Guide for the Application for an INCITS 256 Manufacturer ID

confidencehandΗλεκτρονική - Συσκευές

27 Νοε 2013 (πριν από 3 χρόνια και 4 μήνες)

74 εμφανίσεις

Guide for the Application for an INCITS 256


Manufacturer ID


August 2008

Background

With the approval by ANSI of the
American National Standard (ANS) INCITS 256,
American National Standard for Information Technology


Radio Frequency Identification
(RFID
)

and International Standard ISO/IEC 15963,
Information technology


Radio
frequency identification for item management


Unique identification for RF tags

a
system has been created that allows unique assignment of Manufacturer IDs for radio
-
frequency ide
ntification (RFID).
The Manufacturer ID is a mechanism used inconjunction
with a unique RF tag ID used for RFID tags for item management (JTC 1/SC 31).


The manufacturer tag ID is comprised of two 8
-
bit bytes. The first byte is in the form 000xxxxx as
i
dentified in ISO/IEC 15963. The INCITS 256 Registration Authority assigns the value of the
unassigned bits in the 15963 byte (xxxxx). The INCITS 256 Registration Authority assigns the value
of the second INCITS 256 byte.


The structure and allocation of t
he INCITS 256 Manufacturer ID is described in ISO/IEC
15963 and INCITS 256.


autoid.org is the INCITS 256

Registration Authority.


The procedures to be followed by the Registration Authority is defined in standards
mentioned, and may be amended by additio
nal rules from the committee(s). These
procedures and rules are collectively referred to as the
INCITS 256 Registration Authority
procedures.


At the time of writing there were no rules in additional to ISO/IEC 15963 and INCITS 256
from JTC 1/SC 31 or INC
ITS for the INCITS 256 Registration Authority.


An INCITS 256 Manufacturer ID applicant has to pay a Manufacturer ID fee (see below).


This guide has been prepared to assist organizations when applying for an Manufacturer
ID, by providing extra informatio
n on the application procedure. This guide does not
replace ISO/IEC 15963 or ANS INCITS 256.


The INCITS 256 Manufacturer ID issued by the Registration Authorities are published in
an
INCITS 256 Manufacturer ID Register
.

Application for an
INCITS 256 Manufacturer ID

Organizations that wish to secure an
INCITS 256 Manufacturer ID
assignment shall apply
to the Registration Authority for registration and the assignment of an
INCITS 2
56
Manufacturer ID
using the application form attached as Annex B. The Registration
Authority will verify the validity of the application conformant to the
INCITS 256
Manufacturer ID
registration procedures and assign an
INCITS 256 Manufacturer ID
if the
c
onditions for approval are met.


Applicants are advised to refer to ISO/IEC 15963 for the obligations of an
INCITS 256
Manufacturer ID
applicant. ISO/IEC 15963 and ANS INCITS 256 can be obtained from
your national standards organization.

INCITS 256 Manu
facturer ID Fee

autoid.org will charge a fee to recover the costs of the INCITS 256 Manufacturer ID
registration. autoid.org charges for the initial registration a fee of $500.00 (USD) for a
registration period of 2 year (24 months) for each assigned INCI
TS 256 Manufacturer ID.
For every subsequent prolongation of the registration for a period of two years an
additional fee of $175.00 (USD) is charged.


(Note:
autoid.org
reserves the right to change the fee of the registration service)


For initial regist
ration autoid.org will send an invoice to the address for
correspondence/billing, after the Registration Authority has verified that the application
meets the approval criteria.


For prolongation of registration autoid.org will send an invoice to the addr
ess for
correspondence/billing, one month before the expiration of the registration period.

Contact points

For additional information on Registration and Assignment please contact:










Mr. Craig K. Harmon

autoid.org

3963 Highlands
Lane, SE.


Cedar Rapids, IA 52403
-
2140 USA




(V).

+1 319/364/0212





(E):

craig.harmon
@autoid.org


For additional information on INCITS 256 Manufacturer ID fee payment please contact:


Mr. Craig K. Harmon



autoid.o
rg




3963 Highlands Lane, SE.


Cedar Rapids, IA 52403
-
2140 USA




(V).

+1 319/364/0212





(E):

craig.harmon
@autoid.org







Annex

A


Application form for an INCITS 256 RFID Manufacturer ID

This request is submitted in accordance with American National Standard (ANS) INCITS 256,
American
National Standard for Information Technology


Radio Frequency Identifica
tion (RFID)

and
International Standard ISO/IEC 15963,
Information technology


Radio frequency identification for item
management


Unique identification for RF tags
.


A.1 To be completed by the requesting organization


Name of organization



Address to
be registered



Principal contact in organization




Telephone number

Fax number



Email address of principal contact



Address for correspondence/billing





Date

Signature





A.2 To be completed by INCITS 256 registration authority


Registered app
lication provider identifier



Date

Signature