How to Change over from sky - Sky User

painveilΔίκτυα και Επικοινωνίες

24 Οκτ 2013 (πριν από 3 χρόνια και 9 μήνες)

214 εμφανίσεις

How to Chang
e

over from sky’ s firmware to Sagem’ s Generic and how to get your username and password.

By Anarchyuk

Disclaimer
:

whatever

you do to your
router

is at your own risk! This
will void the warranty. Skys terms
state you are not to use another route
r etc bla

bla fook sky..

Reason: loads more settings and it solved my slow wireless speeds.


Plug in the Ethernet cable that came with your router for this and disconnect wireless.

Download the generic fw from here
http://rapidshare.com/files/351947839/F2404_3_18_1a4_flash_image_NONE.7z.html

Step 1:

grab

you modem and write down the network WPA password and mac address, in the exact same
case as they appear on the
bottom, the WPA key is always uppercase

and the
mac

is

always hex decimal
.

Step 2:

browse over to
https://www.cm9.net/skypass/generate.cgi

tick the box in the middle and
click f@st 2504, on the next
screen add your mac and WPA key exactly how they appear on the
router config page or bottom of router.

make sure you enter the mac address in the exact format with :’s in it e.g 00:1d:74:e
0:7b:8b


Step 2a:

Once you press en
ter it will provide the username and password for your router! This is not magic all
it does is use the algorithm sky uses when sending out the routers. You will notice the first part of
the username if the mac without :’s and the password is random

exampl
e;

Username: 001d74e
07b8b
@skydsl Password: B0/K7ERQ3iGmaC+

Write these down or copy and paste them exactly how they are and keep them safe, save to hd and
to another place i.e usb pen drive.


Step 3:

unzip the file from the top of the guide with

winrar rarlabs.com to some
where

you will
remember
,

the root of your c:

is perfect

Login to the router by putting 192.168.0.1 into your browser and and press enter, then enter admin
as login and sky as the password. Click
on upgrade router at the top once
you are in.


The press cho
o
se file and browse to where ever you unzipped the downloaded achive and select
F2404_3_18_1a4_flash_image_NONE
,

Step 4:

Your router will upgrade

to the generic firmware within 5 mins, do not inter
rupt this process as
it may kill the router. Once finished the router should reboot and your computer will re gain connectivity,
if not manually turn it off and on. Once its back on open up a command prompt by type telnet 192.168.1.1 it
should ask you for
a username and password if telnet doesn’ t work on
windows
7 and vista go to control
panel, programs and features, turn windows features on and off, and click telnet client and press ok, once
it finishes go back to the command prompt and try again.

The use
rname

and password on the new firmware is admin
.

And the router address is 192.168.1.1 for your
browser and telnet this can be changed back to 192.168.0.1 later once you are all sorted, if you have issues
getting

into the ne
w address change over to that su
b net in your lan
IPv4
config
, change back when done/




Step 5:

Configure WAN,

In telnet;

Press 3 and enter for WAN

Press 1 and enter to configure



Follow all the below settings when asked

VPI [0
-
255] (0)





: 0

VCI [32
-
65535] (35)



: 38

WAN ID [0
-
8] (0)




: 1

Category [1
-
ubr,2
-
ubrpcr,3
-
cbr,4
-
rtvbr,5
-
nrtvbr] (1)



: 1

Protocol [1
-
pppoa,2
-
pppoe,3
-
m
er,4
-
ipoa,5
-
bridge] (1)

: 1

Encapsulation [1
-
llc,2
-
vcmux]

(1)


: 2

State [1
-
enable,2
-
disable] (1)


: 1

Service name ()




: SKY (fook knows what this is)

User name

()




: add your username from step 2a

Password ()



: add
your
password from step

2a

Idle timeout (minutes) [0
-
1090] (0)


: 1000

Authenticatio
n method [1
-
auto,2
-
pap,3
-
chap,4
-
mschap] (1)

: 1

IGMP [1
-
enable,2
-
disable] (2)



: 1

QoS [1
-
enable,2
-
disable] (2)



: 1

PPP IP address [1
-
enable,2
-
di
sable] (2)


: 2

PPP MTU [38
-
1492]
(1492)



: 1500


After
you are
done
select 4

to exit and 13

to save and reboot the rooter and you are done.

After steps; Make sure you re enable network security

and configure it how you like…. It should look like
the below

image

http://lookpic.com/i/903/1fvAFV6.jpeg