REQUEST FOR PROPOSAL UNIFIED SCHOOL DISTRICT NO. 383 2031 POYNTZ AVENUE MANHATTAN, KS 66502-5898

viraginityfumblingΛογισμικό & κατασκευή λογ/κού

2 Νοε 2013 (πριν από 3 χρόνια και 1 μήνα)

357 εμφανίσεις


1

REQUEST FOR PROPOSAL


UNIFIED SCHOOL DISTRICT NO. 383

2031 POYNTZ AVENUE

MANHATTAN, KS 66502
-
5898



DATE:
October
2
, 2013








RFP NO. P
1
314
-
V
-
1









NEW/USED SCHOOL

BUSES







Sealed proposals addressed to USD 383 Purchasing
Department will be received at
2031 Poyntz Avenue, Manhattan, KS 66502, until
1
:
00 P.M.
on October

24,

201
3

at
which time the proposals will be opened and read aloud. Proposal envelope shall be
plainly marked:




SEALED PROPOSAL FOR NEW/USED SCHOOL BUSES


RFP No. P1314
-
V
-
1

DO NOT OPEN BEFORE

OCTOBER

24
, 201
3

AT
1
:00 P.M.




Any proposal received later than the specified time, whether delivered in person
or mailed, shall be disqualified. The district reserves the right to reject any/or all
proposals and t
o accept the proposal deemed most advantageous to the
Manhattan
-
Ogden School District and to waive any formalities of bidding.


All bidders whose domicile is located outside the State of Kansas should furnish the
school district with a copy of their state’
s preferential bidding statutes and the applicable
percent received by in
-
state bidders from the state in which the contractor is located.





Tamara Dorst, Purchasing Accountant

Manhattan
-
Ogden School District #383





2


NOTICE TO BIDDERS


Items listed belo
w apply to and become a part of the terms and conditions of this
proposal unless superseded by any supplemental specifications or conditions enclosed
or attached hereto; in which case the attached or enclosed conditions will prevail.


1.

Inquires or protests
concerning this proposal must be directed to Tamara Dorst @
785
-
587
-
2000

or tamarado@usd383.org
.

All concerns, inquiries or protests to
specifications need to be addressed in writing before the proposal opening. This
may delay the proposal opening until
the matter can be resolved. Protests to the
award of the proposal need to be made by 5:00 P.M., the Friday following the Board
of Education’s award.


2.

Proposals should be submitted on the form(s) provided. Proposals must be received
in the Purchasing Depa
rtment before the hour and date specified. Late proposals
will be disqualified and returned unopened.

Please include detailed specifications
and information on all proposed items. Failure to include information may result in
the vendor’s proposal being
considered not meeting the specifications.


3.

Proposals cannot be altered or amended after opening time. Any alterations made
before opening time must be signed by the bidder or their agent. No
proposal

can
be withdrawn after opening time without the appro
val of the Purchasing Agent.


4.

It is not the policy of the Manhattan Unified School District No. 383 to purchase on
the basis of low
proposals

alone. In evaluating
proposals
submitted; price, service,
responsiveness to
proposal

instructions and conditions,

and bidder qualifications will
be taken into account. The district shall have the right to reject any or all
proposals
,
and in particular to reject a
proposal

not accompanied by any required Security or
data required by the
proposal

documents or a
propos
al

in any way incomplete or
irregular.


5.

Price quoted should be F.O.B. destination, inside delivery
,

unless otherwise stated
.
The
proposal

must clearly state the number of days required to deliver the product to
the specified location. Failure to state de
livery time obligates the bidder to make
delivery in thirty (30) days. Deliveries shall be made during normal school hours
unless prior approval has been obtained from the Purchasing Agent.


6.

The use of brand name is for the purpose of describing the stand
ard of quality,
performance and characteristics desired and is not intended to limit or restrict
competition.
Proposals

on items equal to or superior to the above are invited, but
bidders must submit complete specifications and descriptive materials in or
der to
have their
proposals

considered. Failure to submit adequate printed documentation
with the
proposal

may result in the determination of the bid being incomplete and
nonresponsive.



3

7.

Please state how long
proposal

prices will remain in effect after
proposal
has been
awarded, failure to do so will allow prices to remain in effect until final
proposal

award and contract has been carried out. All
proposals
are approved by the Board
of Education. Regular meetings of the Board of Education are held on t
he first and
third Wednesday of each month but may be subject to change. Please allow five (5)
business days for processing purchase orders, after the Board of Education has
made the award.


8.

When submitting a substitute article as equal, the full name and

illustrated
description must be given. The Board of Education reserves the right, however, to
decide upon its suitability for the intended use. Upon request, samples of substitute
articles must be submitted.


9.

Envelopes containing
proposals
must be seale
d and marked on the lower left
-
hand
corner with the firm name of the bidder and the bid
or proposal
number.


10.

A purchase order constitutes the buyer’s offer to the seller upon the terms and
conditions state herein, and shall become a binding contract on the

terms set forth
herein when it is accepted either by acknowledgement or performance.


11.

If the supplier refused or fails to make deliveries of the materials or supplies within
the time specified on the face of the request for the
proposal
of the purchase or
der,
the Board of Education may, by written notice, terminate the right of the supplier to
proceed with deliveries on such part or parts thereof as to which there has been
delay.


12.

Supplier shall certify and warrant that goods, personal property, channels a
nd
equipment sold and delivered are free and clear of any and all liens or claims of liens
for materials or services arising under and by virtue of the provisions of General
Statutes of Kansas, 1961 Supplement, Sections 5B
-
201, et. Seq., and any other lien
,
right or claim of any nature or kind whatsoever.


13.

All items must be properly packed or crated to insure delivery in good
c
ondition

and
in accordance with instructions listed on the face of the request for bid or purchase
order, if any.


14.

Rejected items wi
ll be held at the seller’s risk and expense. No replacement of
defective items shall be made by the seller unless agreed to by a Board of Education
representative in writing.


15.

Payment of the seller’s invoice is subject to adjustment for any shortage, or f
or
rejection of any item or items.


16.

All items contained in
proposal
are
proposed

as separate items unless otherwise
stated. In case of error in computations or totals, the unit price shall govern.



4

17.

Termination: Should the awarded contractor be sold, merg
ed or dissolved at any
time during the contracted period, the District shall retain the right to withdraw and
cancel any/all contract agreements without recourse from the original contracted
entity. In such case, the District may solicit bids
/proposals

fo
r services from eligible
firms.


18.

Pursuant to the Kansas Act Against Discrimination, K.S.A. 44
-
1001 et seq., the
following provisions are made a part of the terms and conditions of U.S.D. #383’s
contract
-
purchase orders, except where the contractor, vendor
or supplier employs
fewer than four (4) employees during the term of the contract
-
purchase order or
whose contracts with this school district cumulatively totals five thousand dollars
($5,000) or less during the fiscal year of the school district. Accepta
nce of such
contract
-
purchase orders by the contractor shall constitute agreement to these terms
and conditions. Contractor agrees that: (1) The contractor shall observe the
provisions of the Kansas Act Against Discrimination and shall not discriminate
a
gainst any person in the performance of work under the present contract
-
purchase
order because of race, religion, color, sex, physical handicap unrelated to such
person’s ability to engage in the particular work, national origin or ancestry;

(2) In all so
licitations or advertisements for employees the contractor shall include
the phrase, “equal opportunity employer”, or a similar phrase to be approved by the
Kansas Commission on Civil Rights; (3) If the contractor fails to comply with the
manner in which
the contractor reports to said commission in accordance with the
provisions of K.S.A. 1976 Supp. 44
-
1031, as amended, the contractor shall be
deemed to have breached the terms of this contract
-
purchase order, and it may be
canceled, terminated or suspended
, in whole or in part, by this purchaser; (4) If the
contractor is found guilty of a violation of the Kansas Act Against Discrimination
under a decision or order of the Kansas Commission on Civil Rights which has
become final, the contractor shall be deeme
d to have breached the terms of this
contract
-
purchase order, and it may be canceled, terminated or suspended, in whole
or in part, by this purchaser; (5) The contractor shall include the provisions of
paragraphs (1) through (4) inclusively of this paragra
ph in every subcontract or
purchase order so that such provisions will be binding upon such subcontractor or
vendor.



5

RFP SPECIFICATIONS

RFP NO. P
1
314
-
V
-
1


NEW/USED SCHOOL BUSES

DUE:
OCTOBER

2
4, 201
3

AT
1
:00 P.M.


The district is looking to purchase
two
to four

new or used Type “C” 71 passenger
buses
,
two

new Type “A” 21
-
30 passenger buses
, and one new Type “D” activity bus
.
Used buses may be up to
two

years old but can’t have more than
25,000

miles.
Proposals will be evaluated on condition, price, and
mileage. Final decision will be
made by the Board of Education. The Board may decide to split the award among
vendors or award to just one vendor.


SCHOOL BUS SPECIFICATIONS

TYPE "C" 71 PASSENGER BUS


(All Items listed should be considered as minimum sp
ecifications)




CHASSIS:

*


26,000 Lb. GVWR or equivalent


*

Tilt hood chassis


ALTERNATOR:

*

175 amp, 14 volt


AXLES:

*

Front: 10,000 Lb. .minimum capacity


*

17,500 Lb. Capacity rear axle and suspension with 5.04 rear
axle ratio (notify if ratio is dif
ferent)


BATTERY:

*

Two maintenance free batteries, 950 CCA minimum

mounted in a side compartment, 12 volt




negative ground


*

Enclosed battery compartment with sliding tray mounted in
left skirt


BRAKES:

*

Hydraulic brakes

*

four wheel disc

*

Parking br
ake


COOLING:

*

Heavy duty cooling system


*

Viscous Engine Fan


DRIVELINE GUARDS:

*

Around drive shaft in addition to standard


DRIVER SEAT:

*

6
-
way adjustable driver seat with cloth insert


*

3
-
Point attachment driver’s seat belt and shoulder harness
adj
ustable



6

ENGINE:

*

Cummins ISB 220 Horsepower Turbo
-
Charged diesel or
equivalent




(VT
-
365 engine
will not be considered
)


*

Heavy duty dry element air filter with restriction indicator


*

1000 Watt Block Heater


*

Electronic fast idle switch


EXHAUST:

*

Single horizontal exhaust system to meet EPA standards


FUEL TANK:

*

60
-
gallon fuel tank


GAUGES:

*

Full instrumentation including Voltmeter
-

Water temperature
-

Oil pressure
-

Fuel gauge




Speedometer


Odometer


Transmission temperature
gauge


HORNS:

*

Dual Electric horns


STEERING:

*

Integral type power steering


SUSPENSION:

*

Heavy duty front and rear shocks


TIRES:

*

11R22.5 G
-
Load rating.


*

11R22.5 G
-
Load rating.


TRANSMISSION:

*

Automatic transmission Allison 2000 series or equivalent


WHEELS:

*

22.5 x 7.5 10 hole hub piloted Budd wheels


WINDSHIELD:

*

Windshield to be tinted with shaded band at the top


WINDSHIELD WIPERS:

*


Heavy duty 2
-
speed intermittent electric windshield
wipers


*

Windshield washer


MISCELLANEOUS:

*


Single rectangula
r halogen headlights


*


Snap
-
on canvas grill cover


*


Front and rear tow hooks


BODY:

*

Interior headroom of 74" minimum



BODY PANELS:

*

Interior panels to be 18 gauge aluminum with Galvalume
from window line to seat rail


BUMPERS:


*

Front and rear Bum
per


7


*

Specialty Manufacturing Company Lectra Crossing Guard,
mounted on front of bus


COLOR:


*

Exterior
-

polyurethane national school bus chrome yellow



*

Roof


WHITE
(ONLY APPLIES TO NEW BUSES)



*

Interior
-

gray with flat black trim or standard



*

Guard rails, bumpers and borders around warning lights to
be black


DOOR EMERGENCY:


*
Glass in top and bottom with door header pad and warning
buzzer



*

Positive stop to hold door open when in use


DOOR ENTRANCE:


*

Electrically operated with heavy duty
door control and rod


*

Both leaves to open outward with 24" x 72" clear opening


*

Top and bottom to close against a rubber seal and no part of
door to ride inside stepwell


*

Header bumper over entrance door


*

Gas pocket door


ELECTRICAL:


*

Solenoid re
lay to de
-
activate body electrical system when
ignition is off



*

Wiring diagram with detailed electrical trouble shooting
owner maintenance manual


EMERGENCY

*

Three triangular flares and five Lb. fire extinguisher 2A10BC
with hose

EQUIPMENT

*

First aid
kit per national standards and body fluid clean
-
up kit



EMERGENCY EXIT:


*

Four emergency exit windows



*

T
wo Transpec safety vents with optional outside release
mechanism and optional alarm switch




wired to an indicator light, mounted on the center
-
li
ne of the
bus roof


FLOOR:


*

5/8" marine grade plywood sub
-
floor


FLOOR COVERING:


*

1/8" black smooth rubber under seats, over wheelhouse
and in driver's area



*

Step covered with black ribbed rubber with white nosing



*

Cover molding at side and rear

walls



*

Aluminum stripping on all seams


GRAB HANDLE:


*

Stainless steel grab handle at entrance door



8

HEATERS/DEFROSTERS:


*

Rear heater behind wheelwell, 80,000 BTU minimum


*

Left front heater and defroster 90,000 BTU minimum


*

Right front heater an
d defroster 50,000 BTU minimum


*

Heater water booster pump with separate switch


*

Heater water shut
-
off valves


*

Cover over heater hose from firewall to heater


*

Two 6” defroster fans, one mounted in center of windshield,
one mounted on left side of



windshield


HINGES:


*

Greaseable type hinges on front and rear door


INSULATION:

*

2" thick fire
-
resistant polyester in headliner, side and rear
walls


*

2” complete fiberglass insulation


*

Driver’s sound deadening package


LETTERING:


*

All state and
federal required lettering



*

All lettering must be vinyl (include:
MANHATTAN
-
OGDEN
USD 383

on both sides and
all lettering as required by Kansas State Law to include bus
# on 4 sides i
n 6” numbers.)


LIGHTS:

*

Front I.D. lights wired to ignition switch


*

Buzzer and red tel
-
tale light for emergency door


*

Two rows of dome lights


*

Single rear dome light on separate switch


*

Stepwell light door switch wired to clearance light switch


*

Side directional lights, mid
-
body mount


*

Weldon 7000 8
-
light warning flasher system, with cab
mounted light monitor


*

Amber turn
-
signal lenses with arrows on front and rear of
bus body


*

Strobe light mounted on top of bus behind roof hatch to turn
on

automatically with the ignition



switch


MIRRORS:

*

Heavy duty double nickel type side mirrors, heated


*

Bus Boy crossview mirrors on both front fenders heated


*

6” by 30” rear view mirror with sun visor


MUD FLAPS:

*

Rear mud flaps


RADIO:

*

AM/FM
radio with P/A system, automatic P/A over
-
ride,
front/rear fader control, 2 interior


9



speakers mounted at rear of bus, 2 interior speakers
mounted in middle of bus, 2 interior speakers



mounted at front of bus, steel covers over all speakers


RAILS GUARD
:

*

Three (3)
-

4 1/2" applied below window, at seat level and at
floor level


RAILS ROOF:

*

Two longitudinal exterior roof rails running full length of flat
part of roof


*

Drip molding
-

formed in roof panels over side windows


RAILS SHOULDER:

*

Padded s
houlder rails below side interior windows


RUST PROOFING:

*

Primer applied to both sides of all painted panels prior to
assembly


SEATS PASSENGER:

*

FMVSS fully padded with poly foam
-

two legged wall mount
with black frames


*

All seats shall be upholster
ed with fire barrier material,
Textech/Industries style 4771 Aramid/PB1



or equivalent


SECURITY SYSTEM:

*

Safety Vision SVR
-
4100 Mobile Digital Video
Recorder System to include: recording four video and
four audio channels in H.264 format

with recording from four
cameras;

ability to retrieve data wirelessly or manually and
monitor GPS positioning, speed tracking and recording, and
vital information for each recorded event. DVR must be
inside a lockable box and have cooling fans wired to r
un
when the DVR is powered on.



Include two (2) SV
-
830 DOME high resolution day/night
vision color cameras with 1/4
-
inch CCD 8.0 mm wide angle
lens, 420 TVL, and NTSC standard signal format built for
mobile applications


one on the front inside bus header
and
one on the rear inside bus header.



Include one (1)
SV
-
830 DOME high resolution day/night
vision color camera with 1/4
-
inch CCD 8.0 mm wide angle
lens, 420 TVL, and NTSC standard signal format built for
mobile applications to be placed above the driver
to record
the driver position and service door.



Include one (1) SV
-
830 DOME high resolution day/night
color camera with 1/4
-
inch CCD 8.0 mm wide angle lens,
420 TVL, and NTSC standard signal format built for mobile
applications to be placed facing out the
front windshield.



Included with Video System is one 32GB Compact Flash
Card.


10


STEPWELL:

*

Three step stepwell covered with black ribbed rubber with
white nosing


*

Cowl assist steps and handle, both sides


STOP ARM:

*

Specialty Manufacturing Company Lectra
stop Stop Arm with
#4110 electric base assembly;



Reflective surface of stop sign shall be high
-
intensity scotch
-
lite, and stop arm shall contain



high
-
intensity flashing LED lamps and wind guard


SUN VISOR:

*

As supplied by chassis manufacturer


SWIT
CH PANEL:

*

Switch panel to the left of driver in side panel compartment

*

Switch panel lights controlled by separate rheostat switch
located on switch panel


UNDERCOATING:

*

Floor, skirts and wheelhouses with Tectyle 121
-
B wax based
material or equivalent


*

Body undercoated complete, including fenders


VENTILATOR:

*

Static exhaust located in top front roof


WINDOWS:

*

Side windows
-

split aluminum sash with
TINTED

glass


*

Upper and lower emergency door glass


CHILD CHECK SYSTEM:

*

A post trip electroni
c child check system is required.
The system must be automatically activated any time the
bus is utilized for student transport.
(NO EXCEPTIONS )


MISCELLANEOUS:

*

Exterior entrance step light mounted on skirt panel at
entrance door


*

Backup alarm


*

Reflective marking package, to include School Bus front and
rear, rear outline and sides


*

Delivery will be guaranteed within 6 months of notification
unless otherwise stated



All specifications, whether listed or not, must meet or exceed all State and
F
ederal regulations now in effect.

Should the bidder take any exceptions to these specifications, they must be so
stated on a separate sheet and

accompany bid.


11


TYPE "A" 21
-
30 PASSENGER

A total of 2 NEW Type A buses


(All Items should be considered as min
imum specifications)


CHASSIS:

*

2014 or newer Commercial cutaway GM Van with 12,000
Lb. GVWR


ALTERNATOR:

*

130 amp, 12 volt


AXLES:

*

Front: 4,300 Lb.


rear 8,600 Lb. With 4.10/1 ration minimum


BATTERY:

*

Single 600 CCA battery, 12 Volt negative ground


BRAKES:

*

Power with 4 wheel anti
-
lock with brake warning light

*

Front


disc, 12.5” rotor


rear, drum 13” X 3.5” or disc

*

Parking brake
-

cable to rear wheels

*

Or Equivalent


COOLING:

*

Heavy duty radiator and transmission oil cooler


DRIVELINE GUAR
DS:

*

Around drive shaft in addition to standard


DRIVER DOOR:

*

Left side with armrest, roll down window and key lock


DRIVER SEAT:

*

6
-
way adjustable driver seat with cloth insert


ENGINE:

*

Minimum 6.0L Gasoline engine compatible with E
-
10
unleaded fuel

*

Paper element air cleaner, spin on oil filter and engine oil
cooler


EXHAUST:

*

Single with aluminized muffler


FUEL TANK:

*

35
-
gallon with hand fill and heat shield for exhaust


GAUGES:

*

Voltmeter
-

Water temperature
-

Oil pressure
-

Fuel level
-

Spee
dometer
-

Odometer



and trip Odometer


HORNS:

*

Electric high and low note


STEERING:

*

Power steering



12

SUSPENSION:

*

Heavy duty front and rear shock absorbers with front
stabilizer bar


*

Front springs 4,300 lb.
-

rear springs 8,600 lb.

*

Heavy duty chas
sis package and school bus equipment
package


TIRES:

*

LT225/75R 16D, tubeless radial with all season tread


TRANSMISSION:

*

Four
-
speed automatic with overdrive


WHEELBASE:

*

159" minimum with 12,000 lb. GVWR


WHEELS:

*

16" X 6" 8 stud disc
-

single front
and dual rears


WINDSHIELD:

*

Tinted solar
-
ray glass on windshield and driver’s door


WINDSHIELD WIPERS:

*

Intermittent two speed electric with washers


MISCELLANEOUS:

*


Single rectangular halogen headlights


BODY:

*

Type "A
-
1" school bus with s
eating for 24
-
30 passengers


*

Interior headroom of 73"
-

Exterior width of 96"
-

Interior
width of 90"


*

Must meet FMVSS 60% joint strength standards



BARRIER:

*

Two fully padded barriers located in front of the first row of
passenger seats


BODY PANELS
:

*

Interior panels to be 18 gauge aluminum with Galvalume
from window line to seat rail


*

Exterior panels to be 16 gauge smooth aluminum


BUMPERS:


*

Front: as supplied by chassis manufacturer


*

Rear: full width, wrap around 3/16" thick and 9 3/4" high
with
concave design


COLOR:


*

Exterior
-

polyurethane national school bus chrome yellow



*

Roof
-

WHITE



*

Interior
-

gray with flat black trim



*

Guard rails, bumpers and borders around warning lights to
be black


COMPARTMENTS:


*

Overhead panels in fr
ont and rear bulkhead for electrical
wiring access



13

DOOR EMERGENCY:


*
Glass in top and bottom with door header pad and warning
buzzer



*

Positive stop to hold door open when in use


DOOR ENTRANCE:


*

Electrically operated with heavy duty door control and

rod


*

Both leaves to open outward with 24" x 72" clear opening


*

Top and bottom to close against a rubber seal and no part of
door to ride inside stepwell


DRIVER'S DOOR
STEP:

* External step mounted below driver's side door


ELECTRICAL:


*

Solenoid rel
ay to de
-
activate body electrical system when
ignition is off



*

Wiring diagram with detailed electrical trouble shooting
owner maintenance manual


EMERGENCY EQUIPMENT
*

Three triangular flares and five Lb. fire extinguisher
2A10BC with hose


*

First aid k
it per national standards and body fluid clean
-
up kit



EMERGENCY EXIT:


*

Two emergency exit windows and one roof hatch with
buzzer and outside release




handle (Transpec)


FLOOR:


*

5/8" exterior grade plywood over 16 gauge corrugated
aluminum floor she
ets with high strength




steel cross members every 28"


FLOOR COVERING:


*

1/8" black smooth rubber under seats, over wheelhouse
and in driver's area



*

Step covered with black ribbed rubber with white nosing



*

Cove molding at side and rear walls


GRA
B HANDLE:


*

Stainless steel grab handle at entrance door


HEATERS/DEFROSTERS:

*

Front: deluxe
outside air heater and defroster system


*

Rear: minimum 50,000 BTU and two heater cut off valves in
engine compartment


*

One 6" auxiliary two speed fan mounted

on door control


HINGES:


*

Greaseable type hinges on front and rear door


INSULATION:

*

2" thick fire
-
resistant polyester in headlining, side and rear
walls


14


LETTERING:


*

All state and federal required lettering



*

All lettering must include:
MANHATTA
N
-
OGDEN USD 383

on both sides and all lettering as required by Kansas State law to include 6” bus # on 4
sides


LIGHTS:

*

Two 4" backup with clear lens


*

Three amber cluster with metal shields on front
-

three red
cluster on rear LED


*

Side marker lights

and reflectors as required


*

Two front chassis equipped directional lights and two 7" rear
LED amber directional lights


*

Two interior dome lights and driver dome light


*

Interior stepwell light operating with entrance door


*

Two 7" red combination LE
D stop and tail lights plus two 4"
combination LED stop and tail lights


*

Eight light warning system with master switch control and
Weldon 7,000 electronic flasher


*

Side directional lights


*

Strobe light mounted on top of bus behind roof hatch to turn
on automatically with the ignition



switch


LOCKS:

*

Key lock for drivers door and key lock for rear door with
starter interlock


MIRRORS:

*

One 6" x 16" interior
-

two 7" x 10" exterior rearview
-

two
quadrispherical crossview


All



heated


MUD
FLAPS:

*

Front and rear


RADIO:

*

AM/FM radio with two speakers in passenger area


RAILS GUARD:

*

Three (3)
-

4 1/2" applied below window, at seat level and at
floor level


RAILS ROOF:

*

Two longitudinal exterior roof rails running full length of flat
part

of roof


*

Drip molding
-

formed in roof panels over side windows


RAILS SHOULDER:

*

Padded shoulder rails below side interior windows


RUST PROOFING:

*

Primer applied to both sides of all painted panels prior to
assembly



15

SEATS PASSENGER:

*

Seating capac
ity for 24
-
30 children


*

Left side of bus standard FMVSS fully padded with poly
foam
-
two legged wall mount with black



frames


*

Right side of bus CE White Co Child Restraint Seats or IMMI
SafeGuard FlexSeat with two



integrated child seats per seat


*

The first four rows of seats are to be 39" on each side with
26" and 39" seat on the last row


*

All seats shall be upholstered with fire barrier material,
Textech/Industries style 4771 Aramid/PB1




or equivalent


STEPWELL:

*

Two step stepwell covered wi
th black ribbed rubber with
white nosing


STOP ARM:

*

Electrically operated with two 4" red strobe lights and wind
guard


SUN VISOR:

*

As supplied by chassis manufacturer


SWITCH PANEL:

*

Located in bulkhead above driver with (rocker type) labeled,
and ba
ck lit switches



with international symbols

*

Switch panel lights controlled by separate rheostat switch
located on switch panel


UNDERCOATING:

*

Floor, skirts and wheelhouses with Tectyle 121
-
B wax based
material or equivalent


VENTILATOR:

*

Static exhau
st located in top front roof


WINDOWS:

*

Driver's as supplied by chassis manufacturer


*

Side windows
-

split aluminum sash with
TINTED

glass


*

Upper and lower emergency door glass tinted


*

Right front vision glass (ahead of entrance door) to be one
piec
e with 340 sq. in. glass area


AIR CONDITIONING:

*

Dash air conditioning as supplied by the chassis
manufacturer.


*

Rear air
-

Compressor must be separate from Chassis
(dash) A/C


SECURITY SYSTEM:

*

Safety Vision SVR
-
4100 Mobile Digital Video
R
ecorder System to include: recording four video and
four audio channels in H.264 format with recording from four

16

cameras;

ability to retrieve data wirelessly or manually and
monitor GPS positioning, speed tracking and recording, and
vital information
for each recorded event. DVR must be
inside a lockable box and have cooling fans wired to run
when the DVR is powered on.



Include two (2) SV
-
830 DOME high resolution day/night
vision color cameras with 1/4
-
inch CCD 8.0 mm wide angle
lens, 420 TVL, and NTS
C standard signal format built for
mobile applications


one on the front inside bus header and
one on the rear inside bus header.



Include one (1)
SV
-
830 DOME high resolution day/night
vision color camera with 1/4
-
inch CCD 8.0 mm wide angle
lens, 420 TVL,
and NTSC standard signal format built for
mobile applications to be placed above the driver to record
the driver position and service door.



Include one (1) SV
-
830 DOME high resolution day/night
color camera with 1/4
-
inch CCD 8.0 mm wide angle lens,
420 TVL
, and NTSC standard signal format built for mobile
applications to be placed facing out the front windshield.



Included with Video System is one 32GB Compact Flash
Card.


MISCELLANEOUS:

*

Rear tow hooks


*

Exterior entrance step light mounted on skirt panel

at
entrance door


*

Backup alarm


*

Reflective marking package, to include School Bus front and
rear, rear outline and sides


*

Front bumper crossing guard, Specialty Mfg. 6
-
series solid
state


*

Delivery will be guaranteed within 6 months of notification

unless otherwise stated
















17

Specifications for a Rear Engine, “Type D” Multi Function School Activity Bus
Body/Chassis

1.

Vehicle shall be new, 2014 or newer model year transit (Type D)

2.

Chassis and body are to be designed, engineered, and built in
U.S.A. by
one manufacturer as one complete and integrated vehicle

3.

Vehicle capacity to be
46

passenger minimum

4.

Wheelbase will be
273

inches maximum

5.

Turning radius at curb not to exceed
33.2

6.

Minimum body length to be
40.6

feet








CHASSIS REQUIREMENTS


1.

AIR CLEANER
(Combustion)




Must be dry type with easily changeable element. An
appropriate restriction indicator monitoring air flow from the
cleaner to the engine intake is required.
Must contain a
moisture/particle ejector.


2.

AIR INTAKE

(Combustio
n)



The combustion air source for the engine must be located right
side, rear, above window center line.


3.

ALTERNATOR



Must be 320 Amp Leece Neville, high
-
output and provide at
least 50% of the rated charge at engine idle.






4.

AXLES / SUSPENSION





Front



Must be heavy duty I
-
beam construction with a minimum 13,200
lbs. capacity, Oil lubed wheel bearings.
Hubcaps with window
seal included. Must have minimum 40
-
degree wheel turn angle




Rear

Must be mini
mum 23,000 lbs. capacity single speed with 5.38 to
1 ratio.
Oil lubed bearings.



SHOCK ABSORBERS





Front and Rear

Heavy duty dual acting shocks (1 per side)


SPRINGS





Front



Hendrickson “Airtek” front air
-
suspension



Rear


18


Hendrickson “Comfort
-
Air”

rear air
-
suspension



5.

BATTERIES





Minimum 2100 CCA (combined). 2/0 gauge battery cables are



included.



7.

BRAKING SYSTEM

Service



Air drum brakes, 16.5x 6 front and 16.5x 8.62 rear
-

30/30 brake
chambers, ABS anti
-
lock. Bendix AD
-
SP spin
-
on ai
r dryer.
Meritor automatic slack adjusters. Dustshields front and rear.

Total capacity of wet tanks 5800 cu. in.



Air compressor: Bendix 13.2 CFM capacity @1250 rpm,
compressor gear driven. Uses filtered and turbo charged clean
engine air.



Emergen
cy/Parking



30 sq. in. spring brake system with treadle valve
modulation. Instrument panel mounted valve provided for
parking.


7.

BUMPERS






a.

Smooth

front bumper must be one
-
piece 1/4" thick steel
plate. Front bumper must include step holes for cle
aning
windshield.



b.

Rear bumper to be 12”
after forming

and have 14"
wraparound at corners with
double "A" frame bracing

for
greater rear impact resistance. Rear bumper must be one
piece 3/16" thick steel plate.



c.

Front and rear bumpers must be die
-
formed, 12" high,
after
forming
, with 90° flanges, top and bottom.


8.

CONTROLS





a.

Electronic fast idle



b.

Key type starter



c.

Column mounted headlight dimmer



d.

Hazard switch on steering wheel



e.

Self canceling turn signal with indicator light
s



f.

Rheostat dimmer for driver instrument illumination



g.

Dash mounted transmission shifter



h.

Backlit rocker switches for all accessories
must be mounted for easy access at driver’s left below
window.


19

i.

Engine Compartment
-

Remote engine start swi
tch, starter button,

compartment light switch.


9.

COOLING SYSTEM





a.

Charge air and cross
-
flow radiator in tandem located on left
side at rear of vehicle.



b.

A 26" dia. nylon cooling fan is hydraulically driven and
thermostatically modulated by se
nsors in both coolant jacket
and engine charge air intake.



c.

Black rubber coolant hose with constant torque clamps to
hold seals in place.



d.

Transmission fluid cooled by 2100 BTU/Min. heat exchanger
mounted external to radiator



e.

Coolant to prov
ide anti
-
freeze protection to
-
34°F.


10.

DRIVE LINE





Must be have a protective guard around shaft with lubed
for life components.


11.

ENGINE





Minimum 300 HP
;
900 lb
-
ft. torque
. Must be a Cummins 2010
EPA Engine and SCR (Selective Catalytic Reduc
tion) using
DEF (Diesel Exhaust Fluid) for Maximum Fuel Efficiency. Must
include a 1000W, minimum, internal engine block heater.
Engine should have unaided cold starts to 0
0
F.


12.

EXHAUST





3.5" O.D. 2
-
Ply stainless steel with catalytic converter,
bellow
flex style piping from engine turbo
-
charge to in line muffler.
Stainless steel muffler. 4" O.D. 16 gauge aluminized steel
tailpipe, exits through bumper, curb side. Wide band exhaust
clamps used at all joints.


13.

FLOOR, DRIVER AREA





Must b
e

raised 2",

minimum, above floor, with .62" plywood with
.19" ribbed rubber floor cover.


14.

FRAME





Main Frame
-

Dual "C" channels, 9.63" high with 3" flanges
made of .25 thick, 50,000 PSI steel, Section Modulus = 10.1 in.
cu.



Insert Dual "C" channe
ls, 9 1/6" web with 2 3/4" flanges made of
.25 thick, 50,000 PSI steel, Section Modulus = 9.5 in. cu.


20



Sub
-
Frame
-

Dual "C" channels, 50,000 psi steel, the sub
-
frame
rails are turned with flanges outward and lowered 6" below main
frame to best accommodate

engine and related components.



Sub
-
frame rails are 65" long and overlap main rail and insert 24"
where joining is reinforced with dual 3"x3', ,1/4" thick angle iron.



All permanent fixtures on frame are to be attached with hi
-
tensile strength "Huck
-
Sp
in" fasteners with swaged lock nuts.


NO EXCEPTIONS


Tapered rails are
not

acceptable


any deviation from this
specification will result in the rejection of your bid.


15.

FUEL SYSTEM





Must be
100
gallon capacity,
minimum
, aluminized steel, safety
ta
nk mounted between frame rails. Includes a sender
inspection plate and right hand fill opening with spring loaded,
locking

door.
Fuel pump must be mounted on engine.


16.

HORN





Electrical dual with non
-
glare horn button emblem.


17.

INSTRUMENTS






a.

Electronic speedometer/odometer with seven digits, with trip
odometer



b.

Fuel level gauge



c.

Voltmeter



d.

Ammeter



e.

Oil Pressure gauge



f.

Low coolant warning light



g.

Tachometer with built in hour meter



h.

Dash mounted digital clock



i
.

Coolant temperature gauge



j.

Cruise Control



k.

Dual air pressure gauge w/bar
-
coded indicators.



l.

High temp./low oil pressure engine warning buzzer.



m.

Transmission temperature gauge.


18.

STEERING




Must be full power with gear driven hydraul
ic pump. Tilt
telescoping steering column with 18" diameter, two
-
spoke,
padded steering wheel.


19.

TIRES




21


Tubeless radial tires 11R
-
22.5 with H ply rating hi
-
way tread
front and rear.


20.

TOW HOOKS





Two front and two rear, tow hooks must be fram
e mounted.


21.

TRANSMISSION





Allison 3000 PTS automatic transmission, 5 Forward speeds, overdrive and
reverse.





22.

WHEELS





Hub
-
pilot, steel 8.25x22.5, 10 stud Disc, single front, dual rear.
Oil lubed front wheel bearings.
Wheels are to be po
lished
aluminum
.





BODY REQUIREMENTS


1.

ACCESS PANELS



Interior



A 18"x22" access panel between the davenport seats is
provided for engine service. The panel is removable from inside
the body.







Exterior



Electrical Terminal: 27.5" x 21.75 hinge
d door located exterior
below driver's windows for access to body electrical junction,
terminals and circuit breakers. Door must have retainer to hold
in open position.



Right Front: 19" x 15 1/2" hinged door to permit access to
heater air intake scree
n, air restriction indicator and wiper
motor.



Left Front: 19" x 15 1/2" hinged door to permit access to
windshield washer reservoir, power steering reservoir and wiper
motor.



All access panels must include keyed, locked latches.


2.

AIR INTAKE





Hea
ter intake must be on right front below the windshield level
is electrically controlled. Manual driver fresh air vent must be
located on the left side by the driver’s feet.


22


3.

COMPARTMENTS





Battery



Enclosed sliding tray 23 1/2" x 15 1/2" with locki
ng hinged door.





Engine



Top hinged, aluminum perforated door with gas lift assist
cylinders installed at rear providing access to engine for service.





Glove Box



An 11” x 6 1/2” door above windshield on right side with
door and latch must be pro
vided for driver storage.


4.

CONSTRUCTION






a.

THIS UNIT MUST MEET 2003 FMVSS JOINT STRENGTH
REQUIREMENTS.




b.

All body parts must be thoroughly rust
-
proofed after
fabrication and before assembly.



c.

Body must be fully undercoated
before

moun
ting to the
chassis



d.

Outside side panels must be constructed of 16
-
gauge
smooth

steel. Side panels must extend from below the side
windows to a distance of 16 1/4" below the floor (16 1/4"
skirt).




5.

DEFROSTER





Sufficient defroster warm air ou
tlets/snorkels must be provided
to keep windshield and driver’s window, free of fog, snow, and
ice.


6.

DOORS






Emergency



To be located left side, including upper tempered green tinted
safety glass. A 5" fire
-
block upholstered

header pad with a

teles
copic prop support attached to the top inside of the
emergency door to hold it open at approx. 95°is to be included.
A Slide
-
bolt security latch with an audible alarm must also be
included to warn the driver if the lock is activated after the
engine is ru
nning.



Entrance

Entrance door must be ball bearing suspended, outward opening, two
-
panel
door and seal against outside edge of lower step when door is shut. Door

23

installation with
air
-
powered

controls for opening and closing the door.
Doors are to b
e activated a by means of an air cylinder with an electrically
controlled valve assembly over the door and a rocker
-
type switch, RH
mounted accessible to the driver. Door must be
laminated green tinted

glass. A 4" fire
-
block
upholstered

header pad over t
he interior of the
entrance door along with a stainless steel assist rail at the rear of the
stepwell. Keyed lock mechanism which includes a deadbolt from the door
panel to the header above the entrance door.


7.

ELECTRICAL (accessory)





Power Socket
Accessory with Cap must be provided.


8.

FENDERS





Front and Rear fenders, black rubber

9.

FLOOR






a.

3/16" thick ribbed
gray rubber in aisles and at entrance aisle
area. Aluminum aisle trim over joint in floor covering, full
length of body



b.

1/8
" Smooth gray rubber. Cove molding at wall is to be galvanized steel.



c.


Front and rear molded black smooth rubber wheelhousing.
Galvanized steel wheelhouse trim.



d.

5/8” treated plywood sub floor, attached with screws.


10.

HEADROOM





Full 78", ove
r floor covering and 5/8" plywood sub floor,
measured at center aisle.


11.

HEATER/DEFROSTER







a.

90K BTU front system with continuous
defroster duct under windshield and driver window.



b.

6” fan mounted to wire molding, located in the upper left,
ab
ove driver’s window.




6” fan mounted to windshield header, center of body.



c.

12K BTU driver heater at left under driver seat, single speed
fan



d.

50K BTU, floor mounted, mid
-
ship minimum
.

Dual fans with
separate 2
-
speed motors (must have washable f
ilters)



e.

Two (2) 50K BTU, rear floor mounted minimum, One (1) LH
and one (1) RH. Dual fans with separate 2
-
speed motors
(must have washable filters)



f.

Heater water booster pump must also be installed



g.

Dual ball type heater cut
-
off valves must b
e provided to
isolate heater system from engine / radiator.


24



h.

Manual ball type water flow control valve on heater next to
driver must be provided, for temperature control.



i.
Goodyear Hi
-
Miler heater hose with constant torque clamps
at all joints.
Includes all heater hoses and hose clamps
within the body heater system.



j. Electrically controlled water regulating valve.


12.

INSULATION





The roof front and rear (including corners & roof bows) are to be
insulated with polyester insulation. Si
des are insolated with 1
1/2"" thick high density mineral wool.

Sound deadening
and vibration reducing material shall be sprayed on unexposed
surface of interior and exterior roof panels.



Perforated acoustic
headlining panels spanning the entire length
of the bus.

13.

LETTERING





All lettering must include:
MANHATTAN
-
OGDEN USD 383

on both sides

required by Kansas State law to include 6” bus # on 4 sides. Custom
graphic design to be determined after award of bid.


14.

LIGHTS






a.

Back
-
Up
LED

-

two 4" clear right and left rear.



b.

Clearance
LED

-

two amber front and two red rear single.
Switch to operate clearance, cluster and side marker lights
.



c.

Cluster
LED

-

three amber front and three red rear
with
shields.



d.

Daytime Running
-

Hea
d lamps, tail, license plate, parking,
clearance & marker lights activated when engine is running.




e.

Directional
LED
-

two 7" front amber with directional arrow.
Two 7" amber lights with directional arrow mounted on rear.



f.


Side Directiona
l
LED


Amber sealed shock mounted, side
directional mounted at front belt line area.



g.

Dome
-

Two rows equally spaced at center over aisle, two
switches, left and right with a separate switch for the
rearmost 2 lights. Driver’s dome light to be activat
ed with
separate switch.



h.

Headlights
-

Four rectangular, Halogen single
-
sealed beam.



i.

Side Marker
-

Amber right and left intermediate side marker lights.



j.

Interior and exterior
LED
stepwell light to operate with ID lights when




entrance door

is open.



k.


Stop and Tail
LED
-

Two combination lights, 4” right and left
rear license panel in combination with 7" stop and tail lights
with clear red lens.


25



l.

Engine comp.
-

Two red lights, activated with the hazard
lights, visible when door is open
.



m.

White flashing roof strobe mounted approx. 4' from rear.



15.

MIRRORS


REMOTE/HEATED





Exterior

Mirror Lite High Definition™ Cross View mirror system.. The crossview
mirror system must have a 10.8" x 12.5" elliptical mirror with tinted upper
por
tion to reduce glare. The mirror mounting posts must be attached to the
front cowls.



Rearview

Mirror Lite “Viewmaster” non
-
detent rearview mirror system. The Rearview
mirror must have 7.75” x 10” of flat mirror lens tray on the upper portion, and
7.75”

x 7.75” mirror of lens tray on the lower portion. LH bracket must
contain a grab handle
-
type arm for viewing mirror through the driver’s
window. Both the LH and RH brackets must be non
-
breakaway overhead
-
type arm for viewing mirrors through the windshie
ld.



Interior



10" x 30” with clear safety glass with padded edges.


16.

MUD FLAPS





Required front and rear mud flaps


17.

PAINT






Exterior


Custom 2
-
tone paint, White on Navy Blue with paint scheme to be
determined after award of the bid.



I
nterior



White, hot sprayed
-
on baked enamel,

.


18.

RADIO






AM/FM/PA/CD with 8 deluxe speaker system.


19.

REFLECTORS





a.

Two 3" red mounted on side of body near rear installed with screws.



b.

Two 3" red, mounted on rear of body installed with

screws.



c.

Two 3" amber right and left intermediate side reflectors installed with




screws
.





26

20.

REFLECTIVE TAPE





a.

3M Diamond Grade tape one
-
inch minimum width strip must
surround each emergency exit, 1 3/4” wide rear structure,
and 2” wide st
rip on each side of unit at approximately floor
level.


21.

SAFETY EQUIPMENT





a.

Fire extinguisher


5lb. Dry with hose



b.

24 unit standard first aid kit



c.

Triangular warning devices


floor mounted



d.

Body fluid clean up kit



e.

Reverse activat
ed back up alarm



f.

Locking toolbox with lid



g.

Roof vent/hatches, two (2), must be installed in body roof,
with buzzer to driver’s area.


22.

SEATS






a.

Driver's





National 2000 high back air suspension, gray
, with seven
inch fore and aft travel and five inch vertical adjustment.
Seat belt must be three
-
point, floor mounted anti
-
cinch
emergency locking retractor. An adjustable pillar loop
providing approximately 7 1/2” vertical adjustment at the
shoulder bel
t top mount must be installed.
Driver’s armrest
must be to the left of driver on rear portion of switch panel.
Flip up style armrest mounted aisle side.



b.

Upholstery




All Passenger seats must be upholstered in level 5 fire
-
block
material. Gray mater
ial.



c.

Passenger seats




Coach Style
Activity seating: split back/bench design for two
(2) passengers with aisle side armrest and contoured lumbar
support.



23.

STEPWELL





Straight
-

3 step, 24 3/4" depth galvanized steel. Black step
treads
non
-
abrasive with white nosing. 3” white rubber wear
plate is located at the floor level step of the entrance door.
Stepwell design must be designed to National standards 1990.


24.

SUN VISOR





Transparent dark green tint 6.5" x 30" smooth edge plastic
,
located in front of driver.


27


25.

SWITCH PANEL





Mounted on left of driver with rocker
-
type, illuminated
switches for electrical equipment. Brightness of
illumination must be controlled by an additional rheostat
switch.


26.

VENTILATION





Static n
on
-
closing type in front roof.


27.

WINDOWS





Driver's

Double sliding
black
sash with security fastener for locking both sashes,
laminated, tinted s
afety glass.



Side

12" split sash,

tempered tinted
glass in
black
frame, provides 12" opening
when lowere
d. Push out windows each side, 2RH/2LH, with buzzer to
driver’s area.

MUST BE TINTED AND TEMPERED.




Rear Vision



Tinted tempered and bonded into the structure.


28.

WINDSHIELD





Two
-
separate pieces of flat
shaded

safety plate glass bonded
into the st
ructure. Grip handles mounted on both sides with
fold
-
up steps, right and left cowls, to facilitate cleaning of the
windshield.


29.

WINDSHIELD/WIPERS





Electric, intermittent single switch, wet a
rm wipers. Bottom
mounted with remote control, non
-
glar
e arms and blades.
Electric windshield washer with hard plastic one
-
gallon capacity
reservoir located under engine hood, washer outlets mounted
on wiper arms.


30.

WIRING






Colored and continuously number coded in composite molding
on top of side windo
ws for access to harness without removing
window. Body wiring protected by automatic resetting circuit
breakers.


31.

AIR CONDITIONING


Air conditioning system with roof mounted condenser. System must


28

have a minimum BTU output of 180,000. Minimum 41
ci Transit
Compressor. Interior shall be ducted with diffusers at each seating position.
Include dual position reading lights above every passenger.


32.

LUGGAGE



Luggage compartments, pass
-
through, under full width of bus
body, forward of rear axle, 15
1.8 cu. ft., locking doors and lights.
Individual doors with gas springs for ease of operation.


33. VIDEO SURVEILLANCE SYSTEM





Safety Vision SVR
-
4100 Mobile Digital Video Recorder
System to include: recording four video and four audio
channels
in H.264 format with recording from four cameras;
ability to retrieve data wirelessly or manually and monitor GPS
positioning, speed tracking and recording, and vital information
for each recorded event. DVR must be inside a lockable box
and have cooling
fans wired to run when the DVR is powered
on.



Include two (2) SV
-
830 DOME high resolution day/night
vision color cameras with 1/4
-
inch CCD 8.0 mm wide angle
lens, 420 TVL, and NTSC standard signal format built for
mobile applications


one on the front i
nside bus header and
one on the rear inside bus header.



Include one (1) SV
-
830 DOME high resolution day/night
vision color camera with 1/4
-
inch CCD 8.0 mm wide angle
lens, 420 TVL, and NTSC standard signal format built for
mobile applications to be place
d above the driver to record the
driver position and service door.



Include one (1) SV
-
830 DOME high resolution day/night
color camera with 1/4
-
inch CCD 8.0 mm wide angle lens, 420
TVL, and NTSC standard signal format built for mobile
applications to be p
laced facing out the front windshield.



Included with Video System is one 32GB Compact Flash
Card.


34.

TRAINING



Successful bidder must provide mechanical training/service school
pertaining to the bus being
quoted. Service school must be offered bian
nually at
a minimum,
a
nd consist of approximately 14 hours of classroom instruction.


35. WARRANTY




5
year/unlimited mileage warranty covering all workmanship and materials on
body, engine, transmission and A/C components.
Towing cover
ed first two
years.


29




PLEASE NOTE:

These specifications represent the minimum
specifications acceptable to the district. Any deviation here to must be
specifically identified in the COMPLY column of the specifications and
described on an attached sheet.

Failure to do so will result in the rejection
of your bid and/or your product for reason of non
-
compliance with our
invitation.


All specifications, whether listed or not, must meet or exceed all State and
Federal regulations now in effect.

Should the b
idder take any exceptions to these specifications, they must be so
stated on a separate sheet and

accompany bid.


Should the bidder take any exceptions to these specifications, they must be so
stated on a separate sheet and accompany
proposal
.


Delivery
date must be stated at time of
proposal
.


30


RESPONSE
SUMMARY


RFP

NO. P
1
314
-
V
-
1

NEW/USED SCHOOL BUSES

DUE:
OCTOBER

24, 201
3

AT
1
:00 P.M.

****************************************************************************************

We have read all guidelines sta
ted in the notice to bidders and submit this quotation in
accordance with stated conditions.


Authorized Signature ___________________________ Date: __________
__


Printed Name
____________________________________________________


Company representing
__________________________________________
__


Address ______________________________________________________


Telephone number (___) _____________ Fax number (___) ____________



Email _____________________________


State Contract Number (if applicable) _
_________________________________

*******************************************************************************************
******

Award will be made based on which buses are the best value for the district; this may
consist of new and used buses and/or b
uses from two vendors.


NEW or
MILEAGE

YEAR, MAKE and MODEL

Price

Type “C” 71 pass.




Type “C” 71 pass.




Type “C” 71 pass.




Type “C” 71 pass.




Type “A” 21
-
㌰P
pa獳snger




Type “
A


-


p
a獳snger




Type “D” activity
bus





A 獥捯nd res
pon獥 獵mmary 獨eet may be atta捨ed if your propo獡l in捬ude猠both new
and used type “C” 71 passenger buses.

***************************************************************************************************

*** Please attach your current W9 to your prop
osal ***