Chilled Water Optimization in a Thermal Plant

stagetofuΤεχνίτη Νοημοσύνη και Ρομποτική

29 Οκτ 2013 (πριν από 4 χρόνια και 8 μήνες)

263 εμφανίσεις

Chilled Water Optimization in a Thermal Plant

There are three types of HVAC systems that utilize water as a heat transfer medium:

1. The first system, which is used for cooling in dry climates, is called the “Swamp Cooler.”
system employs a fan that blows outdoor air or return air over a revolving drum. The drum is
covered with a sponge
like material and the lower portion of the drum is immersed in water. As
the air passes over the drum, the air temperature is lowered, a
nd the relative humidity of the
air is increased as water on the drum evaporates. This evaporation process will remove 760
BTU per pound of water evaporated. However, as mentioned earlier, the process only works in
dry climates where the air has moisture c
ontent that is low enough to allow it to accept the
additional moisture from the evaporation process.

2. The second water
based system uses a constant source of water at a temperature of 80°F or
less to condense the refrigerant vapor in a standard mechani
cal refrigeration circuit. This water
is called condenser water. This type of unit is known as a packaged water
cooled air
conditioner. Condenser water is normally provided by a mall or a large building for use by its
tenants. The building then maintains
a cooling tower that is used to cool the condenser water
and pumps that are used to circulate the water. This type of system is used where there is
limited access to outdoor areas such as roofs for placement of outdoor equipment. We will deal
with water
oled systems in detail in a future article.

3. The third type of water based air conditioning system is called a chilled water system. Chilled
water systems utilize a constant source of water at a temperature of approximately 45°F. This
water can be provi
ded by a central building chilled water plant, an off
site utility that sells
chilled water, or by the tenant’s own packaged chiller. Most retail stores with less than 40,000
square feet of floor space do not have their own chillers and depend on Landlord
chilled water.

For our purposes, let’s assume that the Landlord is providing an uninterruptable source
of 45°F chilled water to the building. This water is distributed throughout the building via a
piping network. The large horizontal pipes are c
alled mains, the small piping leading to each
tenant space are called branches, and the vertical runs are called risers. The chilled water piping
is heavily insulated and the insulation is covered with a vapor barrier, which is impervious to
moisture. Thes
e pipes are carrying a low temperature liquid, and if they were left un
moisture from the air would condense on the outside of the pipes and drip onto anything
below the piping. In addition, heat would be transferred to the piping from the air r
esulting in
wasted energy and a rise in the chilled water temperature. One or more air handlers serve each
tenant. An air handler is a sheet metal box that contains a fan and a cooling coil. The cooling
coil is made of copper tubing bent into a serpentine
shape with aluminum fins bonded to the
copper tubing to increase the heat transfer area. The air handler also contains air filters that
remove impurities from the air that is being drawn over the coil by the fan. The fan is also
called a blower. A motor dr
ives the blower via a drive belt that has a V section. The air handler
may also be furnished with a heating coil that adds heat to the air when heat is required. Most
chilled water air handlers contain a section called a mixing box. The mixing box is a she
et metal
section with two openings in it. There is a duct connected to each opening and a damper
located within each opening. One duct is used to bring return air from the conditioned space
back to the air handler. The second duct is connected to the outdo
ors and is used to introduce
outdoor air for ventilation purposes. Operation of a system like this is simple. The fan runs
continuously, drawing a mix of outdoor air and return air through the air filters. The air is then
heated or cooled as it passes over

hot coils or cold coils. Chilled water flow to the cooling coil is
controlled by a motorized valve. If the space temperature is at or below the set point of the
thermostat, the motorized valve closes. If the thermostat is not satisfied, the motorized valv
opens causing chilled water to flow through the coil. If the air handler is equipped with a hot
water heating coil and a chilled water
cooling coil the system is known as a four
pipe system. In
some buildings, the same coil is used for both heating and c
ooling. During the cooling season,
chilled water is circulated through the piping system that serves the air handlers and during the
heating season, hot water is circulated through the system. This is known as a two
pipe system.
Sometimes heat is provided
by an electric resistance coil, a steam heating coil, or a gas fired
duct furnace instead of being provided by hot water. Most chilled water air handlers are
installed with outdoor air ducts that can deliver the full volume of air the unit is designed to
irculate. This oversized outdoor air duct, the mixing box, and the addition of certain controls,
forms the components required for an economizer cycle. When outdoor air temperatures are
below a threshold value of approximately 55°F, outdoor air may be used

for cooling in lieu of
using chilled water. This is an energy saving device in four pipe systems and a necessity in two
pipe systems. In buildings with two
pipe systems, the building may be circulating hot water in
an attempt to provide heat, while some s
paces with high internal loads require cooling. Under
these circumstances, outdoor air is the only medium available to provide cooling.

The most common problem we find with chilled water systems is insufficient water flow to
individual air handlers. In a m
all, for example, the piping to each tenant’s air handler forms a
parallel path between the supply and return mains. Water will follow the path of least
resistance; therefore, the more resistance to flow (friction) in each path, the less water will flow
rough that path. The total resistance to flow in any path is a function of the length of run, the
diameter of the piping, the resistance of the coil, and the resistance of the valves and fittings.
Distance from the pump also plays a role, as does the pipin
g layout. Balancing valves are
installed on each branch to add resistance to flow in order to guarantee that each branch
receives the volume of water it was designed to handle.

The next most prevalent problem is dirty chilled water coils. Air handlers have

a usable life span
of up to 30 years. Over time, chilled water coils become obstructed with airborne dirt that
renders them inefficient. Unlike mechanical refrigeration units, which freeze
up and leak when
the indoor coils get plugged, chilled water coils

just become less and less efficient until they
reach a point where they cannot deliver enough capacity to cool the space.

Normally chilled water is delivered into the piping system at a temperature between 42°F and
46°F. This is the water temperature that

should be present at the supply connection on the air
handler. Some buildings vary the temperature of chilled water with outdoor temperature
change. This is called reset. In an effort to save energy, a building may install a control system
that resets the

chilled water temperature upward as the outdoor temperature drops. The

that as outdoor temperatures decrease there is less of a need for cooling and the
cooling requirements can be met with higher temperature water or less water. They may
r 42°F water at 95° outdoor temperatures and 50° water at 65° outdoor temperatures.
Unfortunately, in a retail store the load on a 65°F day may be almost as great as the load on a
95°F day. When the building resets the chilled water temperature, the store
insufficient cooling.

Optimizing the Plant:

Optimizing the Plant will manage the chiller plant with specialized control algorithms. These
algorithms require the conversion of constant speed condenser pumps, chilled water pumps,
and cooling tower f
ans to variable speed through the installation of Variable Frequency Drives
(VFDs). The VFDs allow the Demand Flow algorithms to maintain optimal differential system
pressure, reduce excessive pumping energy, reduce equipment runtime and increase system
liverable tonnage on systems suffering from a diminished refrigeration effect. The
Optimization Controller automatically optimizes all plant functions. Typically, system access to
the system will be available through a unique Graphical User Interface (GUI)
. Siemens Web
Based EMC software enables chiller plant system performance monitoring from anywhere in
the world via the Internet. EMC is responsible for data accumulation, reporting energy profiles,
and detailing equipment operating parameters.

Currently w
e have 9 chillers in the North
Thermal Plant and 5 chillers at the Bass Thermal Plant.

Fig 1 NTEP chiller Data

Fig 2 BTEP chiller Data

Fig. 3: Configuration of Chilled Water System.

Currently equipment is operated independently with local PID tempe
rature and pressure loops.
Chillers and towers are sequenced to keep on
line equipment as fully loaded as possible. Plant
optimization, if it is applied at all, requires another level of control that continuously resets the
various set points, which can re
duce overall system stability. Constant Speed Chiller Efficiency is
nearly constant between 60% & 100% loading, the Efficiency of Variable Speed Centrifugal
Chillers increases dramatically as load falls in that range. The Efficiency of Variable Speed
ifugal Chillers is more significantly improved by the reduction in Condensing Water
Temperature. Equipment is connected via an integrated network and operation is coordinated
to maintain lowest overall energy use at all load conditions using demand based c
ontrol and
natural curve sequencing of equipment. Unless incorporated as design criteria, temperature
and pressure set points are not employed except as operating limits.

Valve Control: Multivariable "Intelligent Iterative Control" is used whereby valve a
djustment is
based on set point error, pump speed, chilled water temperature, and current valve position.

Pump Control:

"Orifice area" pump speed control adjusts speed based on percent of total valve orifice area
currently open and further adjusted by the
number of valves nearly wide open. Pump
Sequencing is based on "natural curve" principle.

In order to control these pumps VFD are essential. This device uses power electronics to vary
the frequency of input power to the motor, thereby controlling motor speed. A VFD is the ideal
soft starter since it provides the lowest inrush of any starter typ
e as shown in Table B. Unlike all
other types of starters, the VFD can use frequency to limit the power and current delivered to
the motor. The VFD will start the motor by delivering power at a low frequency. At this low
frequency, the motor does not requi
re a high level of current. The VFD incrementally increases
the frequency and motor speed until the desired speed is met. Given that the load is always
driven by the air handlers in the building there is no need to run the pumps on the rest of the
t at 100% all time. Therefore VFD allows the modulation of motors

to ramp down
with demand.
This will allow us to save energy, maintenance and longevity