25-pair installation cable.
ND-71771 (E) CHAPTER 1
Page 5
Issue 1
5.SERVICE CONDITIONS
This section covers considerations for designing the system to which DSS consoles are connected. To maintain
normal operation of the DSS, be sure to follow the instructions explained in this section. For readability, service
conditions of the DSS are explained, dividing them into the following headings.
General:deals with general service conditions.
DSS/BLF:explains service conditions which are unique to a DSS/BLF.
Add-On Module:explains service conditions which are unique to an Add-On Module.
5.1 General
Considerations described here are applied to both a DSS/BLF and Add-On Module.
(1) A DSS/BLF and an Add-On Module can coexist on one circuit card. Figure 1-5 illustrates an example
of port allocation on an ELC circuit card.
Figure 1-5 Port Allocation on an ELC card (Example)
(2) DSS consoles, the associated D
term
s, and stations which are to be assigned to the DSS keys must be-
long to the same Module Group.
(3) Multiple D
term
s cannot use one DSS console.
(4) Available circuit cards for the DSS are as follows:
• PA-16ELCJ
• PA-16ELCJ-B
• PA-DAIG-A (DAI)
• PA-DAIJ-A (DAI)
(5) The above mentioned considerations are also applied when a Distributed Access Unit (DAU) is used
between the PBX and the DSS.
ADM
D
term
D
term
D
term
ADM
D
term
DSS/BLF
ELC
LV
7
6
5
4
3
2
1
0
AD
M
D
term
D
term
D
term
AD
M
D
term
DSS/BLF
No terminal can be wired to this port.
NEC
Feat
u
re
Feature
...
......
...
...
...
...
......
...
......
...
...
...
S
p
e
a
ke
r
Ans
w
e
r
Tr
ansfer
Hold
4
5
6
4
GHI
5
JKL
6
MNO
7
8
9
7
P
Q
RS
8
TUV
9
WX
YZ
0
#
#
0
OPER
Exit
He
l
p
MIC
Feature
1
1
2
3
2
ABC
3
DEF
...
...
...
...
...
Reca
l
l
Conf
Redial
NEC
F
eature
F
eatu
re
...
......
......
...
...
.........
...
...
...
...
...
S
peake
r
Answe
r
Tr
a
n
s
fe
r
Hold
4
5
6
4
GH
I
5
JKL
6
MNO
7
8
9
7
PQ
RS
8
TUV
9
WXYZ
0
#
#
0
O
P
ER
Exit
He
lp
M
I
C
Feature
1
1
2
3
2
A
BC
3
DEF
...
......
......
Recal
l
Conf
Redial
NEC
F
e
atur
e
F
e
atur
e
...
......
......
...
......
......
.........
......
Speaker
Answ
e
r
Tra
n
s
f
er
Hold
4
5
6
4
GHI
5
JKL
6
MNO
7
8
9
7
PQRS
8
TUV
9
WXYZ
0
#
#
0
OPER
Exit
Help
MI
C
Feature
1
1
2
3
2
A
B
C
3
DEF
...
...
.........
Reca
l
l
Conf
R
e
di
al
NEC
Featur
e
Feature
...
......
......
...
...
...
......
......
...
......
S
p
e
ake
r
Answer
Tr
ans
f
er
Hold
4
5
6
4
GHI
5
JKL
6
MNO
7
8
9
7
PQRS
8
TUV
9
WXY
Z
0
#
#
0
OPER
Exit
Help
MIC
Featu
r
e
1
1
2
3
2
ABC
3
D
E
F
...
...
......
...
Recall
Conf
Re
d
ial
CHAPTER 1 ND-71771 (E)
Page 6
Issue 1
5.2 DSS/BLF
(1) One DSS/BLF console requires consecutive 2 ports on an ELC/DAI card.
(2) When a DSS console is used as a DSS/BLF, be sure to assign and wire the DSS/BLF to a specific
LEN whose level (LV) is even number
(LV = 0, 2, 4, 6). Since a DSS/BLF requires consecutive 2
ports for programming the DSS keys, the subsequent port of the designated port, to which the DSS/
BLF is wired, must be reserved.
Table 1-4
Level Assignment Conditions (DSS/BLF)
Note:
“n” represents here 0, 1, 2, 3.
As an example, Figure 1-6 depicts a case where a DSS/BLF is connected to “port 0” on an ELC card. In
this instance, any terminal cannot be wired to “port 1”.
Figure 1-6 Port Designation for DSS/BLF mode (Example)
LEVEL NUMBER CONDITIONS
2n A DSS console can be connected.
2n+1 Must be reserved for the DSS console.
LV
7
6
5
4
3
2
1
0
2n+1
2n
ï Only even numbered level is applicable to the DSS/BLF mode.
ï When a DSS/BLF is assigned to "LV 0", the subsequent port, in this instance "LV 1", must be retained for programming DSS keys of  the DSS/BLF 
   console.
No terminal can be wired to this port when a DSS/BLF is assigned 
to "port 0".
DSS/BLF
ELC
ND-71771 (E) CHAPTER 1
Page 7
Issue 1
(3) Key Numbers (KYN: 1-40), which appear in the AKYD command, correspond to 60 DSS keys as
shown below. As an example, this figure depicts a case where a DSS/BLF is connected to “LV 0”.
Figure 1-7 DSS Key Allocation (DSS/BLF)
KYN of
AKYD
KYN of
DSS
ñ
30
29
28
27
26
25
 
8
7
6
5
4
3
2
1
KYN of
AKYD
KYN of
DSS
60
59
58
57
56
55
 
38
37
36
35
34
33
32
31
(LV0)
DSS/BLF
ï Among 40 KYNs, KYN 10-39 are used.ï Among 40 KYNs, KYN 10-39 are used.
(LV1)
DSS/BLF
ï The DSS console is physically connected to the even numbered LV.
1
7
13
19
25
 31
 37
 43
 49
  55
2
8
14
20
26
 32
 38
 44
 50
  56
3
9
15
 21
 27
  33
  39
  45
   51
   57
4
10
16
 22
 28
  34
  40
  46
   52
   58
5
 11
 17
  23
  29
  35
  41
  47
   53
   59
 6
 12
 18
  24
  30
   36
   42
   48
    54
    60
ï The remaining lower 30 DSS keys are assigned as the second
  port (odd numbered LV), in this example "LV 1".
40
39
38
37
36
35
34
 
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
40
39
38
37
36
35
34
 
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
ï The upper 30 DSS keys are assigned as the first port (even 
  numbered LV, in this example "LV 0".
CHAPTER 1 ND-71771 (E)
Page 8
Issue 1
(4) The following features cannot be used when a DSS/BLF console encounters a busy station.
• CALL BACK
• CALL WAITING
• EXECUTIVE RIGHT-OF-WAY
• STEP CALL
(5) A station user cannot activate the following features for an incoming call from a DSS/BLF console.
Note
• CALL FORWARDING-OUTSIDE (including ALL CALLS, BUSY LINE, DON’T ANSWER)
• MULTIPLE CALL FORWARDING (including ALL CALLS, BUSY LINE, DON’T ANSWER)
• STATION HUNTING
• Split Call Forwarding
Note:
UNIFORM CALL DISTRIBUTION can be activated for an incoming call from a DSS/BLF as usual when
this feature has been set to the terminal.
ND-71771 (E) CHAPTER 1
Page 9
Issue 1
5.3 Add-On Module
(1) A maximum of 48 line appearances and 12 feature keys may be programmed for an Add-On Module.
(2) One Add-On Module occupies only one port on an ELC/DAI card.
(3) When a DSS console is used as an Add-On Module, be sure to assign the DSS console to a specific
LEN whose level (LV) is odd number
(LV = 1, 3, 5, 7). In addition, the associated D
term
which is used
in combination with the Add-On Module must be assigned to the preceding even numbered LEN lev-
el (LV = 0, 2, 4, 6).
Table 1-5
Level Assignment Conditions (Add-On Module mode)
Note:
“n” represents here 0, 1, 2, 3.
As an example, Figure 1-8 depicts a case where an Add-On Module is connected to “port 1” on an ELC
card. In this instance, the associated D
term
must be assigned to “Port 0”.
Figure 1-8 Port Designation for Add-On Module (Example)
LEVEL NUMBER CONDITIONS
2n+1 Add-On Modules are connected.
2n
The associated D
term
s which use keys on the Add-On Modules as additional Line
Feature access keys are connected.
ELC
LV
7
6
5
4
3
2
1
0
2n+1
2n
ï Only odd numbered level is applicable to Add-On Modules.
ï When an Add-On Module is assigned to "LV 1", the preceding port, in this instance "LV 0", must be used for the associated D
term
.
D
term
Add-On Module
NEC
Feature
...
...
...
...
...
.........
......
............
...
Speaker
Answer
Transfer
Hold
4
5
6
4
GHI
5
JKL
6
MNO
7
8
9
7
PQRS
8
TUV
9
WXYZ
0
#
#
0
OPER
Exit
Help
MIC
Feature
1
1
2
3
2
ABC
3
DEF
...
...
...
...
...
Recall
Conf
Redial
CHAPTER 1 ND-71771 (E)
Page 10
Issue 1
(4) To designate the meaning of the upper 24 keys on an Add-On Module, FKYs 17 through 40 of a D
term
which works in combination with the DSS are used. The remaining 36 keys on the

Add-On Module
are assigned using FKYs 5 through 40 of the original port of the

Add-On Module.

The relationship
between KYN, which appears in the AKYD command, and 60 keys on an

Add-On Module

is illus-
trated below. In this figure, an

Add-On Module

is connected to “LV 1” as an example.
Figure 1-9 Line/Feature Access Key Allocation (Add-On Module)
1
7
13
19
25
 31
 37
 43
 49
  55
2
8
14
20
26
 32
 38
 44
 50
  56
3
9
15
 21
 27
  33
  39
  45
   51
   57
4
10
16
 22
 28
  34
  40
  46
   52
   58
5
 11
 17
  23
  29
  35
  41
  47
   53
   59
 6
 12
 18
  24
  30
   36
   42
   48
    54
    60
KYN of
AKYD
KYN of
DSS
24
23
22
21
20
19
 18
17
8
7
6
5
4
3
2
1
KYN of
AKYD
KYN of
DSS
(LV0)
ï These FKYs are used for allocating desired
  Line/Feature keys to the Add-On Module.
ï Among 40 FKYs, KYN 5-40 are used for allocating
  desired Line/Feature keys to the Add-On Module.
(LV1)
Add-On Module
ï The upper 24 Line/Feature access keys are assigned as the first port 
  (even numbered level), in this example "LV 0".
60
59
58
57
56
55
54
53
52
51
34
33
32
31
30
29
28
27
26
25
ï The remaining lower 36 Line/Feature access keys are assigned as the 
  second port (odd numbered level), in this example "LV 1".
ï These FKYs are used for
   the Line/Feature keys of
   this original Dterm.
ï The Add-On Module is physically connected to the odd numbered LV.
40
39
38
37
36
35
34
33
32
31
 
14
13
12
11
10
9
8
7
6
5
4
3
2
1
40
39
38
37
36
35
34
 
24
23
22
21
20
19
18
17
16
15
14
4
3
2
1
D
term
ND-71771 (E) CHAPTER 1
Page 11
Issue 1
(5) The following Line/Feature keys must be assigned for KYNs 1 through 24:
• MESSAGE REMINDER (FKY = 6)
• My Line and/or Prime Line of the master D
term
.
(6) To assign Speed Calling-One Touch (FKY = 49), use KYNs 25 through 36, since the necessary mem-
ory area is retained for these KYNs only.
CHAPTER 2 ND-71771 (E)
Page 12
Issue 1
CHAPTER 2 INSTALLATION PROCEDURE
This chapter deals with installation procedure for the DSS console under the following headings:
1.CONNECTING DIAGRAM.
2.CABLE LEAD ACCOMMODATION.
1.CONNECTING DIAGRAM
1.1 Connecting Diagram of DSS/BLF
When the DSS console is used as a DSS/BLF, connect the associated cables referring to Figure 2-1 “Con-
necting Diagram of DSS/BLF”.
Figure 2-1 Connecting Diagram of DSS/BLF
ï Connecting Diagram
ï Connection of Modular Rosette
PIM
ELC
LT Connector
MDF
Installation Cable
A0 A0
B0 B0
Modular Rosette
DSS/BLF
DSS/BLF
MDF
PIM
DAI
LT Connector
Installation Cable
TA TA
TB TB
RA RA
RB RB
Pout A
Pout B
Distributed
Access
Unit
(DAU)
Note 1
Note 2
Modular Rosette
A0 B0(Polarity can be reversed.)
Modular Rosette
Modular Plug
DSS Console
4-Core Modular Jack
(As viewed from inserting direction)
1 2 3 4
1 2
3 4
1  - Yellow
2  - Green
3  - Red
4  - Black
1  - Red
2  - Green
3  - Black
4  - Blue
Note 1:
For more detailed information on the DAU, see the “DAU System Manual”.
Note 2:
These leads are not used for this system.
ND-71771 (E) CHAPTER 2
Page 13
Issue 1
1.2 Connecting Diagram of Add-On Module
When the DSS console is used as an Add-On Module, connect the associated cables referring to Figure 2-
2 “Connecting Diagram of Add-On Module”.
Figure 2-2 Connecting Diagram of Add-On Module
ï Connecting Diagram
ï Connection of Modular Rosette
PIM
ELC
LT Connector
MDF
Installation Cable
A0 A0
B0 B0
Modular Rosette
D
term
MDF
PIM
DAI
LT Connector
Installation Cable
TA TA
TB TB
RA RA
RB RB
Pout A
Pout B
Distributed
Access
Unit
(DAU)
Note 1
Note 2
Modular Rosette
A0 B0(Polarity can be reversed.)
Modular Rosette
Modular Plug
DSS Console
4-Core Modular Jack
(As viewed from inserting direction)
1 2 3 4
Modular Rosette
Add-On Module
Modular Rosette
A1
B1
A1
B1
D
term
Add-On Module
1 2
3 4
1  - Red
2  - Green
3  - Black
4  - Blue
1  - Yellow
2  - Green
3  - Red
4  - Black
Note 1:
For more detailed information on the DAU, see the “DAU System Manual”.
Note 2:
These leads are not used for this system.
CHAPTER 2 ND-71771 (E)
Page 14
Issue 1
2.CABLE LEAD ACCOMMODATION
The associated leads appear as shown below. This figure, however, illustrates an example of cable lead accom-
modations. For more detailed information on each card, see the “Circuit Card Manual” and/or the DAU System
Manual”.
Figure 2-3 Cable Lead Accommodation (Example)
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
E
RB
POUTB
TB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
E
RA
POUTA
TA
(1) PA-16ELCJ/PA-16ELCJ-B (ELC) (2) PA-DAIG-A/PA-DAIJ-A
ND-71771 (E) CHAPTER 3
Page 15
Issue 1
CHAPTER 3 DATA PROGRAMMING
This chapter describes how to program office data associated with the DSS.
1.DSS/BLF
This section covers how to assign a DSS/BLF. For easy understanding, the associated data programming is ex-
plained using an example shown in Figure 3-1.
Figure 3-1 Data Programming-DSS/BLF (Example)
2n+1
2n
In this example a DSS/BLF and the associated D
term
 are assigned as follows.
DSS/BLF
D
term
000100
000107
200 ï 201 (Note)
400
LV
7
6
5
4
3
2
1
0
ELC
To D
term
 (STN 400)
No terminal can be wired to this port (STN 201) when a DSS/BLF is 
assigned to "port 0".
To DSS/BLF
D
term
 (STN 400)
DSS/BLF (STN 200)
Terminal Line Equipment Number (LEN) Station Number (STN)
NEC
Feature
...
...
...
......
...
......
......
......
.........
Speaker
Answer
Transfer
Hold
4
5
6
4
GHI
5
JKL
6
MNO
7
8
9
7
PQRS
8
TUV
9
WXYZ
0
#
#
0
OPER
Exit
Help
MIC
Feature
1
1
2
3
2
ABC
3
DEF
.........
...
...
Recall
Conf
Redial
Note:
Two station numbers are required only for programming DSS keys. Accordingly, these numbers are
not used when operating the DSS/BLF.
CHAPTER 3 ND-71771 (E)
Page 16
Issue 1
DATA PROGRAMMING PROCEDURE (DSS/BLF)
When assigning DSS/BLF data, perform the following procedure. Note that “X” indicates the value should be
tailored to the existing system.
STEP 1:ASDT
Assign the DSS/BLF to an even numbered LEN level. (In this example, “LV 0” is used.)
TN:
STN:
LEN:
TEC:
RSC:
SFC:
Assign a station which is used for programming DSS keys (KYNs 31-60) to the subsequent LENs.
(In this example, “LV 1” is used.)
TN:
STN:
LEN:
TEC:
RSC:
SFC:
STEP 2:AKYD
Assign key data for 60 DSS keys. The upper 30 DSS keys (KYNs 1-30) are assigned using the first
port (“LV 0” in this example) and the remaining lower 30 DSS keys (KYNs 31-60) are assigned using
the second port (“LV 1” in this example).
Be sure to assign the associated D
term
station number as the “Station Number of Prime Line”.
TN:
STN:
TP:
PRI:
PL TN:
PL STN:
S:
MWD:
LN PRE:
KYN 1 must be programmed as the DSS/BLF station which has been assigned by the ASDT command.
KYN:
KYI:
KD:
TN:
STN:
RG:
KYN 2 must be programmed as the associated D
term
station.
KYN:
KYI:
KD:
TN:
STN:
RG:
even numbered LEN level
fixed
X
2 0 0
0 0 0 1 0 0
1 2
X
X
the subsequent LEN
fixed
X
2 0 1
0 0 0 1 0 1
1 2
X
X
Buttons 1-40 assignable
Enter the associated D
term
as a PL STN.
X
2 0 0 or 2 0 1
1
0
X
4 0 0
0 (= Off Hook Suppression is off)
0
0 (= Prime Line Pickup)
DSS/BLF station number
1
2 (= Multi Line)
0 (= Line)
X
2 0 0 or 2 0 1
X
associated D
term
2
2 (= Multi Line)
0 (= Line)
X
4 0 0
X
ND-71771 (E) CHAPTER 3
Page 17
Issue 1
Assign desired station numbers to the corresponding DSS keys on the console. In this instance, KYNs
10-39 are used. The upper and lower 30 keys are associated with even numbered port and odd num-
bered port respectively as shown below.
KYN:
KYI:
KD:
TN:
STN:
Figure 3-2 DSS key Assignment for DSS/BLF
desired station number (maximum 5 digits)
1 0 - 3 9
2 (= Multi Line)
2 (= For DSS Console Key)
X
X X X X X
ï Use KYNs 10 - 39 of an even numbered LEN level (0, 2, 4, 6) for programming the
upper 30 DSS keys on the DSS/BLF.
U: Upper L: Lower
ï Use KYNs 10 - 39 of an odd numbered LEN level (1, 3, 5, 7) for programming the
remaining lower 30 DSS keys on the DSS/BLF.
1
7
13
19
25
31
37
43
49
55
2
8
14
20
26
32
38
44
50
56
3
9
15
21
27
33
39
45
51
57
4
10
16
22
28
34
40
46
52
58
5
11
17
23
29
35
41
47
53
59
6
12
18
24
30
36
42
48
54
60
CHAPTER 3 ND-71771 (E)
Page 18
Issue 1
EXAMPLE OF DATA PROGRAMMING for DSS/BLF
TENANT
NUMBER
(TN)
1-63
STATION
NUMBER (STN)
MAXIMUM
5 DIGITS
LINE EQUIPMENT NUMBER
(LENS)
MG U G LV
0 0 0 1 0 0
TELE-
PHONE
EQUIPT.
CLASS
(TEC) 1-31
ROUTE
RESTRIC-
TION
CLASS
(RSC) 0-15
SERVICE
FEATURE
CLASS
(SFC)
0-15
REMARKS
×
2 0 0 ×
×
×
0 0 0 1 0 1
2 0 1 ×
×
×
0 0 0 1 0 7
4 0 0 ×
×
×
for DSS/BLF
for DSS/BLF
for the associated D
term
MY LINE
TENANT
NUMBER
(TN)
×
KEY
NUM-
BER
(KYN)
SERVICE
CONDITION
(KYI)
0-2
FEATURE
KEY CODE
(FKY)
1-320
KIND OF
LINE
(KD)
0-2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
30
31
32
33
34
35
36
37
38
39
40
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)



















0 (=Line)
0 (=Line)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
TENANT
NUMBER
(TN)
STATION
NUMBER
(STN)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
200
400 (=D
term
)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
RING
INFORMATION
FOR
EACH LINE
(RG)
0-7
×
×

















KIND OF
INCOM
(ICM)
0-2



















GROUP
ID
NUMBER
(G-ID)
1-50



















MULTI LINE INTERCOM
PRIORITY
OF
ANSWERING
CALL
(PRI)
0-4
0
TENANT
NUMBER
(PL TN)
×
STATION
NUMBER
(PL STN)
400(=D
term
)
ALLOW
OG
FROM
PRIME
LINE
(S)
0/1
0
MESSAGE
WAITING
DATA
DISPLAY
SELECTION
(MWD)
0/1
×
LINE
PREFERENCE
(LN PRE)
0/1
0
LINE
PREFERENCE
FOR SPEAKER
BUTTON
(SPK)
0-3
0
LINE
PREFERENCE
FOR
OUTGOING
BUTTON
(ORG)
0/1

TYPE OF
D
term
(TP)
0-3
1
LINE
PREFERENCE
FOR ANSWER
BUTTON
(ANS)
0-2

PRIME LINE
STATION NUMBER
(STN)
200
Even numbered
LEN Level
Assignment of
DSS keys (KYNs
1-30) using even
numbered LEN Level
Odd numbered
LEN Level
ASDT
AKYD
(For even numbered LV (2n))
ND-71771 (E) CHAPTER 3
Page 19
Issue 1
MY LINE
TENANT
NUMBER
(TN)
×
KEY
NUM-
BER
(KYN)
SERVICE
CONDITION
(KYI)
0-2
FEATURE
KEY CODE
(FKY)
1-320
KIND OF
LINE
(KD)
0-2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
30
31
32
33
34
35
36
37
38
39
40
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)
2 (=Multi Line)



















0 (=Line)
0 (=Line)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
2 (=DSS)
TENANT
NUMBER
(TN)
STATION
NUMBER
(STN)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
201
400 (=D
term
)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
RING
INFORMATION
FOR
EACH LINE
(RG)
0-7
×
×

















KIND OF
INCOM
(ICM)
0-2



















GROUP
ID
NUMBER
(G-ID)
1-50



















MULTI LINE INTERCOM
PRIORITY
OF
ANSWERING
CALL
(PRI)
0-4
0
TENANT
NUMBER
(PL TN)
×
STATION
NUMBER
(PL STN)
400(=D
term
)
ALLOW
OG
FROM
PRIME
LINE
(S)
0/1
0
MESSAGE
WAITING
DATA
DISPLAY
SELECTION
(MWD)
0/1
×
LINE
PREFERENCE
(LN PRE)
0/1
0
LINE
PREFERENCE
FOR SPEAKER
BUTTON
(SPK)
0-3
0
LINE
PREFERENCE
FOR
OUTGOING
BUTTON
(ORG)
0/1

TYPE OF
D
term
(TP)
0-3
1
LINE
PREFERENCE
FOR ANSWER
BUTTON
(ANS)
0-2

PRIME LINE
STATION NUMBER
(STN)
201
(For odd numbered LV(2n+1))
Assignment of
DSS keys (KYNs
31-60) using odd
numbered LEN Level
CHAPTER 3 ND-71771 (E)
Page 20
Issue 1
2.ADD-ON MODULE
This section covers how to assign an Add-On Module. For easy understanding, the associated data programming
is explained using an example shown in Figure 3-3.
Figure 3-3 Data Programming - Add-On Module (Example)
2n+1
2n
In this example, an Add-On Module and the associated D
term
are to be assigned as follows.
Add-On Module
D
term
000101
000100
201
200
LV
7
6
5
4
3
2
1
0
ELC
D
term
(STN 200)
Add-On Module
(STN 201)
Note
Terminal Line Equipment Number (LEN) Station Number (STN)
NEC
Feature
......
...
......
...
............
...............
Speaker
Answer
Transfer
Hold
4
5
6
4
GHI
5
JKL
6
MNO
7
8
9
7
PQRS
8
TUV
9
WXYZ
0
#
#
0
OPER
Exit
Help
MIC
Feature
1
1
2
3
2
ABC
3
DEF
...............
Recall
Conf
Redial
Note:
Station number “201” is used only for assigning Line/Feature access keys to the Add-On Module.
Accordingly, these numbers are not used when operating the Add-On Module.
ND-71771 (E) CHAPTER 3
Page 21
Issue 1
DATA PROGRAMMING PROCEDURE (Add-On Module)
When assigning Add-On Module data, perform the following procedure. Note that “X” indicates the value
should be tailored to the existing system.
STEP 1:ASDT
Assign a D
term
to an even numbered LEN level. (In this example, “LV 0” is used.)
Assign the Add-On Module to the subsequent odd numbered LEN level. (In this example, “LV 1” is
used.)
TN:
STN:
LEN:
TEC:
RSC:
SFC:
STEP 2:AKYD
Assign Line/Feature access keys to the Add-On Module. The upper 24 Line/Feature access keys belong
to the associated D
term
and the remaining lower 36 Line/Feature access keys belong to the Add-on
Module.
Assignment of the upper 24 keys:For assigning these key information, the associated D
term
port is
used.
TN:
STN:
TP:
PRI:
PL TN:
PL STN:
S:
MWD:
LN PRE:
KYN:
KYI:
KD:
TN:
STN:
RG:
ICM:
G-ID:
Assignment of the lower 36 keys:For assigning these key information, the Add-On Module port is
used.
TN:
STN:
TP:
PRI:
PL TN:
PL STN:
S:
MWD:
LN PRE:
odd numbered LEN level
fixed
X
2 0 1
0 0 0 1 0 1
1 2
X
X
Correspond to KYNs (1-24) on the Add-On Module
Buttons 1-40 assignable
X
2 0 0
1
0
X
2 0 0
0 (= Off Hook Suppression is off)
X
0 (= Prime Line Pickup)
1 - 1 6 (for D
term
)
1 7 - 4 0
X
X
X
X X X X
X
X
X
Buttons 1-40 assignable
Enter the associated D
term
as a PL STN.
X
2 0 1
1
0
X
2 0 0
0 (= Off Hook Suppression is off)
X
0 (= Prime Line Pickup)
CHAPTER 3 ND-71771 (E)
Page 22
Issue 1
KYN:
KYI:
KD:
TN:
STN:
RG:
ICM:
G-ID:
Figure 3-4 DSS Key Assignment for Add-On Module
Correspond to KYNs 25-60 on the Add-On Module.
5 - 4 0
X
X
X
X X X X
X
X
X
ï Use KYNs 17 - 40 of the associated D
term
for programming the upper 24 Line/Feature
access keys on the Add-On Module.
ï Use KYNs 5 - 40 of the Add-On Module for programming the remaining lower 36 Line/
Feature access keys on the Add-On Module.
1
7
13
19
25
31
37
43
49
55
2
8
14
20
26
32
38
44
50
56
3
9
15
21
27
33
39
45
51
57
4
10
16
22
28
34
40
46
52
58
5
11
17
23
29
35
41
47
53
59
6
12
18
24
30
36
42
48
54
60
ND-71771 (E) CHAPTER 3
Page 23
Issue 1
EXAMPLE OF DATA PROGRAMMING for Add-On Module
TENANT
NUMBER
(TN)
1-63
STATION
NUMBER (STN)
MAXIMUM
5 DIGITS
LINE EQUIPMENT NUMBER
(LENS)
MG U G LV
0 0 0 1 0 0
TELE-
PHONE
EQUIPT.
CLASS
(TEC) 1-31
ROUTE
RESTRIC-
TION
CLASS
(RSC) 0-15
SERVICE
FEATURE
CLASS
(SFC)
0-15
REMARKS
×
2 0 0 ×
×
×
0 0 0 1 0 1
2 0 1 ×
×
×
for D
term
for Add-On Module
MY LINE
TENANT
NUMBER
(TN)
×
KEY
NUM-
BER
(KYN)
SERVICE
CONDITION
(KYI)
0-2
FEATURE
KEY CODE
(FKY)
1-320
KIND OF
LINE
(KD)
0-2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
37
38
39
40
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
TENANT
NUMBER
(TN)
STATION
NUMBER
(STN)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
RING
INFORMATION
FOR
EACH LINE
(RG)
0-7
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
KIND OF
INCOM
(ICM)
0-2
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
GROUP
ID
NUMBER
(G-ID)
1-50
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
MULTI LINE INTERCOM
PRIORITY
OF
ANSWERING
CALL
(PRI)
0-4
0
TENANT
NUMBER
(PL TN)
×
STATION
NUMBER
(PL STN)
200(=D
term
)
ALLOW
OG
FROM
PRIME
LINE
(S)
0/1
0
MESSAGE
WAITING
DATA
DISPLAY
SELECTION
(MWD)
0/1
×
LINE
PREFERENCE
(LN PRE)
0/1
0
LINE
PREFERENCE
FOR SPEAKER
BUTTON
(SPK)
0-3
0
LINE
PREFERENCE
FOR
OUTGOING
BUTTON
(ORG)
0/1

TYPE OF
D
term
(TP)
0-3
1
LINE
PREFERENCE
FOR ANSWER
BUTTON
(ANS)
0-2

PRIME LINE
STATION NUMBER
(STN)
200 (=D
term
)
Even numbered
LEN Level
Assignment of Line/
Feature access keys
(KYNs 1-24) on
Add-On Module "201"
Assignment of Line/
Feature access keys
(KYNs 1-16) on
D
term
"200"
Odd numbered
LEN Level
ASDT
AKYD
(For Line/Feature access keys: KYNs 1-24 (
D
term
))
CHAPTER 3 ND-71771 (E)
Page 24
Issue 1
MY LINE
TENANT
NUMBER
(TN)
×
KEY
NUM-
BER
(KYN)
SERVICE
CONDITION
(KYI)
0-2
FEATURE
KEY CODE
(FKY)
1-320
KIND OF
LINE
(KD)
0-2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
37
38
39
40
2 (=Multi Line)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×

×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
0 (=Line)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
TENANT
NUMBER
(TN)
STATION
NUMBER
(STN)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
201

×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
RING
INFORMATION
FOR
EACH LINE
(RG)
0-7
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
KIND OF
INCOM
(ICM)
0-2

×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
GROUP
ID
NUMBER
(G-ID)
1-50

×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
MULTI LINE INTERCOM
PRIORITY
OF
ANSWERING
CALL
(PRI)
0-4
0
TENANT
NUMBER
(PL TN)
×
STATION
NUMBER
(PL STN)
200(=D
term
)
ALLOW
OG
FROM
PRIME
LINE
(S)
0/1
0
MESSAGE
WAITING
DATA
DISPLAY
SELECTION
(MWD)
0/1
×
LINE
PREFERENCE
(LN PRE)
0/1
0
LINE
PREFERENCE
FOR SPEAKER
BUTTON
(SPK)
0-3
0
LINE
PREFERENCE
FOR
OUTGOING
BUTTON
(ORG)
0/1

TYPE OF
D
term
(TP)
0-3
1
LINE
PREFERENCE
FOR ANSWER
BUTTON
(ANS)
0-2

PRIME LINE
STATION NUMBER
(STN)
201 (=Add-On Module)
Assignment of Line/
Feature access keys
(KYNs 25-60) on
Add-On Module "201"
Assignment of Line
Appearance data
for Add-On Module
"201"
(For Line/Feature access keys: KYNs 25-60 (Add-On Module))
(=Add-On
Module)
ND-71771 (E) CHAPTER 3
Page 25
Issue 1
3.OFFICE DATA SETTING SHEETS
In this section, blank sheets of the related commands are printed for your data assignment.
TENANT
NUMBER
(TN) 1-63
STATION
NUMBER
(STN)
5 DIGITS
LINE EQUIPMENT NUMBER
(LENS) TELEPHONE
EQUIPT.
CLASS (TEC)
1-31
ROUTE
RESTRIC-
TION
CLASS
(RSC)
0-15
SERVICE
FEATURE
CLASS
(SFC)
0-15
MAKE BUSY
INFORMA-
TION
(MB)
0/1
REMARKS
MG U G LV
ASDT
CHAPTER 3 ND-71771 (E)
Page 26
Issue 1
MY LINE
TENANT
NUMBER
(TN)
STATION NUMBER
(STN)
PRIORITY
OF
ANSWERING
CALL
(PRI)
0-4
PRIME LINE ALLOW
OG
FROM
PRIME
LINE
(S)
0/1
MESSAGE
WAITING
DATA
DISPLAY
SELECTION
(MWD)
0/1
LINE
PREFERENCE
(LN PRE)
0/1
LINE
PREFERENCE
FOR
SPEAKER
BUTTON
(SPK)
0-3
LINE
PREFERENCE
FOR ANSWER
BUTTON
(ANS)
0-2
LINE
PREFERENCE
FOR
OUTGOING
BUTTON
(ORG)
0/1
TYPE
OF
D
term
(TP)
0-3
TENANT
NUMBER
(PL TN)
STATION
NUMBER
(PL STN)
KEY
NUM-
BER
(KYN)
SERVICE
CONDITION
(KYI)
0 – 2
FEATURE
KEY CODE
(FKY)
1-320
KIND OF
LINE
(KD)
0-2
MULTI LINE INTERCOM
TENANT
NUMBER
(TN)
STATION
NUMBER
(STN)
RING
INFORMATION
FOR
EACH LINE
(RG) 0-7
KIND OF
INCOM
(ICM)
0-2
GROUP
ID
NUMBER
(G-ID)
1-50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
AKYD
ND-71771 (E) CHAPTER 3
Page 27
Issue 1
Note 1:
When KYI=None, it is not necessary to assign any data.
Note 2:
When KYI=FUNCTION, assign data for FKY only.
Note 3:
When KYI=Multi-Line, assign data for multiple telephone only.
KEY
NUM-
BER
(KYN)
SERVICE
CONDITION
(KYI)
0 – 2
FEATURE
KEY CODE
(FKY)
1-320
KIND OF
LINE
(KD)
0-2
MULTI LINE INTERCOM
TENANT
NUMBER
(TN)
STATION
NUMBER
(STN)
RING
INFORMATION
FOR
EACH LINE
(RG)
0-7
KIND OF
INCOM
(ICM)
0-2
GROUP
ID
NUM-
BER
(G-ID)
1-50
27
28
29
30
31
32
33
34
35
36
37
38
39
40
F1
F2
F3
F4
F5
F6
F7
F8
CHAPTER 3 ND-71771 (E)
Page 28
Issue 1
MY LINE
TENANT
NUMBER
(TN)
STATION NUMBER
(STN)
PRIORITY
OF
ANSWERING
CALL
(PRI)
0-4
PRIME LINE
ALLOW
OG
FROM
PRIME
LINE
(S)
0/1
MESSAGE
WAITING
DATA
DISPLAY
SELEC-
TION
(MWD)
0/1
LINE
PREFERENCE
(LN PRE)
0/1
LINE
PREFERENCE
FOR
SPEAKER
BUTTON
(SPK)
0-3
LINE
PREFERENCE
FOR
ANSWER
BUTTON
(ANS)
0-2
LINE
PREFERENCE
FOR
OUTGOING
BUTTON
(ORG)
0/1
TYPE
OF
D
term
(TP)
0-3
TENANT
NUMBER
(PL TN)
STATION
NUMBER
(PL STN)
KEY
NUM-
BER
(KYN)
SERVICE
CONDITION
(KYI)
0 – 2
FEATURE
KEY CODE
(FKY)
1-320
KIND OF
LINE
(KD)
0-2
MULTI LINE INTERCOM
TENANT
NUMBER
(TN)
STATION
NUMBER
(STN)
RING
INFORMATION
FOR
EACH LINE
(RG) 0-7
KIND OF
INCOM
(ICM)
0-2
GROUP
ID
NUMBER
(G-ID)
1-50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
ND-71771 (E) CHAPTER 3
Page 29
Issue 1
Note 1:
When KYI=None, it is not necessary to assign any data.
Note 2:
When KYI=FUNCTION, assign data for FKY only.
Note 3:
When KYI=Multi-Line, assign data for multiple telephone only.
KEY
NUM-
BER
(KYN)
SERVICE
CONDITION
(KYI)
0 – 2
FEATURE
KEY CODE
(FKY)
1-320
KIND OF
LINE
(KD)
0-2
MULTI LINE INTERCOM
TENANT
NUMBER
(TN)
STATION
NUMBER
(STN)
RING
INFORMA-
TION
FOR
EACH LINE
(RG)
0-7
KIND OF
INCOM
(ICM)
0-2
GROUP
ID
NUM-
BER
(G-ID)
1-50
27
28
29
30
31
32
33
34
35
36
37
38
39
40
F1
F2
F3
F4
F5
F6
F7
F8
ISSUE 1 ISSUE 2 ISSUE 3 ISSUE 4
DATE MAY, 2002 DATE DATE DATE
ISSUE 5 ISSUE 6 ISSUE 7 ISSUE 8
DATE DATE DATE DATE
NEAX2400 IPX Internet Protocol eXchange
DSS (Direct Station Selection) Console System Manual
Revision Sheet 1/1
ND-71771(E)
PAGE No.
ISSUE No.
1 2 3 4 5 6 7 8
PL-1
1
PL-2
1
PL-3
1
PL-4
1
PL-5
1
PL-6
1
PL-7
1
PL-8
1
i
1
Blank
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
1
10
1
11
1
12
1
13
1
14
1
15
1
16
1
17
1
18
1
19
1
20
1
21
1
22
1
23
1
24
1
25
1
26
1
27
1
28
1
29
1
PAGE No.
ISSUE No.
1 2 3 4 5 6 7 8