Standards - Lee's Compliance

pigsabusiveΗλεκτρονική - Συσκευές

29 Νοε 2013 (πριν από 4 χρόνια και 5 μήνες)

246 εμφανίσεις






NOVEMBER
2013


Dear Subscriber

Please take note of the following amendments

which have been made

to

our COMPULSORY
Standards issued by our Department Of Trade And
Industry over OCTOBER


NOVEMBER

2013

Alison Lee



STANDARDS


No. 782 18 October
2013

(Government Gazette 36923)

STANDARDS ACT, 2008

STANDARDS MATTERS

In terms of the Standards Act, 2008 (Act No. 8 of 2008), the Council of the South African Bureau of Standards has acted in re
gard to standards in
the manner set out in the Schedules to
this notice.

All South African standards that were previously published by the South African Bureau of Standards with the prefix "SABS" ha
ve been redesignated
as South African national standards and are now published by the SABS Standards Division (a divis
ion of SABS) with the prefix "SANS".

A list of all existing South African national standards was published by Government Notice No. 1373 of 8 November 2002.

In the list of SANS standards below, the equivalent SABS numbers, where applicable, are given below

the new SANS numbers for the sake of
convenience. Standards that were published with the "SABS" prefix are listed as such.






SCHEDULE 1: ISSUE OF NEW STANDARDS

The standards mentioned have been issued in terms of section 16(3) of the Act.




Standard No.
and year

Title, scope and purport

SANS 689:2013

Automatic rail
-
weighbridges.

Specifies requirements and test methods for automatic
rail
-
weighbridges (ARWs
) used to determine the mass of railway wagons when they are
in motion, as well as requirements for integral control instruments for the partial static
weighing of reference wagons. Also provides standardized requirements and testing
procedures to evaluate

the metrological and technical characteristics of an ARW in a
uniform and traceable way.

SANS
3457:2013/ ISO
3457:2003

Earth
-
moving machinery

-

Guards

-

Definitions and ISO requirements.

Defines principal
terms and specifies requirements for, and charact
eristics of, guards and other means of
protecting personnel from mechanical, fluid or thermal hazards associated with the
operation and routine maintenance of earthmoving machinery as defined in ISO 6165
(published in South Africa as an identical adoption
under the designation SANS 261),
when used as intended by the manufacturer.

SANS 4378
-
4:2013/ ISO
4378
-
4:2009

Plain bearings
-

Terms, definitions, classification and symbols

-

Part 4: Basic
symbols.

Defines basic symbols for use in the field of plain bear
ings. Additional signs
are also defined for use as superscripts and subscripts. This classification is
established for use in calculations and technological and geometrical determinations,
as well as in the quality assurance of plain bearings.

SANS 11770
-
5:2013/ ISO/IEC
11770
-
5:2011

Information technology

-

Security techniques

-

Key management
-

Part 5: Group key
management.

Specifies key establishment mechanisms for multiple entities to provide
procedures for handling cryptographic keying material used in

symmetric or asymmetric
cryptographic algorithms in accordance with the security policy in force.

SANS 12651
-
1:2013/ ISO
12651
-
1

Electronic document management
-

Vocabulary
-

Part I: Electronic document
imaging.

Facilitate communication in the field of
electronic document management and
translation of the terms it contains into other languages.

SANS
13766:2013/ ISO
13766:2006

Earth
-
moving machinery
-

Electromagnetic compatibility.

Provides test methods and
acceptance criteria for the evaluation of the
electromagnetic compatibility of earth
-
moving machinery as defined in ISO 6165 (published in South Africa as an identical
adoption under the designation SANS 261).

SANS 20492
-
3:2013/ ISO
20492
-
3:2010

Glass in buildings
-

Insulating glass units
-

Part 3: G
as concentration and gas
leakage.

Specifies two methods of test for insulating glass units, including a
determination of the gas leakage rate and a determination of gas concentration
tolerances. The two methods designated as approach 1, which is intended f
or use in
markets such as North America, and approach 2, which is intended for use in markets
such as Europe.

SANS 20492
-
4:2013/ ISO
20492
-
4:2010

Glass in buildings
-

Insulating glass units

-

Part 4: Method of test for the physical
attribute of edge seals
.

Specifies methods for testing the edge seal strength, and
partially testing the moisture and gas permeation through sealants, of glass insulating
units.

SANS
24745:2013/
ISO/IEC
24745:2011

Information technology

-

Security techniques
-

Biometric informa
tion
protection.

Provides guidance for the protection of biometric information under various
requirements for confidentiality, integrity and renewability/revocability during storage
and transfer. Also provides requirements and guidelines for the secure and

privacy
-
compliant management and processing of biometric information.

SANS
27007:2013/
ISO/IEC
27007:2011

Information technology
-

Security techniques
-

Guidelines for information security
management systems auditing.

Provides guidance on managing an inf
ormation security
management system (ISMS) audit programme, on conducting the audits, and on the
competence of ISMS auditors.

SANS
27010:2013/
ISO/IEC
27010:2012

Information technology
-

Security techniques
-

Information security management for
inter
-
sector and inter
-

organizational communications.

Provides guidelines in addition to
guidance given in the ISO/IEC 27000 family of standards for implementing information
security management within information sharing communities. Provides controls and

guidance specifically relating to initiating, implementing, maintaining, and improving
information security in inter
-
organization and inter
-
sector communications.





SANS 27034
-
1:2013/

Information technology
-

Security techniques

-

Application security
-

Part 1: Overview
and concepts.

Provides

ISO/IEC 27034
-
1:2011

guidance to assist organizations in integrating security into the processes used for
managing their applications. Presents an overview of application security.

SANS
27035:2013/

Information
technology
-

Security techniques

-

Information security incident
management.

Provides a structured and

ISO/IEC
27035:2011

planned

approach to detect, report and assess information security incidents, respond
to and manage information security incidents, detect, assess and manage information
security vulnerabilities, and continuously improve information security and incident
manageme
nt as a result of managing information security incidents and vulnerabilities.

SANS 28560
-
1:2013/

Information and documentation
-

RFID in libraries
-

Part 1: Data elements and general
guidelines for implementation.

ISO 28560
-
1:2011

Specifies a model for
the use of radio frequency identification (RFID) tags for items
appropriate for the needs of all types of libraries, including academic, public, corporate,
special and school.

SANS 28560
-
3:2013/

Information and documentation
-

RFID in libraries
-

Part 3:
Fixed length
encoding.

Provides a data model and

ISO 28560
-
3:2011

encoding rules for the use of radio frequency identification (RFID) tags for items
appropriate for the needs of all types of libraries (including academic, public, corporate,
special and sc
hool libraries). Specifies the rules for encoding a subset of data elements
taken from the total set of data elements listed in ISO 28560
-
1 (published in South
Africa as an identical adoption under the designation SANS 28560
-
1) into a basic block
and other

data elements into extension blocks onto the RFID tag.

SANS
29128:2013/

Information technology
-

Security techniques
-

Verification of cryptographic
protocols.

Establishes a technical base for

ISO/IEC
29128:2011

the security proof of the specification o
f cryptographic protocols. Specifies design
evaluation criteria for these protocols, as well as methods to be applied in a verification
process for such protocols.

SANS
29150:2013/

Information technology
-

Security techniques

-

Signcryption.

Specifies fou
r mechanisms
for signcryption that employ

ISO/IEC
29150:2011

public key cryptographic techniques requiring both the originator and the recipient of
protected data to have their own public and private key pairs.

SANS 29192
-
2:2013/

Information technology
-

Security techniques
-

Lightweight crytography

-

Part 2: Block
ciphers.

Specifies two block

ISO/IEC 29192
-
2:2011

ciphers suitable for applications that require lightweight cryptographic implementations,
namely PRESENT: a lightweigh
t block cipher with a block size of 64 bits and a key size
of 80 or 128 bits, and CLEFIA: a lightweight block cipher with a block size of 128 bits
and a key size of 128, 192 or 256 bits.

SANS
30300:2013/

Information and documentation
-

Management systems
for records
-

Fundamentals and
vocabulary.

Defines terms and

ISO 30300:2011

definitions applicable to the standards on MSR prepared by ISO/TC 46/SC 11.
Establishes the objectives for using a MSR, provides principles for a MSR, describes a
process approach

and specifies roles for top management.

SANS
30301:2013/

Information and documentation
-

Management systems for records
-

Requirements.

Specifies requirements to be met

ISO 30301:2011

by a MSR

in order to support an organization in the achievement of its mandate,
mission, strategy and goals. It addresses the development and implementation of a
records policy and objectives and gives information on measuring and monitoring
performance.

SANS 600
79
-
33:2013/ IEC
60079
-
33:2012

Explosive atmospheres
-

Part 33: Equipment protection by special protection "s".

Gives
the specific methodology for the assessment and testing, and requirements for marking
of electrical equipment, parts of electrical equipmen
t and Ex components with special
protection "s".

SANS 61968
-
11:2013/ IEC
61968
-
11:2013

Application integration at electric utilities
-

System interfaces for distribution
management
-

Part 11: Common information model (CIM) extensions for
distribution.

Spe
cifies the distribution extensions of the Common Information Model
(CIM). Covers the information model that extends the base CIM for the needs of
distribution networks, as well as for integration with enterprise
-
wide information systems
typically used with
in electrical utilities.

SANS 62271
-
37
-
082:2013/

High
-
voltage switchgear and controlgear
-

Part 37
-
082: Standard practice for the
measurement of sound pressure

IEC/IEEE 62271
-
37
-
082:2012

levels on alternating current circuit
-
breakers.

Provides methods for the measurement of
sound pressure levels produced by outdoor alternating current circuit
-
breakers in a


free
-
field environment.

SANS
62560:2013/ IEC
62560:2011

Self
-
ballasted LED
-
lamps for general lighting services by voltage > 50 V
-

Safety
specification.

Specifies the safety and interchangeability requirements, together with the
test methods and conditions required to show compliance of LED
-
lamps with integrated
means for stable operation (self
-
ballasted LED
-
lamps), intended for domes
tic and
similar general lighting purposes, having a rated wattage up to 60 W, a rated voltage of
> 50 V up to 250 V and caps as specified.

SANS 80079
-
34:2013/ IEC
80079
-
34:2011

Explosive atmospheres
-

Part 34: Application of quality systems for equipment
manufacture.

Specifies particular requirements and information for establishing and
maintaining a quality system to manufacture Ex equipment including protective systems
in accordance with the Ex certificate. It does not preclude the use of other quality
s
ystems that are compatible with the objectives of ISO 9001 (published in South Africa
as an identical adoption under the designation SANS 9001) and provide equivalent
results.

SATS
62504:2013/

General lighting
-

LEDs and LED modules
-

Terms and definition
s.
Presents terms and
definitions relevant for lighting

IEC/TS
62504:2011

with LED light sources.






SCHEDULE 2: AMENDMENT OF EXISTING STANDARDS

The standards mentioned have been amended in terms of section 16(3) of the Act. The number and date of a
standard that has been superseded
appear in brackets below the new number. In the case of an amendment issued in consolidated format, the edition number of the

new (consolidated)
edition appears in brackets below the number of the standard.





Standard No. and
year

Title, scope and purport

SANS 193:2013 (Ed.
2.2)

Fire dampers. Consolidated edition incorporating amendment No. 2.
Amended to
update referenced standards.

SANS 261:2013/
ISO 6165:2012
(SANS 261:2008)

Earth
-
moving machinery
-

Basic
types
-

Identification and terms and
definitions.

Gives terms and definitions and an identification structure for classifying
earth
-
moving machinery designed to perform excavation, loading, transportation,
and drilling, spreading, compacting or trenching o
f earth, rock, and other materials,
during work, for example, on roads and dams, in quarries and mines, and on
building sites. Purpose is to provide a clear means of identifying machines
according to their function and design configurations.

SANS 457
-
3:20
13
(SABS 457
-
3:2000)

Wooden poles, droppers, guardrail posts and spacer blocks
-

Part 3: Hardwood
species.

This part of SANS 457 specifies requirements for preservative
-
treated
hardwood structural poles, agricultural poles, fencing poles, round droppers,
g
uardrail posts and spacer blocks. The poles are intended for the erection of fences
and vine trellises, for general use in orchards and for structural purposes. The
droppers are intended for fencing. The posts and spacer blocks are intended for the
erectio
n of steel guardrails at the sides of roads.

SANS 475:2013 (Ed.
1.2)

Luminaires for interior lighting, streetlighting and floodlighting
-

Performance
requirements. Consolidated edition incorporating amendment No. 2.

Amended to
update referenced standards
and to correct the power factor for lamps smaller than
or equal to 25 Watts.

SANS 517:2013 (Ed.
1.2)

Light steel frame building. Consolidated edition incorporating amendment No.
2.

Amended to update referenced standards, to correct the map on geographic
regions related to wind speeds, to update requirements in the tables on external
pressure coefficient cpe for mono
-
pitched roofs and duo
-
pitched roofs, to update
requirements for wall

elements, and to correct the map on climate zones in South
Africa.

SANS 673:2013 (Ed.
3.3)

Mixtures of copper
-
chromium
-
arsenic compounds for timber preservation.
Consolidated edition incorporating amendment No. 3.
Amended to include the X
-
ray
fluorescence

(XRF) and the inductively coupled plasma emission (ICP)
spectrometric methods of analyses and to renumber accordingly, to amend the
requirements with respect to the gooch crucible that is used in the wet tritation
methods of arsenic content elemental conc
entration.

SANS 1017:2013
(Ed. 1.5)

Electric cables for motor vehicles
-

Low
-
voltage cables and flexible earthing straps
for motor vehicles. Consolidated edition incorporating amendment No. 5.

Amended
to update referenced standards.

SANS 1083:2013
(Ed. 2
.3)

Aggregates from natural sources
-

Aggregates for concrete. Consolidated edition
incorporating amendment No. 3.

Amended to modify the introduction, update
referenced standards, to modify the definitions of "aggregate", "coarse aggregate"
and "fine aggre
gate", change the sieve grading sizes and modify the requirements
for coarse aggregate for use in concrete.

SANS 1186
-
3:2013
(Ed. 1.3)

Symbolic safety signs
-

Part 3: Internally illuminated signs. Consolidated edition
incorporating amendment No. 3.

Amende
d to replace reference to SANS 7253 with
SANS 9227.

SANS 1236:2013
(Ed. 1.2)

Silvered glass mirrors for general use. Consolidated edition incorporating
amendment No. 2.

Amended to update referenced standards.

SANS 1263
-
3:2013/
(Ed. 1.3)

Safety and security glazing materials for buildings
-

Part 3: Bullet
-
resistant glazing
materials. Consolidated edition incorporating amendment No. 3.

Amended to
correct cross
-
references to referenced standards, to modify the requirements for
classification

of glazing material, calibre of firearm, ammunition and range in the
table on levels of simulated ballistic attack, and to replace the apparatus "velocity
measurement system" (and its explanatory footnote) with "ballistic chronograph".

SANS 1422:2013
(Ed
. 2.1)

Domestic electric laundry treatment machines. Consolidated edition incorporating
amendment No. 1.

Amended to move reference to legislation to the foreword.

SANS 1547:2013
(Ed. 1.6)

Traffic signal controllers. Consolidated edition incorporating

amendment No.
6.

Amended to change electrical requirements for controlgear, and to update


referenced standards.

SANS 1679:2013
(Ed. 2.1)

Pasteurized milk. Consolidated edition incorporating amendment No. 1.

Amended
to update legislation and the reference
d standards.

SANS 1814:2013
(Ed. 1.3)

D.C. supplied luminaires for fluorescent lamps. Consolidated edition incorporating
amendment No. 3.

Amended to update referenced standards. Can only be used in
conjunction with SANS 60925, SANS 60598
-
1 and SANS
61347
-
2
-
3.

SANS 1816:2013
(SANS 1816:2005)

Electricity supply
-

Quality of supply: Power quality monitoring instruments
specification.

Specifies product requirements for instruments, the functions of which
include measuring and monitoring of power quality

parameters in a.c. power
systems. Can be used in, for example, the generation, transmission and distribution
of electricity and related telecommunication systems, e.g. inside a power station or
a substation, or a distributed generator connection, or at th
e interface point between
the installation and the network, e.g. in order to check the compliance to the
connection agreement with a network operator. Can only be used in conjunction
with SANS 61000
-
4
-
30.

SANS 1865:2013
(Ed. 1.2)

Point
-
of
-
use drinking wat
er treatment units. Consolidated edition incorporating
amendment No. 2.

Amended to update a referenced standard.

SANS 6152:2013
(Ed. 2.1)

Available alkali content of cement extenders (complying with SANS 50197
-
1).
Consolidated edition incorporating amendm
ent No. 1.
Amended to update
referenced standards.

SANS 6210:2013
(Ed. 3.1)

Domestic solar water heaters
-

Mechanical qualification tests. Consolidated edition
incorporating amendment No. 1.

Amended to update referenced standards.

SANS 9297:2013
(Ed. 1.2)

Water quality
-

Determination of chloride
-

Silver nitrate titration with chromate
indicator (Mohr's method). Consolidated edition incorporating amendment No.
2.

Amended to update referenced standards.

SANS 10083:2013
(Ed. 5.2)

The measurement and assess
ment of occupational noise for hearing conservation
purposes. Consolidated edition incorporating amendment No. 2.

Amended to
change requirements for baseline audiometry, and to change the title and text of the
table on frequency of contributions to the PLH

(table 1).

SANS 10204:2013
(Ed. 2.2)

The application of fumigants. Consolidated edition incorporating amendment No.
2.

Amended to move a reference to legislation to the foreword.

SANS 10292:2013
(SABS 0292:2001)

Earthing of low
-
voltage (LV) distribution

systems.

Gives requirements and
recommendations for the provision of a safe electricity supply to the consumer.
Establishes general principles for the earthing of low
-
voltage distribution systems of
which the supply starts at the point of generation or tr
ansformation and ends at the
supply earth terminal of the consumer. Applies to a distributor that operates at a
voltage (a.c. or d.c.) that does not exceed 1 000 V.

SANS 10590:2013/
ISO 10590:2005
(SABS ISO
10590:1991)

Building construction

-

Sealants
-

D
etermination of tensile properties of sealants at
maintained extension after immersion in water.
Specifies a method for the
determination of the influence of water immersion on the adhesion/cohesion
properties at maintained extension of sealants used in joi
nts in building
construction.

SANS 15801:2013/

Document management
-

Information stored electronically
-

Recommendations for
trustworthiness and reliability.

ISO/TR 15801:2009
(SANS 15801:2005)

Describes the implementation and operation of document
management systems
that can be considered to store electronic information in a trustworthy and reliable
manner.

SANS 18000
-
3:2013/ ISO/IEC
18000
-
3:2010
(SANS 18000
-
3:2009)

Information technology
-

Radio frequency identification for item management
-

Part
3: Parameters for air interface communications at 13,56 MHz.

Provides physical
layer, collision management system and protocol values for RFID systems for item
identification operating at 13,56 MHz in accordance with the requirements of
ISO/IEC 18000
-
1 (pu
blished in South Africa as an identical adoption under the
designation SANS 18000
-
1).

SANS 18000
-
6:2013/ ISO/IEC
18000
-
6:2013
(SANS 18000
-
6:2012)

Information technology

-

Radio frequency identification for item management

-

Part
6: Parameters for air inte
rface communications at 860 MHz to 960 MHz
General.

Defines the air interface for radio frequency identification (RFID) devices
operating in the 860 MHz to 960 MHz industrial, scientific, and medical (ISM) band
used in item management applications.

SANS 1
9110:2005/
ISO 19110:2005

Geographic information
-

Methodology for feature cataloguing. ISO amendment No.
1.

Amended to change the scope and the clause on conformance, to update
referenced standards and terms and definitions, to change the clauses on
abbre
viations and principal requirements and the annexes on abstract test suite,
feature catalogue template, feature cataloguing examples, and feature cataloguing


concepts, and to insert three new annexes on encoding description, management
of feature catalogue

registers, and XML implementation example.

SANS 19131:2012/
ISO 19131:2007

Geographic information
-

Data product specifications. ISO amendment No.
1.

Amended to include requirements relating to the inclusion of an application
schema and feature catalogue and the treatment of coverages in an application
schema.

SANS 20011:1981/
ECE R11:1981

Uniform provisions concerning the approval of vehicles with reg
ard to door latches
and door retention components. ECE amendment No. 2.
Amended to change the
scope, to add definitions, to change the clauses on approval, specifications, tests
and modification of the vehicle type, to insert a new clause on transitional pr
ovision,
to change the annexes on arrangements of approval marks, latch test for load tests
one, two, and three and force application, to add a new clause on inertial test
procedures, hinge test procedure and sliding side door.

ECE amendment No.
3.

Amended

to change requirements for tests on load test three, door hinges, door
system, and door locks, to change requirements for test in the annexes on test
procedure for door latches and door retention components, inertial test procedures,
hinge test procedure,

and sliding side door.

ECE amendment No. 4.
Amended to
change requirements for tests on load test three, door hinges, and door system, to
change requirements for tests in the annexes on test procedure for door latches
and door retention components, inertia
l test procedures, hinge test procedure, and
sliding side door.

SANS 20014:2006/
ECE R14:2006

Uniform provisions concerning the approval of vehicles with regard to safety
-
belt
anchorages, isofix anchorages systems and isofix top tether anchorages. ECE
ame
ndment No. 3.

Amended to change the scope.

ECE amendment No.
4.

Amended to delete a definition, to change requirements for approval, and
specifications, to add requirements in the clause on transitional provisions, and to
change requirements in the annex o
n arrangements of the approval mark.
ECE
amendment No. 5.

Amended to change a clause on the minimum number of belt
anchorages to be provided, and to change the requirements of vehicle in categories
M, N, and M1 in the subclause on minimum number of belt anc
horages to be
provided.

ECE amendment No. 6.

Amended to change the design of the ISOFIX
anchorages in the subclause on general specifications.

ECE corrigendum No.
2.

Corrected to change a definition, and to change the requirements of ISOFIX
anchorages in t
he subclause on general specifications.

SANS 20017:2004/
ECE R17:2002

Uniform provisions concerning the approval of vehicles with regard to the seats,
their anchorages and any head restraints. ECE amendment No. 1.

Amended to
change the scope, to change th
e clause on requirement and tests, to add a new
clause in the annex on communication, to correct the word "decelerometers" to read
"accelerometers" in the annex on results, to change the requirements for test in the
annexes on test of resistance to inertia

effects, and dynamic testing of seat
-
backs
and partitioning systems used as luggage restraint systems, and to change the
heading of the graph in the annex on corridor of sled's deceleration or acceleration
as a function of time.

ECE amendment No. 2.

Amend
ed to change the scope, to
add new definitions, to change a subclause in the clause on approval, to add new
clauses on requirements, to change subclauses in the clause on requirements, to
add new clauses on transitional provisions, and to change the annex
on
arrangement of approval marks.

ECE amendment No. 3.

Amended to change a
definition, and to change and to delete subclauses in the clause on requirements.

SANS 60311:2013/
IEC 60311:2009
(Ed. 3.2)

Electric irons for household or similar use
-

Methods for measuring performance.
Consolidated edition incorporating amendment No. 2.
Amended to update the
definition of the auto switch
-
off device, to update the measurement of heating
-
up
time for steaming op
eration, the measurement of steaming time, steaming rate and
water leakage rate, the determination of total steaming time for hard water, and
figure 4 (test apparatus).

SANS 60335
-
2
-
27:2013/ IEC 60335
-
2
-
27:2012 (Ed. 4.1)

Household and similar electrical
appliances

-

Safety
-

Part 2
-
27: Particular
requirements for appliances for skin exposure to ultraviolet and infrared radiation.
Consolidated edition incorporating amendment No. 1.

Amended to change the
heading of the definitions clause to read "Terms and
definitions", to give clarification
of radiation measurement procedure and guidelines for an exposure time schedule,
to include a normative annex on software evaluation, and to delete a referenced
standard from the bibliography. Can only be used in conjunc
tion with SANS 60335
-
1.

SANS 60432
-
1:2013/ IEC 60432
-
Incandescent lamps
-

Safety specifications

-

Part 1: Tungsten filament lamps for
domestic and similar general lighting purposes. Consolidated edition incorporating


1:2012 (Ed. 1.2)

amendment No. 2.

Amen
ded to include requirements for K.6 protection from water
contact and K.7 photobiological safety.

SANS 60901:2008/
IEC 60901:2008

Single
-
capped fluorescent lamps
-

Performance specifications. IEC amendment No.
5.

Amended to replace data sheets, and to upd
ate the annexes on method of test
for electrical, photometric and cathode characteristics, method of test for lumen
maintenance and life, and information for ballast and starter design.

SANS 61347
-
1:2013/ IEC 61347
-
1:2012 (Ed. 2.2)

Lamp controlgear
-

Part

1: General and safety requirements. Consolidated edition
incorporating amendment No. 2.

Amended to add an introduction (to amendment
2), to update the scope, normative references, terms and definitions, general
requirements, notes on tests, marking, earth
ing, protection against accidental
contact with live parts, moisture resistance and insulation, electric strength, thermal
endurance test for windings of ballasts, fault conditions, construction, creepage
distances and clearances, no
-
load output voltage, t
o update an annex for test to
establish whether a conductive part is a live part which may cause an electric shock
and an annex for thermally protected lamp controlgear, to include an annex for
particular additional requirements for controlgears providing
SELV, an annex for
dielectric strength test voltages for controlgear intended for the use in impulse
withstand category III, an annex for requirements for insulation materials used for
double or reinforced insulation, an annex for additional requirements f
or built
-
in
electronic controlgear with double or reinforced insulation, and to update the
bibliography.

SANS 61347
-
2
-
9:2013/ IEC 61347
-
2
-
9:2012 (SANS
61347
-
2
-
9:2010)

Lamp controlgear
-

Part 2
-
9: Particular requirements for electromagnetic
controlgear for

discharge lamps (excluding fluorescent lamps).

Specifies particular
safety requirements for electromagnetic controlgear for discharge lamps such as
high
-
pressure mercury vapour, low
-
pressure sodium vapour, high
-
pressure sodium
vapour and metal halide lamp
s.

SANS 62035:2013/
IEC 62035:2012
(Ed. 1.2)

Discharge lamps (excluding fluorescent lamps)
-

Safety specifications. Consolidated
edition incorporating amendment No. 2.
Amended

to add a new paragraph and a
NOTE on UV radiation, change a requirement for test procedures and conditions of
compliance for containment, and include annex I (containment testing procedure for
metal halide lamps with quartz arc tubes) and annex J (contain
ment testing
procedure for metal halide lamps with ceramic arc tubes).






SCHEDULE 3: CANCELLATION OF STANDARDS

In terms of section 16(3) of the Act the following standards have been cancelled.




Standard No. and
year

Title

SANS 1561
-
1:2006

Rewound and

refurbished rotating electrical machines
-

Part 1: Low
-
voltage three
-
phase induction motors.

SCHEDULE 4: ADDRESSES OF SABS OFFICES

The addresses of offices of the South African Bureau of Standards where copies of standards mentioned in this notice can be

obtained, are as
follows:

1.

The CEO, South African Bureau of Standards, 1 Dr Lategan Road, Groenkloof, Private Bag X191, Pretoria 0001.

2.

The Manager, Western Cape Regional Office, SABS, Liesbeek Park Way, Rosebank, PO Box 615, Rondebosch 7701.

3.

The
Manager, Eastern Cape Regional Office, SABS, 30 Kipling Road, cor. Diaz and Kipling Roads, Port Elizabeth, PO Box 3013, North

End
6056.

4.

The Manager, KwaZulu
-
Natal Regional Office, SABS, 15 Garth Road, Waterval Park, Durban, PO Box 30087, Mayville 4058.

5.

The Control Officer, Bloemfontein Branch Office, SABS, 34 Victoria Road, Willows, Bloemfontein, PO Box 20265, Willows 9320.