10_EX04_Determining

reekydizzyΔίκτυα και Επικοινωνίες

28 Οκτ 2013 (πριν από 3 χρόνια και 9 μήνες)

100 εμφανίσεις

Thanyapon

S. ,
ThaiAdmin

Trainer Team



Dynamic Routing Protocol


Configurations


RIP


IGRP


OSPF

Ex04
-
1

640
-
802 CCNA

Thanyapon

S. ,
ThaiAdmin

Trainer Team


Upon completion of this exercise, you will be
able to perform the following tasks:


Configure Dynamic routing protocol for RIP, IGRP,
OSPF


Verify configuration of RIP, IGRP, and OSPF

Ex 04
-
2

640
-
802 CCNA

Thanyapon

S. ,
ThaiAdmin

Trainer Team

640
-
802 CCNA

Ex 04
-
3

1
.
Create network as shown in the network diagram

Thanyapon

S. ,
ThaiAdmin

Trainer Team

2. Assign IP address, subnet mask of the routers


as shown in the network diagram

3. Assign clock to the serial interface of all router.


(only for DCE interface)

4. Configure IP address, subnet mask, default gateway of


the PC A ,PC B and PC C to the appropriated value.

5. Test ping from PC A
-
> PC B, and PC A
-
> PC C

6
. Configure
rip on three routers

7. Verify routing table of each router.

8
. Test ping from PC A
-
> PC B

9.
(clear routing protocol) Try using
IGRP,and

OSPF


640
-
802 CCNA

Ex 04
-
4

Thanyapon

S. ,
ThaiAdmin

Trainer Team

At Router 1

Router1#

conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router1(
config
)#

interface e0

Router1(
config
-
if)#

ip

addr

192.168.1.1 255.255.255.0

Router1(
config
-
if)#

no shutdown

%LINK
-
3
-
UPDOWN: Interface Ethernet0, changed state to up

Router1(
config
)#
interface s0

Router1(
config
-
if)#

ip

addr

10.1.1.1 255.255.255.252

Router1(
config
-
if)#

clock rate 64000

Router1(
config
-
if)#

no shutdown

Router1(
config
-
if)#

exit

Router1(
config
)#

router rip

Router1(
config
-
router)#

network 192.168.1.0

Router1(
config
-
router)#

network 10.0.0.0

Router1(
config
-
router)#

end


640
-
802 CCNA

Ex 04
-
5

Configure RIP

On specified
network

Thanyapon

S. ,
ThaiAdmin

Trainer Team

640
-
802 CCNA

Ex 04
-
6

Step 7: Verify routing table on Router1

Router1#

sh

ip

route

Codes: C
-

connected, S
-

static, I
-

IGRP, R
-

RIP, M
-

mobile, B
-

BGP


D
-

EIGRP, EX
-

EIGRP external, O
-

OSPF, IA
-

OSPF inter area


E1
-

OSPF external type 1, E2
-

OSPF external type 2, E
-

EGP


i

-

IS
-
IS, L1
-

IS
-
IS level
-
1, L2
-

IS
-
IS level
-
2, *
-

candidate default


U
-

per
-
user static route

Gateway of last resort is not set


10.0.0.0/30 is
subnetted
, 2 subnets

C 10.1.1.0 is directly connected, Serial0

R 10.1.1.4 [120/1] via 10.1.1.2, 00:03:18, Serial0


192.168.1.0/24 is
subnetted
, 1 subnets

C 192.168.1.0 is directly connected, Ethernet0


192.168.2.0/24 is
subnetted
, 1 subnets

R 192.168.2.0 [120/1] via 10.1.1.2, 00:06:40, Serial0


192.168.3.0/24 is
subnetted
, 1 subnets

R 192.168.3.0 [120/2] via 10.1.1.2, 00:04:19, Serial0

Network
learned by
RIP

R= RIP

Thanyapon

S. ,
ThaiAdmin

Trainer Team

640
-
802 CCNA

Ex 04
-
7

Command

Usage

Router
<protocol> <option>

Enable dynamic routing protocol as
specified


network
<network no.>
<option>

Select network to participate the routing
protocol

Show
ip

protocols

Displays dynamic routing protocol
information

Debug
ip

rip

Enable route to display the RIP routing
update

Debug
ip

igrp

transactions

Display IGRP transaction information

Debug ip igrp events

Displays IGRP events as they
occour

No debug all

Turns off all debugging display

Show
ip

ospf

neighbor

Display OSPF neighbor information

Thanyapon

S. ,
ThaiAdmin

Trainer Team

Ex 04
-
8

640
-
802 CCNA