Elite Type Series Booklet - version 14 . 02 . 07

possumneckvegetableΛογισμικό & κατασκευή λογ/κού

4 Ιουλ 2012 (πριν από 5 χρόνια και 2 μήνες)

671 εμφανίσεις

Type Series Booklet
Elite
50Hz 60Hz
Pump sizes
Flow
up to
340L/s 288L/s
Head
up to
140m 108m
Temperature
up to
Speed
up to
2900 rpm 3600 rpm
Pressure
up to
KSB Australia Pty Ltd
1600kPa
Centrifugal Pump
32mm to 250mm
95
o
C
Application
The Ajax Elite centrifugal pump is suitable for handling
water and similar liquids mainly used in the following
applications.
-Water Supply
-Air conditioning
-Irrigation
-Pressure boosting
-Fire Protection
-Heating and ventilating
-Industrial
Designation
E 150 - 40 A 20 C
Type
Discharge diameter mm
Nominal impeller diameter cm
Mechanical arrangement
Shaft sealing
Materials of construction
Design
Horizontal, single stage, end suction centrifugal pump,
complying with the requirements of EN 733 (DIN 24255).
The back pull out design allows for easy maintenance and
repair as the rotating element may be removed without
disturbing the system pipework. Removal of the rotating
element is facilitated by the lifting eye on the bearing
housing.
Operating Data
Elite
Selection Chart
1450 rpm
Selection Chart
2900 rpm
Note:
For final selection
refer to individual
performance
curves
Note:
For final selection
refer to individual
performance
curves
2
Elite
Absorbed Pump
Shaft [kW]
Driver Power
Reserve
Approx. 20%
Approx. 15%
Approx. 10%
Up to 7.5
7.5 - 40
Above 40
Construction
Horizontal,single stage,end suction with vertical
discharge,complying with the requirements of EN 733
(DIN 24255).Most models are suitable for 1600kPa (16
bar) pressure except for larger pumps that are rated fo
r
1000kPa (10 bar).The pull back out design allows for the
maintenance of the pump without disturbing the pipework
connected to the casing, or the pump alignment.
Flanges
Pump flanges have raised faces and are to standards
AS/NZS 4331.2,ISO 7005.2 16 bar.Gauge tappings are
provided on suction and discharge flanges as standard.
Impellers
The shrouded impellers have front seals and,either back
vanes or rear seals with balance holes to provide hydraulic
balance.Impellers are dynamically balanced,are keyed to
the shaft and are located axially between the sleeve and
impeller nut.Zinc free bronze impellers are fitted as
standard.
Casing
All pump casings are cast iron and radially split to permit
removal of the rotating element.The vertical centre line
discharge makes the casing self venting.Zinc free bronze
wear rings are fitted as standard.
Shaft
Stainless steel shafts are standard and are ground to fit
the impeller, sleeve, bearings and coupling.
Bearings
Grease Lubrication – Standard
Oil Lubrication – for high speed models (EH)
Max. Pump Temperature 95
o
C
The Bearing arrangement consists of two identical single
row deep groove ball bearings which are grease lubricated
through grease nipples located in each bearing cover.
Shaft Seal
The shaft sealing is carried out by means of mechanical
seal with the option of packed gland.
Mechanical
Seal
- A single mechanical seal,with a
ceramic stationary face and carbon rotating face is fitted as
standard.The standard seal elastomer is nitrile and is
suitable for up to 95
o
C temperature applications.The other
seal components are AISI 304 stainless steel.
Options: Balanced seal – option M1
Cyclone separator – option S1
Gland
Packing
- Fitted with removable lantern ring and
square plaited packing.Packing is fitted over the sleeve to
prevent shaft wear.
Painting
Prior to painting,the pump is thoroughly cleaned of scale,
weld splatter and any other foreign material.The pump is
then painted with a high quality industrial enamel paint.
Accessories
Drive
The pump is only recommended for direct drive via a
flexible spacer coupling.Spacer couplings enable the
utilisation of the back pull out feature.
Where belt drives are necessary a separate jack
(intermediate) shaft with bearings to carry the belt loads
may be required.
All drive systems,where supplied by KSB Ajax,are
appropriately protected by suitable guards.
Baseplate
Baseplates for electric drives are available in a variety o
f
styles:
Standard
- Fixed and grouted directly to the foundation.
Anti Vibration
- Rigid baseplate on rubber mounts.
- Rigid baseplate on spring mounts.
- Rigid baseplate with inertia block base and
spring mounts.
The baseplate is manufactured or fabricated from either
cold formed (pressed) steel plate or from rolled steel
channel sections.
Pump Selection
For pump selection the hydraulic performance curves
should be used.These curves are based on water at
15
o
C and SG equal to 1.0.
NPSH values are indicated on the performance curves.
At least 0.5m should be added as a safety margin.
To overcome variations between actual and design
system requirements it is recommended that the drive
r
power exceeds the absorbed pump shaft power.
3
Elite
Standard Seal Option M1
Pressure Maximum operating pressure* 1400kPa 1400kPa
Maximum hydrostatic test pressure 2100kPa 2400kPa
Maximum suction pressure 1450rpm 900kPa 1000kPa
Maximum suction pressure 2900rpm 700kPa 1000kPa
Temperature Packed gland
Mechanical Seal: Standard
Mechanical Seal Balanced: Option M1
Speed Maximum Speed*
*refer tabular listing on page 5.
Australian American EN
Casing
Back Cover
Bearing Housing
Bearing Cover
Lantern Ring
Wear Rings (Option)
Impeller
Wear Rings
Bronze
AS1565-C83600 ASTM B584-C83600 -
Shaft
Shaft Sleeve
Part Mechanical Seal Packed Gland Packed Gland
Description Code 04 (A20C) Code 07 (AXOC) Code 09 (AXOJJ)
Casing Cast Iron Cast Iron Stainless Steel
Impeller Zinc Free Bronze Zinc Free Bronze Stainless Steel
Wear Rings Zinc Free Bronze Zinc Free Bronze Stainless Steel
Shaft Stainless Steel Stainless Steel 420 Stainless Steel
Shaft Sleeve Not Fitted Stainless Steel Stainless Steel
Spring Sleeve Stainless Steel Not Fitted Not Fitted
Lantern Ring Not Fitted Cast Iron Stainless Steel
Lantern Ring Bush Not Fitted Bronze Stainless Steel
Gland Not Fitted Cast Iron Stainless Steel
Seal Plate Cast Iron Not Fitted Not Fitted
Part
Description
Seat Ceramic Silicon Cabid
Seal Face Carbon Carbon
Seal O Ring Nitrile Nitrile
Bellows Nitrile Nitrile
Retainer
Drive Band
Spring Holder
Spring
Stainless Steel
AS2837 GR.420
AS2837 GR.316
AISI Type 420
AISI Type 316
X20CR13
X10CRN1MOT118/10
BS970:420/S37
BS970:316
CC480 K - GC
British
Lantern Ring Bush
AS1565-1985
Alloy C90250
BS 1400-1973
CT1
906D
BS1400-LG2
Cast Iron
Zinc Free
Bronze
Material Component
Packed Gland
JL 1030
Mechanical Seal
Nearest Equivalent Standard
AS1830/T220
ASTM A48
Class 30
BS1452: GR220
-20
o
C to 95
o
C
-20
o
C to 95
o
C
1600kPa
Stainless Steel
AISI 316
Standard
Stainless Steel
AISI 304
2100kPa
600kPa
400kPa
High Pressure
Option M1
-20
o
C to 95
o
C
3600 rpm
ASTM
C 90700
General Operating Parameters
Material Specifications
Pump Material Combinations
Mechanical Seal Materials
4
Elite
rpm/imp. dia Front Rear Bronze Impeller bar kPa PSI bar kPa PSI
E32-13 3450/134 6305 6305 0.004 21 2100 304 16 1600 232
E32-16 3450/156 6305 6305 0.006 21 2100 304 16 1600 232
E32-20 3450/181 6305 6305 0.015 21 2100 304 16 1600 232
E32-26 3450/220 6305 6305 0.043 21 2100 304 16 1600 232
E40-13 3450/130 6305 6305 0.004 21 2100 304 16 1600 232
E40-16 3450/156 6305 6305 0.006 21 2100 304 16 1600 232
E40-20 3450/186 6305 6305 0.019 21 2100 304 16 1600 232
E40-26 3450/225 6305 6305 0.048 21 2100 304 16 1600 232
E40-32 2300/329 6307 6307 0.105 21 2100 304 16 1600 232
EH40-32 2900/320 3307 3307 0.105 21 2100 304 16 1600 232
E50-13 3450/132 6305 6305 0.005 21 2100 304 16 1600 232
E50-16 3450/159 6305 6305 0.008 21 2100 304 16 1600 232
E50-20 3450/182 6305 6305 0.019 21 2100 304 16 1600 232
E50-26 3450/227 6305 6305 0.05 21 2100 304 16 1600 232
E50-32 2300/328 6307 6307 0.111 21 2100 304 16 1600 232
EH50-32 2900/314 3307 3307 0.111 21 2100 304 16 1600 232
E65-13 3450/159 6305 6305 0.006 21 2100 304 16 1600 232
E65-16 3450/159 6305 6305 0.009 21 2100 304 16 1600 232
E65-20 3450/184 6305 6305 0.019 21 2100 304 16 1600 232
E65-26 3450/224 6307 6307 0.052 21 2100 304 16 1600 232
E65-32 2400/329 6307 6307 0.127 21 2100 304 16 1600 232
EH65-32 2900/316 3307 3307 0.127 21 2100 304 16 1600 232
E80-16 3450/160 6305 6305 0.013 21 2100 304 16 1600 232
E80-20 3450/191 6307 6307 0.024 21 2100 304 16 1600 232
E80-26 3450/230 6307 6307 0.05 21 2100 304 16 1600 232
E80-32 1800/329 6307 6307 0.107 21 2100 304 16 1600 232
EH80-32 2900/318 3307 3307 0.107 21 2100 304 16 1600 232
E80-40 1800/409 6309 6309 0.392 17 1700 246 13 1300 188
E100-16 2900/174 6307 6307 0.02 21 2100 304 16 1600 232
E100-20 3450/193 6307 6307 0.03 21 2100 304 16 1600 232
E100-26 3450/228 6307 6307 0.068 21 2100 304 16 1600 232
E100-32 1800/329 6307 6307 0.156 21 2100 304 16 1600 232
E100-40 1800/409 6309 6309 0.358 17 1700 246 13 1300 188
E125-20 2900/214 6307 6307 0.069 21 2100 304 16 1600 232
E125-26 1800/264 6307 6307 0.076 21 2100 304 16 1600 232
E125-32 1800/329 6309 6309 0.165 21 2100 304 16 1600 232
E125-40 1800/409 6309 6309 0.377 17 1700 246 13 1300 188
E150-20 1800/220 6307 6307 0.078 15 1500 217 11 1100 159
E150-26 1800/264 6309 6309 0.158 15 1500 217 11 1100 159
E150-32 1800/329 6309 6309 0.182 15 1500 217 11 1100 159
E150-40 1800/409 6309 6309 0.4 15 1500 217 11 1100 159
E200-26 1800/264 6309 6309 0.3 15 1500 217 11 1100 159
E200-32 1800/329 6311 6311 0.217 15 1500 217 11 1100 159
E200-40 1800/409 6311 6311 0.441 15 1500 217 11 1100 159
E250-32 1800/329 6311 6311 0.221 15 1500 217 11 1100 159
E250-40 1800/409 6311 6311 0.451 15 1500 217 11 1100 159

Hydrostatic Test Pressure
Maximum
Maximum Working Pressure
up to 120˚C
Pump Model
Maximum Nominal
Speed Direct Coupled
Bearing Type
Mass Moment of
Inertia J Rotating
Assy. Less Coupling
[kg*m
2
]
Pump Technical Data
5
Elite
B.P.O
Bearing
Pump Element
Model Weight [kg]
(Pump Less
Max.Min.Max.Min.Casing)
E32-13* 0.4 0.3 139 100 7 6 61 70 - - - - 20
E32-16 0.4 0.3 174 125 6 6 62 70 - 120 6 3 25
E32-20 0.4 0.3 214 165 6 4 68 80 - 140 8 3 32
E32-26 0.4 0.3 264 205 5 6 70 80 - 200 6 4 43
E40-13* 0.4 0.3 139 100 10 6 71 80 - - - - 20
E40-16 0.4 0.3 175 130 7.5 6 68 80 - 114 8 3.5 25
E40-20 0.4 0.3 214 165 7 6 69 80 - 153 8 3 33
E40-26 0.4 0.3 264 205 6 6 84 95 - 168 8 5 44
E40-32 0.4 0.3 329 255 6 6 77 95 95 - - - 59
EH40-32 0.4 0.3 320 255 6 6 77 95 95 - - - 59
E50-13 0.4 0.3 139 120 16 6 88 95 - 126 6 3 22
E50-16 0.4 0.3 174 135 13 6 85 95 - 164 6 2.5 26
E50-20 0.4 0.3 214 165 10 6 86 95 - 154 8 3 33
E50-26 0.4 0.3 264 205 8 7 94 115 - 189 8 5.5 45
E50-32 0.4 0.3 328 255 7 6 102 115 115 - - - 56
EH50-32 0.4 0.3 314 255 7 6 102 115 115 - - - 56
E65-13 0.4 0.3 139 130 23 7 100 115 - 139 6 4.5 24
E65-16 0.4 0.3 174 125 19 6 102 115 - 139 6 6 28
E65-20 0.4 0.3 214 165 16 6 107 115 - 180 8 4 35
E65-26 0.4 0.3 264 205 13 6 108 115 - 228 8 2 66
E65-32 0.5 0.4 329 255 10 7 114 130 125 - - - 73
EH65-32 0.5 0.4 316 255 10 7 114 130 125 - - - 73
E80-16 0.5 0.4 174 145 25 7 118 130 - 151 8 5 31
E80-20 0.5 0.4 214 165 22 6 121 130 - 186 8 4 46
E80-26 0.5 0.4 264 205 15 7 120 130 - 247 8 4 62
E80-32 0.5 0.4 329 255 13 6 125 140 135 - - - 74
EH80-32 0.5 0.4 318 255 13 6 125 140 135 - - - 74
E80-40 0.5 0.4 409 320 11 7 128 140 160 - - - 107
E100-16 0.5 0.4 174 165 32 7 148 160 - 164 9 4.5 20
E100-20 0.5 0.4 214 175 27 7 142 160 - 208 9 4 50
E100-26 0.5 0.4 264 205 23 7 145 160 - 253 10 5.5 56
E100-32 0.5 0.4 329 255 18 7 144 160 155 - - - 87
E100-40 0.5 0.4 409 320 15 6 147 160 160 - - - 120
E125-20 0.5 0.4 214 190 34 7 167 180 - 205 12 2 62
E125-26 0.5 0.4 264 205 32 6 167 180 - 236 12 3 67
E125-32 0.5 0.4 329 255 23 6 167 180 180 - - - 97
E125-40 0.5 0.4 409 320 20 7 166 180 180 - - - 122
E150-20 0.5 0.4 220 200 57 6 170 185 185 - - - 88
E150-26 0.5 0.4 264 210 39 7 185 200 200 - - - 93
E150-32 0.5 0.4 329 255 31 6 183 200 200 - - - 102
E150-40 0.5 0.4 409 320 26 7 188 200 200 - - - 125
E200-26 0.5 0.4 264 250 68 6 220 235 200 - - - 86
E200-32 0.5 0.4 329 285 50 6 232.5 250 250 - - - 153
E200-40 0.5 0.4 409 335 37.5 7 222 235 235 - - - 180
E250-32 0.5 0.4 329 285 72 6 242 260 260 - - - 190
E250-40 0.5 0.4 409 335 52 6 236 260 260 - - - 237
* no Expeller Vanes
Height
[mm]
Expeller Vane
Eye
Diameter
[mm]
Front Seal
Diameter
[mm]
Back Seal
Diameter
[mm]
Dia. [mm]
[mm]
Diameter
[mm]
Impeller Data
Seal Ring
Diametrical
Clearance
Vane
Width
[mm]
No. of
Vanes
[mm]
No. of
Vanes
Pump Technical Data
6
Elite
Pump Model:Pump Model:
E40-32, E50-32, E65-32, E80-32, E80-40, E100-32,E32-13*, E32-16, E32-20, E32-26, E40-13*, E40-16, E40-20,
E100-40, E125-32, E125-40, E150-20, E150-26, E150-32, E40-26, E50-13, E50-16, E50-20, E50-26, E65-13, E65-16,
E150-40, E200-26, E200-32, E200-40, E250-32, E250-40 E65-20, E65-26, E80-16, E80-20, E80-26, E100-16,
E100-20, E100-26, E125-20, E125-26
Pump Models with clamped back cover:Pump Models with bolted back cover:
E32-13, E32-16, E40-13, E40-16,E32-20, E32-26, E40-20, E40-26, E40-32,
E50-13, E50-16, E65-13, E65-16,E50-20, E50-26, E50-32, E65-20, E65-26,
E80-16, E80-20, E100-16, E100-20, E65-32, E80-26, E80-32, E80-40, E100-26,
E125-20, E150-26, E200-26 E100-32, E100-40, E125-26, E125-32,
E125-40, E150-20, E150-32, E150-40,
E200-32, E200-40, E250-32, E250-40
* no Expeller Vanes
ITEM DESCRIPTION MATERIAL ITEM DESCRIPTION MATERIAL
1A Casing Cast Iron 40.7 Gasket, Flange Plug Bonded Fibre
2A Impeller Zinc Free Bronze 42.1 Wear Ring, Casing Zinc Free Bronze
3A Backcover Cast Iron 42.2 Wear Ring, Backcover Zinc Free Bronze
10 Bearing Housing Cast Iron 43 Seal, Bearing Cover Felt*
11.1/.2 Bearing Cover Cast Iron 73 Support Foot Steel
20 Shaft Stainless Steel 82.1 Plug, Casing Drain Malleable Iron
21 Impeller Nut Bronze 82.2 Plug, Flange Malleable Iron
25 Slinger Rubber 85 Grease Nipple Steel
28.1 Key, Impeller Key Steel 90.1 Stud, Casing Steel
28.2 Key, Coupling Key Steel 90.2 Stud, Backcover Steel
29 Bearing Steel 90.3 Stud, Gland Steel
30 Gland Cast Iron 92 Setscrew, Bearing Cover Steel
31 Lantern Ring Bush Bronze 93 Setscrew, Support Foot Steel
31A Lantern Ring Cast Iron 94.1 Nut, Casing Stud Steel
32 Shaft Sleeve Stainless Steel 94.2 Nut, Backcover Stud Steel
34 Gland Packing Graphited Fibre 94.3 Nut, Gland Stud Steel
40** Gasket, Casing Bonded Fibre/NBR 97 Washer, Impeller Nut Brass
40.6 Gasket, Drain Plug Bonded Fibre
*Note: Lip Seals fitted to pump models E80-40, E100-40, E125-32, E125-40, E150-32, E150-40, E200-26, E200-32,
E200-40, E250-32, E250-40
**From 1997 O Ring used instead of gasket.
Parts List and Material Identification
Packed Gland Arrangement
7
Elite
Pump Model:Pump Model:
E40-32, E50-32, E65-32, E80-32, E80-40, E100-32,E32-13*, E32-16, E32-20, E32-26, E40-13*, E40-16, E40-20,
E100-40, E125-32, E125-40, E150-20, E150-26, E150-32, E40-26, E50-13, E50-16, E50-20, E50-26, E65-13, E65-16,
E150-40, E200-26, E200-32, E200-40, E250-32, E250-40 E65-20, E65-26, E80-16, E80-20, E80-26, E100-16,
E100-20, E100-26, E125-20, E125-26
Pump Models with clamped back cover:Pump Models with bolted back cover:
E32-13, E32-16, E40-13, E40-16,E32-20, E32-26, E40-20, E40-26, E40-32,
E50-13, E50-16, E65-13, E65-16,E50-20, E50-26, E50-32, E65-20, E65-26,
E80-16, E80-20, E100-16, E100-20, E65-32, E80-26, E80-32, E80-40, E100-26,
E125-20, E150-26, E200-26 E100-32, E100-40, E125-26, E125-32,
E125-40, E150-20, E150-32, E150-40,
E200-32, E200-40, E250-32, E250-40
* no Expeller Vanes
ITEM DESCRIPTION MATERIAL ITEM DESCRIPTION MATERIAL
1A Casing Cast Iron 41 O Ring Seal Plate Nitrile
2A Impeller Zinc Free Bronze 42.1 Wear Ring, Casing Zinc Free Bronze
3A Backcover Cast Iron 42.2 Wear Ring, Backcover Zinc Free Bronze
10 Bearing Housing Cast Iron 43 Seal, Bearing Cover Felt*
11.1/.2 Bearing Cover Cast Iron 73 Support Foot Steel
20 Shaft Stainless Steel 82.1 Plug, Casing Drain Malleable Iron
21 Impeller Nut Bronze 82.2 Plug, Flange Malleable Iron
25 Slinger Rubber 85 Grease Nipple Steel
28.1 Key, Impeller Key Steel 90.1 Stud, Casing Steel
28.2 Key, Coupling Key Steel 90.2 Stud, Backcover Steel
29 Bearing Steel 90.3 Stud, Gland Steel
35 Mechanical Seal Carbon/Ceramic 92 Setscrew, Bearing Cover Steel
36 Spring Sleeve Stainless Steel 93 Setscrew, Support Foot Steel
37 Seal Plate Cast Iron 94.1 Nut, Casing Stud Steel
40** Gasket, Casing Bonded Fibre/NBR 94.2 Nut, Backcover Stud Steel
40.6 Gasket, Drain Plug Bonded Fibre 94.3 Nut, Gland Stud Steel
40.7 Gasket, Flange Plug Bonded Fibre 97 Washer, Impeller Nut Brass
*Note: Lip Seals fitted to pump models E80-40, E100-40, E125-32, E125-40, E150-32, E150-40, E200-26, E200-32,
E200-40, E250-32, E250-40
**From 1997 O Ring used instead of gasket.
Parts List and Material Identification
Mechanical Seal Arrangement
8
Elite
FLANGES

DRILLED
TO

AS/NZS

4331
.
2
(ISO

7005
.
2
-
16b
ar
)
PUMP SHAFT SUCT.DISCH.SPACER COUPLING NET
SIZE MODULE KEY WEIGHT
a f h
1
h
2
b m
1
m
2
n
1
n
2
n
3
h
3
s
1
s
2
w p y d l [kg]
E32-13 25 50 32 80 360 112 140 50 100 70 190 140 100 14 14 14 267 80 100 24 50 8x7 27
E32-16 25 50 32 80 360 132 160 50 100 70 240 190 100 14 14 14 267 80 100 24 50 8x7 35
E32-20 25 50 32 80 360 160 180 50 100 70 240 190 110 14 14 14 267 80 100 24 50 8x7 41
E32-26 25 50 32 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 59
E40-13 25 65 40 80 360 112 140 50 100 70 210 160 100 14 14 14 267 80 100 24 50 8x7 30
E40-16 25 65 40 80 360 132 160 50 100 70 240 190 100 14 14 14 267 80 100 24 50 8x7 36
E40-20 25 65 40 100 360 160 180 50 100 70 265 212 110 14 14 14 267 100 100 24 50 8x7 44
E40-26 25 65 40 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 61
E40-32 35 65 40 125 470 200 225 65 130 95 345 280 110 14 14 14 342 125 140 32 80 10x8 96
EH40-32 35 65 40 125 470 200 225 65 130 95 345 280 110 14 14 14 342 125 140 32 80 10x8 96
E50-13 25 65 50 100 360 132 160 50 100 70 240 190 100 14 14 14 267 100 100 24 50 8x7 34
E50-16 25 65 50 100 360 160 180 50 100 70 265 212 110 14 14 14 267 100 100 24 50 8x7 38
E50-20 25 65 50 100 360 160 200 50 100 70 265 212 110 14 14 14 267 100 100 24 50 8x7 46
E50-26 25 65 50 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 63
E50-32 35 65 50 125 470 225 280 65 125 95 345 280 110 16 14 14 342 124 140 32 80 10x8 101
EH50-32 35 65 50 125 470 225 280 65 125 95 345 280 110 16 14 14 342 124 140 32 80 10x8 101
E65-13 25 80 65 100 360 160 180 65 125 95 280 212 110 14 14 14 267 100 100 24 50 8x7 39
E65-16 25 80 65 100 360 160 200 65 125 95 280 212 110 14 14 14 267 100 100 24 50 8x7 43
E65-20 25 80 65 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 70
E65-26 35 80 65 100 470 200 250 80 160 120 360 280 110 16 18 14 342 100 140 32 80 10x8 81
E65-32 35 80 65 125 470 225 280 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 110
EH65-32 35 80 65 125 470 225 280 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 110
E80-16 25 100 80 125 360 180 225 65 125 95 320 250 110 14 14 14 267 125 100 24 50 8x7 54
E80-20 35 100 80 125 470 180 250 65 125 95 345 280 110 14 14 14 342 125 140 32 80 10x8 70
E80-26 35 100 80 125 470 200 280 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 91
E80-32 35 100 80 125 470 250 315 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 120
EH80-32 35 100 80 125 470 250 315 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 120
E80-40 45 100 80 125 532 280 365 85 160 120 440 340 110 19 18 14 368 132 140 42 110 12x8 161
E100-16 35 125 100 125 470 200 280 30 160 120 340 260 110 16 18 14 342 125 140 32 80 10x8 71
E100-20 35 125 100 125 470 200 280 80 160 120 360 280 110 16 18 14 342 125 140 32 80 10x8 85
E100-26 35 125 100 140 470 225 280 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 106
E100-32 35 125 100 140 470 250 315 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 134
E100-40 45 125 100 140 530 280 355 100 200 150 500 400 110 18 23 14 370 140 140 42 110 12x8 174
E125-20 35 150 125 140 470 250 315 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 106
E125-26 35 150 125 140 470 250 355 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 115
E125-32 45 150 125 140 530 280 355 100 200 150 500 400 110 18 23 14 370 140 140 42 110 12x8 163
E125-40 45 150 125 140 530 315 400 100 200 150 500 400 110 18 23 14 370 140 140 42 110 12x8 181
E150-20 35G 200 150 160 495 280 400 100 200 150 550 450 110 20 23 14 367 160 140 32 80 10x8 156
E150-26 45 200 150 160 530 250 355 100 200 150 450 350 110 18 23 14 370 160 140 42 110 10x8 148
E150-32 45 200 150 160 530 280 400 100 200 150 550 450 110 18 23 14 370 160 140 42 110 12x8 170
E150-40 45 200 150 160 530 315 450 100 200 150 550 450 110 18 23 14 370 160 140 42 110 12x8 209
E200-26 45D 250 200 180 553 315 450 100 200 150 550 450 110 20 28 14 393 180 180 42 110 12x8 206
E200-32 55 250 200 180 670 315 480 120 220 170 600 480 110 20 28 14 504 180 180 48 110 14x9 251
E200-40 55 250 200 180 670 335 480 120 220 170 600 480 110 20 28 14 504 180 180 48 110 14x9 295
E250-32 55 300 250 220 691 355 520 150 250 200 660 510 110 22 28 14 525 220 180 48 110 14x9 311
E250-40 55 300 250 220 682 400 560 150 250 200 660 510 110 22 28 14 516 220 180 48 110 14x9 390
Dimensions shown in mm
END
END ELEVATION SIDE ELEVATION
SHAFTPUMP FOOT
Dimensions
SUCTION
DISCHARGE
ROTATION
9
Elite
Branch
Size D b d
1
f d
2
k
32 140 18 78 2 18 100
40 150 18 88 3 18 110
50 165 20 102 3 18 125
65 185 20 122 3 18 145
80 200 22 138 3 18 160
100 220 24 158 3 18 180
125 250 26 188 3 18 210
150 285 26 212 3 22 240
200 340 32 268 3 22 295
250 405 32 320 3 26 355
300 460 32 378 4 26 410
Flange dimensions and drilling according to AS/NZS 4331.2, ISO 7005.2 - 16 bar
(BS4504 - 1969 Table 16/11, DIN 2533 PN16)
Dimensions shown in mm
*Holes - Equally spaced straddling pump centreline
Shaft Key Key Key Seat
Module Tol Length Height Width Depth
-0.004
+0.009
-0.002
+0.018
-0.002
+0.018
-0.002
+0.018
PUMP A B* D S PUMP A B* S
MODEL CASING HOUSING GAUGE GAUGE MODEL CASING HOUSING GAUGE
DRAIN DRAIN TAPPING TAPPING DRAIN DRAIN TAPPING
E32-13 1/4 3/8 1/4 1/4 E80-26 3/8 3/8 1/4
E32-16 1/4 3/8 1/4 1/4 E80-32 3/8 3/8 3/8
E32-20 1/4 3/8 1/4 1/4 EH80-32 3/8 3/8 3/8
E32-26 3/8 3/8 1/4 1/4 E80-40 3/8 3/8 3/8
E40-13 1/4 3/8 1/4 1/4 E100-16 3/8 3/8 3/8
E40-16 1/4 3/8 1/4 1/4 E100-20 3/8 3/8 3/8
E40-20 1/4 3/8 1/4 1/4 E100-26 3/8 3/8 3/8
E40-26 3/8 3/8 1/4 1/4 E100-32 3/8 3/8 3/8
E40-32 3/8 3/8 1/4 1/4 E100-40 3/8 3/8 3/8
EH40-32 3/8 3/8 1/4 1/4 E125-20 3/8 3/8 3/8
E50-13 1/4 3/8 1/4 1/4 E125-26 3/8 3/8 3/8
E50-16 3/8 3/8 1/4 1/4 E125-32 3/8 3/8 3/8
E50-20 1/4 3/8 1/4 1/4 E125-40 3/8 3/8 3/8
E50-26 3/8 3/8 1/4 1/4 E150-20 3/8 3/8 3/8
E50-32 3/8 3/8 1/4 1/4 E150-26 3/8 3/8 3/8
EH50-32 3/8 3/8 1/4 1/4 E150-32 3/8 3/8 3/8
E65-13 1/4 3/8 1/4 1/4 E150-40 3/8 3/8 3/8
E65-16 3/8 3/8 1/4 1/4 E200-26 3/8 1/2 3/8
E65-20 3/8 3/8 1/4 1/4 E200-32 3/8 3/8 3/8
E65-26 3/8 3/8 1/4 1/4 E200-32 3/8 3/8 3/8
E65-32 3/8 3/8 1/4 1/4 E200-40 3/8 3/8 3/8
EH65-32 3/8 3/8 1/4 1/4 E250-32 3/8 3/8 3/8
E80-16 3/8 3/8 1/4 1/4 E250-40 3/8 3/8 3/8
E80-20 3/8 3/8 1/4 1/4
Dimensions shown in inch
3/8
3/8
3/8
3/8
3/8
1/4
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/4
1/4
3/8
3/8
1/4
1/4
*Left side view from suction
M16
M16
4
8
4
4
4
1/4
Raised Face
GAUGE
TAPPING
D
Key dimensions are in nominal and expressed in mm
M24
Nom
Flange
M16
M16
M16
M16
M16
Drilling*
Bolting
8
N0.
8
8
12
M20
M24
12 M20
12
Diameter D
55
24
32
42
48
25
35
45
40
50
80
7 20
27
37
42.5
3/8
3/8
8
10
12
14
8
8
9
32
Flange Data
Shaft Dimensions
Service Connections
DISCHARGE
SUCTION
ROTATION
SIDE ELEVATION
KEY WIDTH
KEY HEIGHT
KEY LENGTH
SEAT
DEPTH
END ELEVATION
10
Elite
Module L L
1
L
2
d d
1
d
2
k f g
Size No. rings
25 44 30 56 48 32 24 85 M8 35 8 Sq 3
35 53* 40* 63** 60 40 32 100 M10 40 10 Sq 3*
45 63 46 78 75 54 44 110 M12 50 10 Sq 4
55 80 62 62 90 65 53 130 M12 55 13Sq 4
*: models E40-32, E50-32, E65-32, E80-32, E100-32, E100-32, E125-26 L=63, L
1
=50, No. Rings=4 Dimensions shown in mm
**: model E150-20 L
2
=83
Mechanical Seal, A20 - Conversion Kits
The kit is suitable to convert standard packed gland pumps.
The kit comprises of mechanical seal, spring sleeve, seal plate, O ring seal and nameplate.
Module
E32-13/16/20/26
E40-13/16/20/26
E50-13/16/20/26 25
E65-13/16/20
E80-16
E40-32, EH40-32
E50-32, EH50-32
E65-26/32, EH 65-32
E80-20/26/32, EH80-32
E100-16/20/26/32
E125-20/26
E150-20 35G
E80-40
E100-40
E125-32/40
E150-26/32/40
E200-26
45D
E200-32
E200-40
E250-32 55
E250-40
213594
Mechanical Seal
Spring Sleeve
Seal Plate
Pump Size
Spring Sleeve
Seal Plate
O ring
213591
Conversion Kit No.Parts included in kit
Mechanical Seal 213524
Nameplate
36-25-HF
O ring
Nameplate
Mechanical Seal
21373HA
BS-233-GM
Nameplate 218003
Packing
21361HF (35)
21372HA
213532
21371HA
BS-225-GM
218003
Spring Sleeve
Seal Plate
Spring Sleeve
Seal Plate
O ring
O ring
218003
213553
36-55-HF
21374HA
BS-238-GM
36-45D-HF (45D)
36-35G-HF (35G)
213592G
BS-229-GM
218003
213544
36-45-HF (45)
Nameplate
Mechanical Seal
45 213593
213593D
35 213592
Nominal Stuffing Box Dimensions
NOTE:
Only some models have combination
lantern ring-register bush, check assembly drawing.
From end of stuffing box.
MODULE 45 & 55
MODULE 25 & 35
11
Type Series Booklet
Elite
KSB Australia Pty Ltd
ABN: 29 006 414 642
Victorian Head Office New South Wales Queensland South Australia Western Australia New Zealand
27 Indwe St,Unit 1, 28 Skinner Ave,53 Jijaws St,Unit 4, 348 Richmond Rd,Unit 2, 86 Catalano Circuit,Unit 2, 5 Civil Place,
Tottenham, 3012 Riverwood, 2210 Sumner Park, 4074 Netley, 5037 Canning Vale, 6155 Albany, Auckland 1331
Tel: +61 (03) 9314 0611 Tel: +61 (02) 9584 2099 Tel: +61 (07) 3725 8200 Tel: +61 (08) 8234 0066 Tel: +61 (08) 9455 7900 Tel: +64 (09) 476 4047
Fax: +61 (03) 9314 7435 Fax: +61 (02) 9584 2111 Fax: +61 (07) 3725 8299 Fax: +61 (08) 8443 5411 Fax: +61 (08) 9455 7800 Fax: +64 (09) 476 4048
ksbvicsales@ksbajax.com.au ksbnswsales@ksbajax.com.au ksbqldsales@ksbajax.com.au ksbsasales@ksbajax.com.au ksbwasales@ksbajax.com.au pumps@ksbajax.co.nz
WEBSITE: www.ksbajax.com.au 24 HOUR EMERGENCY SERVICE LINE: 1300 301 356
Due to our policy of constant research and development, product specification may change without notice Publication 2007 02/14 1/2K AGP