2 DIODE CLIPPING and CLAMPING CIRCUITS

bahmotherΗλεκτρονική - Συσκευές

7 Οκτ 2013 (πριν από 4 χρόνια και 1 μήνα)

244 εμφανίσεις

Electronic Circuits I Laboratory


10
2 DIODE CLIPPING and CLAMPING CIRCUITS

2.1 Objectives

• Understanding the operating principle of diode clipping circuit
• Understanding the operating principle of clamping circuit
• Understanding the waveform change of diode clipping and clamping circuits
when the bias is applied.

2.2 Basic Description
As you know, diodes can be used as switches depending on the biasing type,
reverse of forward. The clipping circuit, also referred to as clipper, clips off
some of
the portions of the input signal and uses the clipped signal as the output signal. The
clamping circuit or clamper keeps the amplitude
of the output signal same
as that of
the input signal except that the D.C. level (offset) has been changed
. The clamper
through which the input waveform shifts to positive direction is called positive
clamper, otherwise, is called negative clamper.

Fig. 2.1 – Ideal Diode – Switch Terminalogy
2.2.a Clipper Circuits
There are two types of clipper circuits, the series and parallel diode clipping
circuits.
2.2.a.1 Series Diode Clipping Circuit


In these type of circuits, the diode is connected between the input and output
voltage terminals (Fig 2.2)







Electronic Circuits I Laboratory


11




Fig. 2.2

As Fig.2.2 reveals, the negative cycle of the input voltage can be clipped of by
this type of series clippers. Reverse of the diode pins yields to a positive cycle
clipping circuit as shown in Fig. 2.3.








Fig. 2.3
Previous circuits clip the values larger or smaller than zero voltage. This
voltage, technically called “threshold voltage” and can be changed to a desired value
by inserting a D.C. voltage source. This is achieved in two different ways.
In the first type, the voltage source of E
m
( positive or negative) is connected
through output terminals as in Fig. 2.4. Depending on the diode connection (normal
Electronic Circuits I Laboratory


12
or reverse), the values smaller (Fig.2.4.a) or greater (Fig.2.4.b) than E
m
is clipped

and assigned as E
m
. .
a
b
Fig. 2.4.
Ö Note that if E
m
is negative, ( where the voltage source is reversely connected)
again the values smaller or larger than this negative value is clipped, do not get
confused.

In the second type of thresholded series clipping, the voltage source is
applied between the input and output terminals, series with the diode. This time, the
clipped values are assigned to zero
and the net output voltage equals to the
difference between the input and threshold values.(If E
m
is negative, then E
0
= E – E
m

= E + |E
m
|)

a
b
Fig. 2.5

Electronic Circuits I Laboratory


13
2.2.a.2 Parallel Diode Clipping Circuit

In this type of clippers, the diode is connected between output terminals. The
on/off state of diode directly affects the output voltage. These type of clippers may
also have a non-zero threshold voltage by addition of a voltage series with diode.
Following figures illustrate the clipping process.

a

b
Fig. 2.6 – Zero Threshold Parallel Clippers

a

b
Fig. 2.7 – Thresholded Parallel Clippers

Electronic Circuits I Laboratory


14
2.2.b Clamper Circuits
Clamper Circuits, or briefly clampers are used to change the D.C. level of a
signal to a desired value.( Fig 2.8 ).

Fig 2.8
Being different from clippers, clamping circuits uses a capacitor and a diode
connection. When diode is in its on state, the output voltage equals to diode drop
voltage (ideally zero) plus the voltage source, if any. Now let us examine the
clamping process for the circuit in Fig. 2.9.




Fig 2.9 – Typical Clamping Circuit
As you know, this circuit, in fact, is a series R-C circuit. The resistance of diode
( several ohms above its drop voltage) and the small capacitance yield to a small
time-constant for this circuit. This means that the capacitor will rapidly be charged if
any input voltage, that is enough to swtich on the diode, is applied. The diode will
conduct during the positive cycle of the input signal (Fig. 2.10) and output voltage will
be ideally zero ( in practice this voltage equals ~0.6 V).

Fig 2.10. Diode conducts during positive cycle
Note that during positive cycle the capacitor is rapidly charged in inverse
polarity with the input voltage. After transition to negative cycle, the diode becomes to
its off state. In this case, the output voltage equals to the sum of the input voltage
and the voltage across the terminals of the capacitor which have the same polarity
with each other.(Fig 2.11)
Electronic Circuits I Laboratory


15
E
0
= - ( |E
i
|+ |E
c
| )





Fig. 2.11. Diode is switched off during negative cycle

The resulting signal after a complete cycle is shown below.

Fig. 2.12
By this process, the input signal is shifted to negative D.C. value (its maximum
value is ideally zero) without any change
in its amplitude ideally.

There exist again modified versions of this circuit inwhich a threshold value is
inserted for clamping. Following figures illustrate these modifications and resulting
outputs.







Electronic Circuits I Laboratory


16


Fig.2.13



Fig. 2.14



Electronic Circuits I Laboratory


17
2.3 Experiment Equipments
1. KL- 200 Linear Circuit Lab. Device
2. Experiment Module: KL-23001
3. Experiment Instruments: Oscilloscope, Multimeter
4. Connection cables and short-circuit clips
2.4 Procedures

Procedure 1: Series Diode Clipping Circuit
( 1 )
Locate block b of module KL-23001

( 2 )
Insert short-circuit clips refering to Fig. 2.15 a






Fig. 2.15

( 3 )
Using oscilloscope, adjust function generator to 10 V p-p ( 7.07 V rms)

, 1kHz Sine wave
. Make a good adjustment since this signal is the common
input signal that will be used during whole experiment.


( 4 )
Adjust oscilloscope divisions until you have a clear view of input signal.

Electronic Circuits I Laboratory


18
( 5 )
Disconnect function generator output from oscilloscope and apply this
to TP2.

( 6 )
Examine the output signal by connecting the second channel
of
oscilloscope to TP3. Record the plot on Graph 2.1 a.


( 7 )
Turn off all active devices, and reconfigure the short-circuit clips refering
to Fig. 2.15 b.

( 8 )
Only change the generator output from TP2 to TP1.

( 9 )
Again examine the output waveform and plot output waveform on
Graph 2.1.b






a b
Graph 2.1







Electronic Circuits I Laboratory


19
Procedure 2: Thresholded Series Diode Clipping Circuit
Ö In this procedure, a threshold value is added to the previous circuit layout.
This is achieved by substitution of lower short-circuit clip with a voltage source.

( 1 )
Turn off all active devices, and connect short-circuit clip and voltage
source ( + 5 V DC) by refering to Fig.2.16-a.

Fig. 2.16

( 2 )
Record the plot of output voltage on Graph 2.2.a (on Pg. 25)

( 3 )
Turn off all active devices, and reconfigure short-circuit clips refering to
Fig.2.16-b.

( 4 )
Plot output waveform on Graph 2.2.b

Ö Turn off all active devices. Now you will apply negative threshold value to
the clipper circuit.

( 5 )
Refering to Fig.2.17-a, reconfigure short circuit clips and substitute +5V
DC source with -5 V DC Source. Do not directly reverse the terminals of
+ 5 V source, this will cause a short circuit !!!

Electronic Circuits I Laboratory


20

Fig. 2.17
( 6 )
Observe and plot the output waveform on Graph 2.2.c

( 7 )
Turn off all active devices again and rearrange short circuit clip refering
to Fig.2.17.b

( 8 )
Observe and plot output voltage on Graph 2.2.d











Electronic Circuits I Laboratory


21
a b

c d
Graph 2.2

Procedure 3: Parallel Diode Clipping Circuit

( 1 )
Locate block c of module KL-23001

( 2 )
Refer to Fig.2.18-a and arrange short circuit clips.

Electronic Circuits I Laboratory


22

a
b
Fig. 2.18
( 3 )
Observe output voltage on TP2 and plot on Graph 2.3.a
( 4 )
Turn off all active devices and rearrange short circuit clips by refering to
Fig. 2.18 b.
( 5 )
Observe output voltage on TP2 and plot on Graph 2.3.b
a b
Graph 2.3

Electronic Circuits I Laboratory


23
Procedure 4 : Diode Clamping Circuit

( 1 )
Now locate block e.

( 2 )
Arrange clips according to Fig.2.19-a.

a
b
Fig. 2.19

( 3 )
Observe and plot OUT voltage on Graph 2.4.a
( 4 )
Turn off all active devices and rearrange circuit in Fig. 2.19-b
( 5 )
Again plot OUT voltage on Graph 2.4.b.






Electronic Circuits I Laboratory


24
a b
Graph 2.4
2.5 Conclusion
In this experiment you have learned two main types of diode circuits.

• Clippers
• Clampers

Although the clippers are also classified into series and parallel clipping
circuits, both circuits are based on the same principle. In other words, the design of
both circuits utilizes the characteristics of diode that will be forward turned on and will
reversely turned off.

Clampers can be used to change the DC level of an input signal.