View Detailed listing

flounderconvoyΗλεκτρονική - Συσκευές

15 Νοε 2013 (πριν από 3 χρόνια και 8 μήνες)

84 εμφανίσεις

EXCLUSIVE OFFER: SURPLUS VACUUM METALLIZERS AND COATING
LINES OF A MAJOR CONVERTER

VACUUM METALLIZERS




General Vacuum EHPT 2250 Vacuum Metallizer, a twin
-
source evaporative vacuum metallizer

for minimal down
time, equipped with a 50" maximum diameter single position unwind with peel
-
off roll, deposition monitoring system
providing closed
-
loop deposition control of individual wire feeds and heat control, optical monitor beam for deposition
con
trol, 24 boats, 3
-
zone vacuum chamber for more efficient deposition, one (1) chill roll, Thermal Care chilled water
system, one (1) Hulvac HVC 340 roughing pump, three (3) Kinnet KT505 LP roughing pumps, three (3) Roots
Holmes HV7000 blowers, three (3) Roo
ts Holmes 13000 blowers, 50" maximum diameter single position rewind with
layon roll capable of running in minimum gap or layon roll mode, Siemens S5 PLC, Siemens Simoreg digital drive
system. Maximum mechanical speed: 2750 FPM. Machine must be removed by
December 31, 2012.







General Vacuum HPAS 210
-
224 Vacuum Metallizer, a free span evaporative vacuum metallizer equipped with a 45"
maximum diameter single position unwind with peel
-
off roll, deposition monitoring system providing closed loop
de
position control of individual wire feeds and heat control, optical monitor beam for deposition control, four (4)
Stokes 412 roughing pumps with two (2) Aerzen GLB 14.9 HV blowers, two (2) Varian NHS 35 diffusion pumps, two
(2) Aerzen GMB 16.13HV blowers,
45" maximum diameter single position rewind with layon roll and minimum gap
capability, Square D Symax 400 PLC, Eurotherm 590 digital drives. Maximum mechanical speed: 2000 FPM.
Machine must be removed by December 31, 2012.





Used Camvac Thetf
ord Vacuum Metallizer, a twin source evaporative vacuum metallizer for minimal down time,
equipped with a 45" maximum diameter single position unwind, dancer tension control, optical monitor beam for
deposition control, eight (8) Stokes 412 roughing pumps
with Edwards EH 4200 blowers, three (3) Varian NHS 35
diffusion pumps, two (2) Varian 305B vapor boosters, two (2) Stokes 149 backing pumps, Polycold PFC 1100 HC,
Polycold 1100 ST, Polycold PFC 1100, inline slitting capability in the chamber, single chill
roll, 45" maximum diameter
single position rewind, Allen
-
Bradley 502 PLC (drive control), Square D Symax 400 PLC (machine control),
Eurotherm digital drive system. Maximum mechanical speed: 2000 FPM. Machine must be removed by December
31, 2012.













COATING LINES





Faustel

coating line equipped with 45" diameter turret unwind with over/under splicing, dancer roll tension section,
spreader roll, 2
-
roll direct gravure coater #1 in enclosure for solvent
-

or water
-
based coating with smoothing roll, 34'
arch dryer with top impin
gement with 2
-
zones for 150
-

550 degree F, 2
-
roll chill roll section, offset pivot type edge
guide, spreader roll, 2
-
roll direct gravure coater #2 in enclosure for solvent
-

or water
-
based coating with smoothing
roll, 34' arch dryer with top impingement in

zone 1 and top & bottom in zones 2 & 3, 24' round dryer with 1 zone for
150
-

550 degree F, 4
-
roll chill roll section, offset pivot
-
type edge guide, dancer roll tension section, 45" diameter
turret unwind with roll change, Eurotherm 590 Digital DC drive s
ystem, Square D SyMax PLC for line control, Allen
-
Bradley 5/03 for DC drive logic, all available spare rolls and parts, all programs and documentation. New Eclipse gas
burners in 2010. Line was running 25
-

165 lb/ream paper. Machine must be removed by Dec
ember 31, 2012.





Magna Graphics coating line equipped with 45" maximum diameter turret unwind with splicing, dancer tension control
section, offset pivot type edge guide, S
-
wrap pull rolls with nip, Flynn flame treater, 3
-
roll gravure coater f
or water
-
based coatings, 19' ASI flotation dryer with 2 zones and gas
-
fired for 150
-

550 degree F, Thermo
-
Electron steam foil
with steam boiler, 2
-
roll chill roll section with nip roll, dancer tension control section, spreader roll, 45" maximum
diameter t
urret rewind with roll changer, Eurotherm 590 Digital DC drive system, Square D SyMax PLC for line
control, Allen
-
Bradley 5/03 for DC drive logic, all available spare rolls and parts, all programs and documentation.
Line was running 25
-

165 lb./ream paper
. Machine must be removed by December 31, 2012.